Wireless N Extreme DIR-655 Connecting Switch To Router To Expand Ports
May 18, 2011
I have a Dlink Wireless N Xtreme DIR-655 I have run out of port 4 on it to a switch with a cat 5 patch cable that is 25 ft long It is connected to the Internet port on a Dlink 4 port switch. When i run from that on any of the 4 ports back to my computer ( Win7). I get no internet access but if i connect the cable straight from the router there is no problem. I even attempted to use a older dlink router for the switches and no luck there at all. Any reason the internet would not be broadcasting through the switch.
View 3 Replies
ADVERTISEMENT
Aug 4, 2011
I have a wireless network in a 2 storey house. The internet access and 1 WRT54GS router is on the 1st floor (using frequency channel 11). The wireless single doesn't do very well on the second floor unless there is a device with a strong antenna. I recently purchased a WET610N Bridge and I have an extra WRT54GS (using frequency channel 1).
I would like to be able to add wireless to the 2nd floor by attaching the extra router to the bridge which would wirelessly connect to the router with the internet.
View 2 Replies
View Related
Aug 19, 2011
I have an airport extreme router connected in my basement. My family room Ethernet connection is connected directly to the airport extreme. I can access the internet by Ethernet in the family room just fine.What I want to do is use a WRT31N as a switch in my family room so I can connect Mulitple Ethernet devices to the network. I'm having a hard time doing this. How to set up the linksys router? The airport extreme ip address is 10.0.1.1. I tried setting the linksys to 10.0.1.2 and turning off dhcp, but didn't work.
View 1 Replies
View Related
Jul 6, 2011
I have a netgear CVG834G main router, were my desktop is plugged on to.I pulled a new cable trough the house and garage to have internet access on the other side (cable length is about 80 meters).After the 80meters of cable I placed a Linksys WRT54GS v5.1 router. The problem is that I can connect to the Linksys, but the Linksys can�t connect to the netgear. On the Linksys the internet LED is blinking very slowly (what does this mean?). So first I thought that the cable was broken or too long. I tested the cable => not broken. I connected the Linksys with the netgear trough a shorter cable and then connected my laptop via the long cable (80meter) and this works perfectly.Is the maximum distends a netgear can take less than 80 meters? (thought is was 100meter ).
View 3 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Aug 16, 2011
how to Cascade two routers on one subnet, but when I disable DHCP on the slave router, I cannot add in any DNS settings.
View 4 Replies
View Related
Aug 2, 2012
I have a network which was recently switched from dsl to comcast. The default network is 10.1.10.1. The dhcp is working with the 5 or 6 installed pc's. All pc's are running xp professional.I inserted the dlink 4 port switch to add a new port by inserting it between the router and a pc.
View 4 Replies
View Related
Aug 7, 2011
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies
View Related
Aug 29, 2011
Currently I have the modem into an apple airport extreme, this provides WiFi to the whole house + has a NAS drive connected to it...I have two x box's on the top floor of the house... One is currently wired to one of the airport extremes LAN ports...Now what I am trying to achieve - the second xbox is an old one so needs to be plugged in by cable too... (and I don't want two cables through the house). I have an old Netgear wpn824v2 router. Now so far I plugged the ethernet cable from airport x into one of the lan ports on the Netgear...Then both xboxs are wired into the netgear... The netgear has basically nothing setup on it - no security etc... ip address is on the same network as DHCP router.Netgear has upnp and dhcp disabled...Now stand alone one xbox at a time, the connection is actually faster than I have ever achieved, the full 50mb - but if i wire up my laptop to the netgear and use the internet at the same time the xbox lags like hell, so obviously not tried both xboxs together yet as it will just cause lag!
*modem* ----- wired to ---------
-----airport extreme(provides WiFi to house)* ----- Wired to --
-----*NAS drive* --- AND---
-----*top floor to the second router - Netgear* ---wired to ---
----*2 Xbox's
View 1 Replies
View Related
Jan 19, 2012
Have the issue of connecting a pc an NAS to a E4200 and when transferring from pc to NAS, only getting < 10 mbps transfer rates? NAS is Dlink 321. PC has Gigabit ethernet card. cables are cat 6. Even when I force the NAS and pc network card speeds to 1.0 GBps full duplex, I only transfer files at < 10 Mbps.
View 3 Replies
View Related
Apr 21, 2013
in our office we have an Internet connection 20Mb upload and 20Mb download from XO our ISP provider.When my users connect using an ethernet cable to there laptops they get a speed of 18.34 download and 18.15 upload ping 7ms according to Speedtest.net.But when they connect using the wifl Access point Apple Airport Extreme they get the download speed 10.7 Mb and upload 14.5 Mb.Why such a difference in speed to the Internet? Is there a setting on the port on the Cisco SLM248G that I need to set for which the Access point is connected to.
View 3 Replies
View Related
Aug 15, 2012
We will be connecting Cisco 4507 with Extreme Switches. We ran into spanning-tree issues last time. Extreme does not understand spanning-tree. So what i am thinking it to prevent bpdu advertisement from 4507 to extreme switches and also prevent incoming bddu from extreme switch to 4507. I am thinking of using
spanning-tree bpdu filter
spanning-tree bpdu guard
spanning-tree root guard
View 13 Replies
View Related
Jun 28, 2012
We have a customer that has a fiber rum between 2 building. They want to have 2 seperate fibers active that terminate into the same switch on each end. (redundancy).
In building A they have an extreme networks black diamond switch that does not support STP.In bulding B they have a Cisco 4507.
We will ahve to use a layer 3 routed connection due to the fact their switch in building A does not support STP.Our tech does not want to use static route becuase he does not want to setup IP SLA for the redundant connection.
Will RIPv2 work for this scenario and failover to the other fiber if needed? The hop count is the same for each fiber path..
View 2 Replies
View Related
Aug 23, 2011
I just bought a e3000 and I have a 24 ports switch. I would like to plug more than 8 pc...how do I proced ? I used to have a dlink router and just plug a cat5e from the dlint to the switch ... but it doesn't work with the e3000
View 5 Replies
View Related
Aug 17, 2012
My brother has a router for his house which lives right next door. I am getting wireless through a adapter right now but not good throughout my house.
View 1 Replies
View Related
Jul 5, 2012
I cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies
View Related
Sep 29, 2009
I just installed a Linksys WRT160N router. The signal started of good about 50 to 70 feet from the routers location. Now the signal is registering as low to good, about 54Mbps. I was wondering what options I might have to install a wireless bridge for expansion of the signal. I have configured an encrypted network using WPA2. I am wondering what the technical difficulty would be to install and configure it. I setup the WRT160N myself if that means anything.
View 4 Replies
View Related
Aug 16, 2011
My DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
View 1 Replies
View Related
Sep 27, 2011
I have a wrt160n that I would like to use to expand the range of my wireless network. I have tried a few solutions, but to no avail. I am thinking I have just not found the proper steps.I am behind a dsl wireless router that Telus has provided me. The values of that router setup are as follows:SSID: TELUS4108WPA/WPA2-AESDefault gateway: 75.156.190.1DNS address: 199.185.220.254Subnet mask: 255.255.255.0
View 9 Replies
View Related
Aug 20, 2011
I went out and bought a e4200 today and the signal strength is worse than my WGT300n, is there any tweaks I can do to expand my signal strength?
View 3 Replies
View Related
Nov 24, 2012
Have a Linksys E4200 router located in my basement and I am experiencing a puzzling wired connectivity issue as follows: Port 1 on the router is for my study, I have no problem getting connection regardless if I use my study's Ethernet jack or if I run a 5 ft. cable (hereinafter THE CABLE) from the router’s port 1 to my laptop (i.e., cabling does not make a difference).I then connect to router port 1 an EZXS55W Linksys switch (using port 1 on the switch and THE CABLE) and then connect my laptop to port 2 on the switch using a second cable. I am unable to connect to the network/internet even after rebooting both the cable modem and router.I then reconnect my study to port 1 on the router, I go to my study and connect the study’s Ethernet jack using THE CABLE to port 1 on the switch and using a second cable from port 2 on the switch to my laptop. …. I get an network/internet connection immediately ! FYI, I have had the exact problem with switches EZXS88W and SE2500 (no longer own this).
View 5 Replies
View Related
Jun 19, 2011
For the past year my wireless has been working great and I have being playing games/doing homework with no hassle. Yestetday my internet connection became very slow. After countless restarts, router/modem resets nothing has changed and I only get like 5kb of download speed. Since my internet connection was lost naturally I unplugged the wireless card and re-plugged it, didn't change anything. After that I restarted my computer, but nothing changed. AFTER THAT I unplugged my router, then reset my router to factory settings, which did not change anything. Since everything was backed up I thought I would reinstall Windows 7 to nuke any hidden problems. After 2 reinstalls of Windows 7, nothing has changed. Next I had Comcast reset my connection with them which did not work. Though it did work with my brothers desktop. After some more time just fiddling around my connection went back to lightning speeds. no.....4 hours later my connection went dead.At all times my computer will see my network but it either will not connect to it or it is really really slow now.
Computer info: Apple Airport Extreme router Hawking HWUN3 Wireless USB ASUS P6T Motherboard
View 2 Replies
View Related
Sep 22, 2011
I've recently purchased an E4200, and while it works great, I'd like to use my Apple Airport Extreme (2nd generation) to extend my network to another part of the house that doesn't get as great of a signal. I've become very frustrated trying to accomplish it, and I'm not sure if the problem is more from the Linksys end, the Airport end, or if it's just me.
View 3 Replies
View Related
Jan 25, 2012
I have a E4200v2 i also have a Airport Extreme I want to use this to extend my wireless range in my house? I've played around a little tring to configure the Airport extreme but can't seem to get it to connect to my E4200v2? Can you mod the Airprt Extreme with dd-wrt or something that might unlock some of the features?I can't stand the interface. The E4200v2 is brand new.
View 1 Replies
View Related
Feb 10, 2012
The router will serve as an access point for 10 wireless station, 6 of them will run over Terminal server, the router will also serve 20 computer for the internet, so I want to Link aggregate the four LAN port to my swtich, I know how to do it on my Dell Powerconnect, but I want to know if the WRVS4400N will support it, there will be a lot of traffic going through the router so linking the 4 port in LAG mode to my Powerconnect swicth will speed up the communication
View 1 Replies
View Related
Jan 13, 2013
My computer is not wireless so I have needed a wireless router from Time Warner. Directions tell me to connect to my computer. Will that solve the fact that my computer is not built in wireless?
View 2 Replies
View Related
Aug 9, 2012
Can a router connect to a switch to gain additional ports (to both access the internet AND to maintain an internal / home network)?IP line to house, connected to modem, connected to 4-port router, connected to 8-port switch. Now, each of six rooms in my house has one Cat-5e (RJ-45) jack whose run terminates to the switch. In some of these rooms, I need two wired devices (wireless isn't an option for the devices). Can I use the LAN port of a spare, wireless router (to also use as an access point for cell phones, etc) to plug into the jack and increase the number of ports in that room to have a functional LAN and WAN? I have read tons of info on plugging switches into routers to increase the number of ports, but not the other way around. Plus, ripping open walls to expand the network isn't feasible either. My other thought, would be to replace the switch with another (2nd) router, by connecting the 1st and 2nd routers together, and have the runs terminate to the open LAN ports of both routers --= and then expand the ports in those rooms by also using additional, spare wireless routers.
View 14 Replies
View Related
Jan 16, 2012
this router of my girlfriends only works when iplug the dsl modem into the output ports what could possibly cause this. would a firmware upgrade straighten it out...
View 1 Replies
View Related
Mar 27, 2012
I am having a problem with setting up the 2 different networks. It says I am able to have 2 networks in this 1 router and I was able to set up the 2 networks, but i do not see the second network in my network list. I have a total of 7 devices that are connected to the router and my main thing I wanted to do was have 1 laptop on its own network and be able to use the 5ghz channel.
View 1 Replies
View Related
Jan 16, 2011
Currently We have an RV016 setup and Setup>Network we have the following settings:
Host Name: pagegateway
Domain Name: mycompany.com
Device IP address: 10.20.181.1
Subnet Mask: 255.255.255.0
DHCP Server is not enabled on the RV016. We currently have a Windows 2003 Server that is acting as Exchange Server, Active Diretory, and DHCP Server. My issue is that we are running out of IP addresses and I have about 20 or so left to assign. Given the above setting can I make changes to my RV016 to give me more than 256 addresses? If yes what do I need to do and do I need to make any changes on Windows Server?
View 1 Replies
View Related
May 12, 2011
I want to compress as much all packets COMING IN to our network to optimize the bandwidth. When users from Lan accessing the internet, it goes out to our GW1 but I want the RETURN internet packets will go first to Expand 2 for compression then goes to Expand1 for decompression. see attached network diagram setup. All Expand appliances are already configured. What configuration should be in GW1 and R2, both C2851?
View 4 Replies
View Related
May 12, 2011
I want to compress as much all packets COMING IN to our network to optimize the bandwidth. When users from Lan accessing the internet, it goes out to our GW1 but I want the RETURN internet packets will go first to Expand 2 for compression then goes to Expand1 for decompression. Please see attached network diagram setup. All Expand appliances are already configured. What configuration should be in GW1 and R2, both C2851?
View 3 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related