Have the issue of connecting a pc an NAS to a E4200 and when transferring from pc to NAS, only getting < 10 mbps transfer rates? NAS is Dlink 321. PC has Gigabit ethernet card. cables are cat 6. Even when I force the NAS and pc network card speeds to 1.0 GBps full duplex, I only transfer files at < 10 Mbps.
View 3 RepliesI just upgraded to an E4200 from a D-Link DIR-655. I cannot seem to get my desktop to connect to the E4200 at 1 GBS. My adapter is set to "auto negotiate" but will only connect at 100 MBS. If I try forcing the adapter setting to 1 GBS, it never connects. I can swap out my E4200 with the DIR-655 and it will connect at 1 GBS just fine. I am using a CAT 5E cable. Is there something I'm missing here or is the E4200 just more finicky than the the DIR-655?
View 9 Replies View RelatedI recently bought the E4200 thinking it would be the latest and greatest, and I wouldnt' have to worry, but after just a simple test of transferring files between my Home Server, and my PC (Both connected over Gigabit ethernet using CAT6 cables, with only the E4200 inbetween).I use to get anywhere from 40 MegaBytes/second to 50MegaBytes/second on my D-Link 655.But now I am lucky to barely get 20 MegaBytes/second. Is there an issue with this router? or am I expecting too much from Linksys?
View 6 Replies View RelatedIf I connect wire directely to the PC Ethernet port the Internet speed is about 400 Mbit/sec (speedtest.net)When my PC is connected through the Linksys E4200 Internet speed is not above 90 Mbit/sec.
View 1 Replies View RelatedI have that red gigabit router with the 150/65 service. It connects via ethernet for internet and has a coax to transmit the guide data etc.So my idea was to just leave the Verizon router connected and on (with wi-fi off) so it could do the TV stuff and just plug my router into the ethernet wall port the Verizon guy installed.Not so easy of course, my E4200 will not recognize the ethernet from my ONT (I think that's what the device they put in my basement is called) and the internet doesn't work. I have factory reset the router.The reason I am doing all this is because the wireless range of the e4200 at 2.4ghz is near unmatched and given my house, the actiontech cannot reach my room.
View 9 Replies View RelatedI have what should be simple. Home network on cable. WRT320N is main router cabled to desktop with GB card. It is hard-wired to a Netgear WNR3500L (also gigabit). That router is hard-wired to a desktop with GB card. For testing I connected a second machine hard-wired to the WRT320N with a 10/100 card. All machines recognized cards properly at correct speed. I ran LAN Speed Test between machines. Speeds were comparable between machines regardless of cards. GB -> GB was mid-30's write, mid-80's read with GB -> 10/100 a couple of ticks slower but not significantly. The LED's on both routers will show different color if GB connection and both showed GB for the desktop connection but not the interconnect between the routers. The routers are connected at about 100' with CAT5E and straight-through.
View 5 Replies View RelatedI'm currently using onboard lan card of P6X58D Premium. However in the Cisco web setup page or even in my Windows 7, it shows only 100Mbps connection. I tried to force to 1000Mbps but it failed to get an IP. I did a google and found that may be the router doesn't do well with Intel card, but I use another onboard lan card with Nivida chip+AMD CPU, it's still only have 100Mbps. What can I do to have a 1000Mbps connection?
View 5 Replies View RelatedHow do I go about opening specific ports on an E4200?I'm having disconnect issues with a particular game, and the Customer Service drone thinks the ports required for the game aren't open. Nevermind the fact that it's worked fine for 6 months now, and the problem only started a few days ago.I figured I'd humor the idiot and open the ports, but all I can find is information on forwarding, not making sure the ports are open
View 3 Replies View RelatedI've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies View RelatedIs there a way to force a specific speed for the local ports? I'd prefer not to rely on the autonegotiation.
View 5 Replies View RelatedI posted my complaint on Amazon.com recently. My E4200 router stopped allowing traffic through ports completely. I was able to unplug the power and allow the router to cool, and the router would work for a while then stop after about 10 minutes. I assume that the unit was overheating, but I do not have the equipment of a test facility.I bought a Belkin AC 1200 router which is a bit of an upgrade from Amazon.com. I do not think that there is anything that Linksys can do for me as my warranty expired. I just thought that when I spent what was to me a lot of money the router should have lasted longer.
View 5 Replies View RelatedIs there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View RelatedAs soon as i modify my wireless to be unsecured, I looy ability to usse me the internet on all wired ports as well as all wireless. From the routers point of view it still has a good solid internet connection. Passes traceroute, but wont allow any wired or wireless connections on the internet. I'm trying to get a Linksys WRE54G v1 to work with this so my parents can have internet once more. If i manualy remove the security to allow the one touch Auto configuration button to work i loose my ability to surf until i run the Cisco Connection software to turn back on the passwords.
View 7 Replies View RelatedI've had for several years very good experience with the WRT54GL. Based on that experience I upgraded to a e4200.But so far it's not living up to my expectations (media server not probably working with external harddisk, no advanced logging of incoming/outgoing traffic, connection problems) and I'm getting pretty frustrated with it.Problem right now is that one of my laptops with Windows 7 is often not connecting correctly to the wireless network of the e4200. It's giving a "unidentified network" error. Rebooting computer and router is not working. The computer is (always) reliable connecting to another wireless network in my home. It seems the DHCP is not working properly?
View 1 Replies View RelatedI think I have worked out that you can`t currently connect a usb printer to the usb port on the e4200 in order to share it over the network.
However I have heard reports that this might facility might be enabled in the spring.
I have also heard something about `virtual usb` but I don`t know whether this has anything to do with it.
Have a Linksys E4200 router located in my basement and I am experiencing a puzzling wired connectivity issue as follows: Port 1 on the router is for my study, I have no problem getting connection regardless if I use my study's Ethernet jack or if I run a 5 ft. cable (hereinafter THE CABLE) from the router’s port 1 to my laptop (i.e., cabling does not make a difference).I then connect to router port 1 an EZXS55W Linksys switch (using port 1 on the switch and THE CABLE) and then connect my laptop to port 2 on the switch using a second cable. I am unable to connect to the network/internet even after rebooting both the cable modem and router.I then reconnect my study to port 1 on the router, I go to my study and connect the study’s Ethernet jack using THE CABLE to port 1 on the switch and using a second cable from port 2 on the switch to my laptop. …. I get an network/internet connection immediately ! FYI, I have had the exact problem with switches EZXS88W and SE2500 (no longer own this).
View 5 Replies View RelatedI've been messing around with this for several weeks to no avail. I've never had a problem establishing a VPN connection within my LAN. I've tried several workarounds, learning things in the processs, but to no avail.I've set up a VPN connection with Windows 7. The RRAS server is at home and I'm attempting to access from school (or the internet anywhere).I have no problem establishing the VPN connection (that I can see). Port 1723 is forwarded for both UDP and TCP to a static LAN address (198.162.1.124) in the E4200. PPTP pass-through is enabled (as well as the other two options).I can't see anything on the server after connecting. I'm using a DDNS. It works just fine INSIDE the LAN; I've even mapped a network drive to "S:". Accessing ANYTHING outside of the LAN over a VPN, however, isn't working. [code]
View 9 Replies View RelatedI have an issue with a brand new E4200 router. My E4200 can connect no issue with the following devices: Ipad, AppleTV, Dell Laptop, Ibm Laptop. It is also wired connected to my home PC. Internet works fine and file sharing/network works good for all the above devices.
The problem is that My wife and I's Phone can not detect the wifi network and can not connect to it. The SSID broadcast is enabled on both frequencies (2.4 and 5). I have try configuring the network manually on both the Android phones..it does not work.. it records the data but keep sayng the network is out of range (although I'm right next to the router). I hva eplayed with various channels on both frequecies and played also with the MTU size.One of the Android phone is Garmin the other Acer Liquid...different brand running both Android 2.2...
Firmware on E4200 is 1.0.02
All settings reset to Auto/MIxed for now.
WPA2 is enable with security key
SSID is enabled on both frequency
no MAC address filtering is setup
Both my phones can detect other networks and can connect fine to friends and family networks...So I suspect a compatibility problem between router an Android..I have contacted Linksys support twice with no avail. I have contacted both Acer and Garmin...they refer me to linksys
I am trying to replace my Cradlepoint MBR1200 with a CBR450 in bridge mode, to let the E4200 take over all the WAP and DHCP handling, but having a hard time.I set the CBR450 in bridge mode and when I connect it to my laptop it properly passes the IP info to my Mac and allows me to connect. I then connect it to the E4200 WAN port with it set to get IP address automatically but nothing ever happens and I am never allowed traffic in/out over the WAN.
I *can* get internet access by leaving the CBR450 in normal mode (handling DHCP, etc) and then plugging it into the E4200 LAN port and having the E4200 set to bridge.why the E4200 WAN port is not getting the bridge info and allowing connection? FWIW, works fine connecting to a DSL modem with the DSL model set to bridge mode at my other house.
CBR450 and E4200 both on latest firmwares.
I purchased a WAG320N and E4200 and have manged to get the modem connected to the internet and it's running fine in that respect, with no adjusting done to the settings.My intentions are to connect the WAG320N to the E4200 wirelessly, as they are in seperate rooms in the house and have done a similar setup in the past with a 7300G Billion Modem and WRT54GL.
With the E4200 I quickly discovered there was no bridge mode out of the box, but checking these forums got the indication that the firmware updates added this capability, so updated it..I entered the IP Address of the Router, the Subnet mask of the network and the Default Gateway / Modem router IP address into the fields, following this guide, but have not been able to get the computers to contact one another, nor ping the other devices.
I have an E4200 wireless router which is connected via USB to my Canon MX 308 printer. I am able to print from Windows computers that are connected to this router (via WiFi of course). My iPad 2.0 is able to connect to the internet via the router. However I am not able to print content from my iPad via the E4200 router (via Wifi using Cisco Connect software).
View 1 Replies View RelatedI'm trying to connect the D-Link 930L Wireless N Camera to my E4200 router. When I have the camera connected via the Ethernet cable it works fine, as soon as I unplug the Ethernet cable it will not connect wirelessly. I tested the camera on a friends router E3000 and the camera connects fine and work flawlessly on his network wirelessly. Any settings in the router that need to changed or set differently?? All of my other devices work great. I have been through D-Links Tech support all things point back to my router.
View 6 Replies View RelatedI have a new E4200 with the latest firmware and my slingbox seems to not be playing nice with the router. It refuses to take the IP I reserved for the SB, but always defaults to 192.168.2.254. I use a 2 subnet just in case you're wondering. I have tried multiple reboots and the IP does not change. I have tried turning off UPNP, figuring that was hijacking the dhcp server, but that hasn't changed anything. I also notice that a few of my connected devices do not show up in the dhcp list, yet they connect and work ok.
View 2 Replies View RelatedI was attempting to use my EA4200 in bridge mode but found out for some reason my devices weren't connecting to the internet. So I decided to try to access the router through the IP address of the router with no avail. So I pull the router and plug it in normally and notice that it keeps flashing. So that already gives me an idea something is wrong. I go through the process of unplugging everything from the router, and plugging my PC directly into the LAN port 1 of the router then powering it up. On my network connection list it keeps trying to identify the network but keeps failing (keep in mind that the router still is flashing). So I decide to attempt a 10 second reset, then a 30 second, then a 30-30-30. All with no success. The router keeps flashing.
Which gets me to the point where I am now... router flashing at me, and wondering if this now out of warrenty unit was a waste of money. I am noticing that a lot of people have had questions and issues with the E4200v2 which now concerns me, well hopefully this can be fixed.
Last week I purchased the E4200 and for simplicity, I configured it with basic settings using Cisco Connect. Today, I went into the web interface. The only thing I did was review settings and get the Routers PIN (it appears that Intel Chipset cards on Windows requires this PIN?) Close the browser (did not save any settings) and now I am completely locked out of the device. Cannot connect does not accept the wireless password. I hard reset the device, ran through the wizard. Everything was working again. Launch the browser and connected to the device closing window and balm?
View 9 Replies View RelatedMy router is on a static IP, it is a Linksys WRT150N, and it doesn't have gigabit ports. Is it possible to run it through the 1522's gigabit ports.Modem -> 1522 -> actual router.
View 2 Replies View RelatedCan I turn off the wireless network of linksys E4200 and use only the 4 ports? using the router like a 4 port switch?
View 2 Replies View Relatedi purchased an E4200 router to replace my old WRT150N. I had a WUSB300N that connected fine to the old router, but it's not connecting to the E4200. I have a guest network set up on it, and the adapter can connect to that, so I'm at a loss as for why it won't connect. Does anyone think it has something to do with the type of security I have set up? I had it on WPA2 on my WRT150N, and the E4200 on WPA2/WPA mixed mode.
View 2 Replies View RelatedI've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies View RelatedI have a Dlink Wireless N Xtreme DIR-655 I have run out of port 4 on it to a switch with a cat 5 patch cable that is 25 ft long It is connected to the Internet port on a Dlink 4 port switch. When i run from that on any of the 4 ports back to my computer ( Win7). I get no internet access but if i connect the cable straight from the router there is no problem. I even attempted to use a older dlink router for the switches and no luck there at all. Any reason the internet would not be broadcasting through the switch.
View 3 Replies View RelatedThe problem I have run into is that I am not getting any connectivity between my two gigabit ports on the 1941. I have ge0/0 setup as my internal network and is running dhcp, ge0/1 is the connection to the modem. I can't figure out how to configure the connections so my internal traffic on ge0/0 routes out through ge0/1.
Here is my config:
Using 4312 out of 262136 bytes
!
[Code].....
how the ASR1000s are being setup.I am looking at ASR1000s as part of network refresh and was looking at RJ-45 based Gigabit Ethernet ports compatible with the ASR1000s SPA-5X1GE-V2 seems to be an option but they are all SFPs. Are there any options for RJ-45 ones on ASR1000s?
There is an option for the 2 port where one can mix and match SFPs and RJ45 but I was looking for something which is RJ45 only.Are there any options for them available.I know I could get something with FastEthernet type but was looking for the GigabitEthernet type.
My HD Configuration is:
+ WRT310N v2 ,
+ Win7 x64,
+ Realtek RTL8168C(P)/8111C(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20)
My connection is still 100.0 Mbps.