Cisco Application :: C2851 - Configure Router Using Expand Box?
May 12, 2011
I want to compress as much all packets COMING IN to our network to optimize the bandwidth. When users from Lan accessing the internet, it goes out to our GW1 but I want the RETURN internet packets will go first to Expand 2 for compression then goes to Expand1 for decompression. see attached network diagram setup. All Expand appliances are already configured. What configuration should be in GW1 and R2, both C2851?
View 4 Replies
ADVERTISEMENT
May 12, 2011
I want to compress as much all packets COMING IN to our network to optimize the bandwidth. When users from Lan accessing the internet, it goes out to our GW1 but I want the RETURN internet packets will go first to Expand 2 for compression then goes to Expand1 for decompression. Please see attached network diagram setup. All Expand appliances are already configured. What configuration should be in GW1 and R2, both C2851?
View 3 Replies
View Related
Feb 10, 2013
I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies
View Related
Jul 6, 2011
I have a netgear CVG834G main router, were my desktop is plugged on to.I pulled a new cable trough the house and garage to have internet access on the other side (cable length is about 80 meters).After the 80meters of cable I placed a Linksys WRT54GS v5.1 router. The problem is that I can connect to the Linksys, but the Linksys can�t connect to the netgear. On the Linksys the internet LED is blinking very slowly (what does this mean?). So first I thought that the cable was broken or too long. I tested the cable => not broken. I connected the Linksys with the netgear trough a shorter cable and then connected my laptop via the long cable (80meter) and this works perfectly.Is the maximum distends a netgear can take less than 80 meters? (thought is was 100meter ).
View 3 Replies
View Related
Aug 17, 2012
My brother has a router for his house which lives right next door. I am getting wireless through a adapter right now but not good throughout my house.
View 1 Replies
View Related
Jan 16, 2011
Currently We have an RV016 setup and Setup>Network we have the following settings:
Host Name: pagegateway
Domain Name: mycompany.com
Device IP address: 10.20.181.1
Subnet Mask: 255.255.255.0
DHCP Server is not enabled on the RV016. We currently have a Windows 2003 Server that is acting as Exchange Server, Active Diretory, and DHCP Server. My issue is that we are running out of IP addresses and I have about 20 or so left to assign. Given the above setting can I make changes to my RV016 to give me more than 256 addresses? If yes what do I need to do and do I need to make any changes on Windows Server?
View 1 Replies
View Related
May 18, 2011
I have a Dlink Wireless N Xtreme DIR-655 I have run out of port 4 on it to a switch with a cat 5 patch cable that is 25 ft long It is connected to the Internet port on a Dlink 4 port switch. When i run from that on any of the 4 ports back to my computer ( Win7). I get no internet access but if i connect the cable straight from the router there is no problem. I even attempted to use a older dlink router for the switches and no luck there at all. Any reason the internet would not be broadcasting through the switch.
View 3 Replies
View Related
Jul 5, 2012
I cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies
View Related
Sep 29, 2009
I just installed a Linksys WRT160N router. The signal started of good about 50 to 70 feet from the routers location. Now the signal is registering as low to good, about 54Mbps. I was wondering what options I might have to install a wireless bridge for expansion of the signal. I have configured an encrypted network using WPA2. I am wondering what the technical difficulty would be to install and configure it. I setup the WRT160N myself if that means anything.
View 4 Replies
View Related
Aug 16, 2011
My DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
View 1 Replies
View Related
Apr 27, 2012
I just picked up a 24 port Catalyst 2950 to expand my home network and learn a bit more about networking. Having just upgraded the IOS software 'm now trying to get this to work as required on my network but I'm having a few issues.
My intentions are to plug my cable router/modem wan connection which is set up as the dhcp server to fa 0/1, then use fa 0/2 - 24 for the rest of my wired network. So essentially all on the same subnet interfacing with the router 192.168.0.1.
So far I have set up all of the security on the switch, and have all switch ports assigned to vlan1 with no IPs. My laptop connected to fa0/2 however is not assigned an ip address. Looking at a few posts I ahve rightly or wrongly played about with dhcp snooping.
Config
Current configuration : 2205 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
service (code)
View 3 Replies
View Related
Sep 27, 2011
I have a wrt160n that I would like to use to expand the range of my wireless network. I have tried a few solutions, but to no avail. I am thinking I have just not found the proper steps.I am behind a dsl wireless router that Telus has provided me. The values of that router setup are as follows:SSID: TELUS4108WPA/WPA2-AESDefault gateway: 75.156.190.1DNS address: 199.185.220.254Subnet mask: 255.255.255.0
View 9 Replies
View Related
Aug 4, 2011
I have a wireless network in a 2 storey house. The internet access and 1 WRT54GS router is on the 1st floor (using frequency channel 11). The wireless single doesn't do very well on the second floor unless there is a device with a strong antenna. I recently purchased a WET610N Bridge and I have an extra WRT54GS (using frequency channel 1).
I would like to be able to add wireless to the 2nd floor by attaching the extra router to the bridge which would wirelessly connect to the router with the internet.
View 2 Replies
View Related
Aug 20, 2011
I went out and bought a e4200 today and the signal strength is worse than my WGT300n, is there any tweaks I can do to expand my signal strength?
View 3 Replies
View Related
Feb 11, 2013
Do you know if it is possible in ACE 4710 appliance to configure a SIP TLS ?The SIP probe we have in the configuration guide it is only for clear text. for Lync 2013 we need to establish first a TLS session and then within it, send an SIP request..IS it possible in any version? I tried also to configure a HTTPS probe but it fails as it sends a GET which the Lync SIP server doesn't understand.
View 1 Replies
View Related
Oct 11, 2011
I have CSS in single arm deployment model. I want to configure port redirection for the servers. Servers are actually running web service on port TCP 3636. Which is accessibale by VIP http://192.168.200.87:3636 but I dont want to give user this URL I want the user to use standard HTTP URL as mention below, I want user to open http://192.168.200.87 and once they access this URL automatically CSS redirect them to port 3636. How I can achive this. I am using IP addresses for the load balancing.
View 4 Replies
View Related
Jul 3, 2011
I have upgraded gss to version 3.2(0) because I need to track a server that uses only https.I configured a https head KA VIP answer type but the answer never goes on-line.I tried using url... as the VIP address but not go online too.The gss is behind a firewall.I suspected of the firewall but from the gss CLI it seems that the firewall is open for the https traffic: [code]
View 1 Replies
View Related
Mar 6, 2011
How to configure HSRP with Statefull NAT using the application redundancy of the IOS XE? I want to have static NAT using the HSRP groups for clients and SNAT. (I want to achieve this as in normal IOS -[URL] High Availability NAT with HSRP)The configuration that I have on the 1st ASR. The configuration is similar on the second ASR
redundancy
mode none
application redundancy
group 1
name NAT-HSRPIN
[code]...
IP nat inside source static 10.10.10.20 "real ip address" redundancy 1 mapping-id 1 extendable.
View 1 Replies
View Related
Jan 12, 2013
i have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
View 1 Replies
View Related
Sep 24, 2012
I'm looking for some documentation I can share with a customer to explain why I can't configure them a back-up sticky server farm when we're not terminating SSL on the the ACE (we pass SSL from the client through to the rservers, sticking the client to the rserver by source IP address). I've not been able to find anything that addresses this particular scenario in my googling so far. I remember discussing this in my training class with the instructor, but I can't find any reference to it. Have any of you run into this and have a link they can share?
View 7 Replies
View Related
Oct 27, 2011
My ACE module rebooted itself and after the reboot it lost all the config and it has been booted with factory default setting.
[code]....
I would like to know the reason for the same. Is this due to firmware bug? or with the Hardware? I am bit dissatisfied that all of my config vanished without any reason after the reboot of ACE.
View 3 Replies
View Related
Aug 17, 2011
I'm trying to configure Fault Tolerance on a pair of 4710s. I followed the doc, and configured int gi1/4 as the fault tolerance interface, using vlan 12. However the GUI is saying FT Vlan Down
The troubleshooting wiki said check the physical connectivity, but everything there looks good. Each ACE can ping it's own IP, but not the router on that VLAN, or the peer. They're connected to a dedicated VLAN in a switch, and I even tried a crossover cable to directly connect the two. [code]
View 8 Replies
View Related
Apr 12, 2012
Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies
View Related
Sep 18, 2012
I'm configuring ACE 4710's for the first time and I want to load balance my Nuance speech servers on port 554. Here's my configuration on ACE01:
[code].....
View 23 Replies
View Related
Sep 18, 2011
We want to mask part of the path prefix to hide development content: For example: the site(s) are: [URL]However we don't want anything with acme showing...so we would want the loadbalanced url to be: [URL] ...for requests and responses. I think this would be an http re-write request/response scenario?Is this possible to configure this on the ACE Device? We've got the load balance configuration down...not sure how to do this re-write type scenario?
View 2 Replies
View Related
Jan 1, 2013
I'm looking for a way to configure Cisco ACE4710 loadbalancer to bypass traffic that is initiated from server side to Internet?Are there any way to configure this, so that the loadbalancer will not maintain session for this bypass traffic to maximize throughput?
View 1 Replies
View Related
Oct 18, 2011
I'm currently training a group of adults to take A+ soon. I had a question from one of the delegates on the best way to expand the range of a wireless n connection from a router to the rest of the house, WITHOUT using a second WAP.
View 3 Replies
View Related
Jul 25, 2012
I have a US Robotics 8700 NAS (4 bay). I have it running Raid 5. I'd like to buy a bigger shell with more bays to expand the drives. Can I do this easily? Is it hot swappable? If I put the 4 bays in say an 8 drive array, can I add additional drives and will the existing drives work in a different NAS
View 2 Replies
View Related
Aug 2, 2012
I have a network which was recently switched from dsl to comcast. The default network is 10.1.10.1. The dhcp is working with the 5 or 6 installed pc's. All pc's are running xp professional.I inserted the dlink 4 port switch to add a new port by inserting it between the router and a pc.
View 4 Replies
View Related
May 7, 2012
I'm currently using my Acer Aspire x1700 desktop computer running Windows 8. It's connected to my router via Ethernet and gets about 25mb/sec. The problem is, my router can only broadcast the signal to my two front rooms and all of the rooms of the level it's on (Living Room, Sun Room, & Kitchen). All of my devices get full signal in these rooms. The holidays are coming up, so people are going to start bringing cellphones, tablets, gaming devices, etc into my house. My room is about 24 ft away from it (My 2nd floor is 8.5 ft above the 1st). In my room, my laptop, a Dell Inspriron running Windows 7, got about 13mb/sec. But as soon as I walk into the next room, which is about 8 ft away, the signal becomes very spotty on my iPod touch/iPad. My laptop can pick up about 2 bars, and so can my Grandma's HP. If I move another 2 feet into my mom's room my iPod Touch/iPad gets one bar, my laptop still gets two, but it's very slow and spotty. My iPod touch/iPad gets a kind of weak signal in my room.
View 1 Replies
View Related
Jun 5, 2011
I have a D-link DIR-655. Which that along side with my modem is located downstairs. The upstairs living room has a crappy signal where loading videos becomes painfully slow. Awhile ago, I just tried to relocate my router upstairs and just drill a hole for a CAT cable to slip through to the modem downstairs from my room(as my room is directly above the router)...3 useless holes later, for whatever reason it is impossible to drill through. What are my other solutions?
View 1 Replies
View Related
Jan 29, 2011
I have a WAP 4400n and need to expand the range.Linksys support suggested WAP200 to repeat the signal, but I am probably missing something, because its not working.WAP200 can see the WAP4400n, recognizes its MAC adress, but does not work.Anything to set on the WAP4400n to let the signal to be repeated?
View 11 Replies
View Related
Aug 22, 2011
I have a duplex on the first floor have the adsl router from the telephone company can not be replaced,the switch from a cable that comes into a room on the second floor where it was connected to an access point Linksys Wireless-N Access Point with Dual-Band WAP610N the signal on the first floor, however, comes down and in some cases just no signal.
View 3 Replies
View Related
