D-link DIR-655 - Expand Wireless Signal?
Jun 5, 2011
I have a D-link DIR-655. Which that along side with my modem is located downstairs. The upstairs living room has a crappy signal where loading videos becomes painfully slow. Awhile ago, I just tried to relocate my router upstairs and just drill a hole for a CAT cable to slip through to the modem downstairs from my room(as my room is directly above the router)...3 useless holes later, for whatever reason it is impossible to drill through. What are my other solutions?
View 1 Replies
ADVERTISEMENT
Jan 29, 2011
I have a WAP 4400n and need to expand the range.Linksys support suggested WAP200 to repeat the signal, but I am probably missing something, because its not working.WAP200 can see the WAP4400n, recognizes its MAC adress, but does not work.Anything to set on the WAP4400n to let the signal to be repeated?
View 11 Replies
View Related
Aug 20, 2011
I went out and bought a e4200 today and the signal strength is worse than my WGT300n, is there any tweaks I can do to expand my signal strength?
View 3 Replies
View Related
Aug 22, 2011
I have a duplex on the first floor have the adsl router from the telephone company can not be replaced,the switch from a cable that comes into a room on the second floor where it was connected to an access point Linksys Wireless-N Access Point with Dual-Band WAP610N the signal on the first floor, however, comes down and in some cases just no signal.
View 3 Replies
View Related
Jan 19, 2012
I took my router with me to visit family at Christmas. It wouldn't allow the wired computer through the switch, but yet I could talk to the router with my laptop. Rather than reconfigure, I bundled up my router & laptop and let well enough alone.Now that they're all back at my house, I can't reliably get the laptop to connect - Low Wireless Signal error. I've reset the modem & router repeatedly. Tried Channels 1,6, 11 and 8&9 too. n only, as that's my laptop's. On 2 occasions it has connected, rebooted and auto connected and run for 4-5 hours. Then it's gone. I've beat this mess for 3-8 hours per day, for days...!!!Laptop(Vista) connects to every other wifi I've tried. It's sitting 4 ft from the router.
misc. info.
separate dsl modem, Centurytel, Netopia Cayman 3300 series
no other devices beyond wired desktop and laptop
no changes in other neighboring networks
View 9 Replies
View Related
Aug 17, 2012
My brother has a router for his house which lives right next door. I am getting wireless through a adapter right now but not good throughout my house.
View 1 Replies
View Related
Mar 14, 2013
I'm using Windows 7 with a TP Link router and an RCA cable modem. I only have a laptop and I had it set up so I had wireless on it, and was able to get wireless on my smartphone as well. All of a sudden the wireless stopped working and now I can only connect to the internet with the router plugged in to my laptop. I just updated my wireless driver and have tried the 192.168.0.1 thing so many times and nothing seems to work. I also exchanged my router for a new one and that worked for about a week and then stopped working again. This happened once before and it didn't work for a couple days and then I woke up one morning and it worked again.
View 14 Replies
View Related
Jan 21, 2012
Ok, some time this week the strength of my wireless signal has been greatly degraded. I have not had any problems connecting to the router in the past at any location in my house. Now if I am 20 feet away I barely have 1 bar of signal.
I have tried changing channels, and rebooting the router. It has not improved.
View 8 Replies
View Related
Dec 13, 2011
just bought the DIr655 two weeks, everthing was fine except the wireless.almost every day around 6pm the wireless signal are disappear but the internet connection was fine with Lan, and i have to reboot the rounter inorder to get the signal back. i tried update the firmware but it it newest firmware on my rounter.
View 11 Replies
View Related
May 18, 2011
I have a Dlink Wireless N Xtreme DIR-655 I have run out of port 4 on it to a switch with a cat 5 patch cable that is 25 ft long It is connected to the Internet port on a Dlink 4 port switch. When i run from that on any of the 4 ports back to my computer ( Win7). I get no internet access but if i connect the cable straight from the router there is no problem. I even attempted to use a older dlink router for the switches and no luck there at all. Any reason the internet would not be broadcasting through the switch.
View 3 Replies
View Related
Jul 5, 2012
I cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies
View Related
Sep 29, 2009
I just installed a Linksys WRT160N router. The signal started of good about 50 to 70 feet from the routers location. Now the signal is registering as low to good, about 54Mbps. I was wondering what options I might have to install a wireless bridge for expansion of the signal. I have configured an encrypted network using WPA2. I am wondering what the technical difficulty would be to install and configure it. I setup the WRT160N myself if that means anything.
View 4 Replies
View Related
Aug 16, 2011
My DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
View 1 Replies
View Related
Feb 7, 2012
I have been having wireless issues for a while now and decided to buy a TP-Link router to work with this, unfortunately the wrong model was sent out, it's for Cable use only as it is just a router not modem too!I attempted to send it back but as I didn't know it was wrong until I opened it they won't take it back now as I should have checked first apparently.I did some research online and found information that I can use it as my wireless transmitter as long as I use my SKY router as the modem (with it's wireless function switched off).I have attempted the set-up as described in the manual for the TP-Link and I am now speaking to you using the Ethernet port on it, yet none of my wireless devices can see it in the available networks, both the "system" and "WLAN" lights are flashing to say the router is working but I still have no wireless signal.
View 10 Replies
View Related
Jun 24, 2012
My wireless signal strength on my DIR 615 router varies between 57% and 63%. I don't understand why it's not 100%. Is there a way to tweak it up ?
View 2 Replies
View Related
Mar 28, 2013
Region : Venezuela
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP :
I have an issue with my TL-WDR4300 (regular, internet sharing use, no Open WRT or similar things). It was working well, until one day that my devices only receive the 2.4 GHz signal (no 5 GHz) and then I try to connect to 2.4 GHz and it asks for a password. I put my regular password and it doesn't work. Then I tried to bring it to factory default settings, I push the reset button for 8 seconds as the manual points and then same thing. What could I do?
View 2 Replies
View Related
Sep 27, 2011
I have a wrt160n that I would like to use to expand the range of my wireless network. I have tried a few solutions, but to no avail. I am thinking I have just not found the proper steps.I am behind a dsl wireless router that Telus has provided me. The values of that router setup are as follows:SSID: TELUS4108WPA/WPA2-AESDefault gateway: 75.156.190.1DNS address: 199.185.220.254Subnet mask: 255.255.255.0
View 9 Replies
View Related
Aug 4, 2011
I have a wireless network in a 2 storey house. The internet access and 1 WRT54GS router is on the 1st floor (using frequency channel 11). The wireless single doesn't do very well on the second floor unless there is a device with a strong antenna. I recently purchased a WET610N Bridge and I have an extra WRT54GS (using frequency channel 1).
I would like to be able to add wireless to the 2nd floor by attaching the extra router to the bridge which would wirelessly connect to the router with the internet.
View 2 Replies
View Related
Feb 26, 2012
I'm using a router WAG320N in my home but now i need to expand my lan with another ports and wireless coverage.In a wired point (connect directly to the router) i need 3 ehternet ports and a repetear of a wireless signal.The optimal solution woulb be a switch gigabit with an integrated acces point, but I understand that there is no such thing...So going to buyng the switch SE2500 and the AP WAP610N... but then I realized the existence of the bridge WES610N!But the information on the linksys italian site is not enough and the relative page does not works... i need to now if this object can take a wired lan replicate it in 3 ports and expand the wireless network of my router.
View 5 Replies
View Related
Jan 19, 2013
Is possible to setup DIR-655 as a Wireless receiver passing the signal to the other devices by ethernet?
View 2 Replies
View Related
Feb 7, 2013
Region : Others
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
I bought today new TP-Link TL-WR740N and I connected it with my cable modem as it is in manual instructed. There is problem with outgoing signal from router. It is about 1/10 from it should be (it is around 2Mbps from 20 Mbps). Same speeds are going out from router through LAN port and WiFI signal.
View 6 Replies
View Related
Dec 14, 2011
I have a dir-655 xtreme N gigabit router with 2.03NA version firmware. The wireless signal will suddenly and randomly disappear from my laptop. I checked the properties of the network connected it remains on the same channel when it reconnects so I figure it's not a channel issue.I have reviewed this forum for hours and have made many changes to my settings, but nothing seems to keep the wireless signal from stopping.
Computer: dell inspiron 6400
OS: windows XP pro (sp3)
ISP service: DSL
Modem: stand alone (Sagemcom 4300)
Router: dlink / xtremeN gigabit router / dir655
Set for mixed g, n and b wireless mode
Security: wpa-personnal / TKIP
Firmware: version 2.03NA
View 14 Replies
View Related
Mar 15, 2013
Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Fullrate
No matter what I try, the signal strength never gets better that 30%, even when I have my laptop next to the router. I have tried various settings (found in these forums), but nothing seem to work. My old D-Link performed better, both close and over distances.
View 2 Replies
View Related
May 14, 2013
Region : UnitedStates
Model : TL-WR841N
Hardware Version : V8
ISP : ATT
I get this new router TL-WR841N from amazon.com, I get no signal/internet connection on my computer when I install/connect the router using the installation min CD (same procedure at listed here: url...The DSL connection is good, since I get internet connection when I connect my modem directly (without the router) to my computer. My modem is the old Siemens SpeedStream 4100 with IP Address of 192.168.0.1 from ATT.Is my router deficit ?
View 2 Replies
View Related
May 31, 2011
I have recently had to deploy a 1410 in a Root/Non-root bridge configuration to expand a terrestrial network across to an uncabled area.
All switches in play are 2960 series and the bridge is running with multiple Vlans.
Basic config as follows.
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname BRIDGE001!no logging consoleenable secret 5(code)
View 1 Replies
View Related
Jan 2, 2013
Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?
View 5 Replies
View Related
Jan 31, 2013
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
View 1 Replies
View Related
Apr 18, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : HughesNet
I received this router today, I have a MacBook Pro and a iPhone. The router came with a very small cd, I was very disappointed because , when I purchased this router from amazon , the discription read that this router is Mac compatiable. But that is not true if the cd is not compatiable! My problem is I get a good signal for wifi, but I can not open any websites with my Mac or my iphone.
View 1 Replies
View Related
Dec 28, 2012
Region : Canada
Model : TL-WR700N
Hardware Version : V1
Firmware Version : latest
ISP : various
What would seem to be an ideal way to share a hotel wifi signal with other devices, would be:
Laptop signs into hotel/resort wifi and completes sign-in page. Share wifi signal with TP router via an ethernet cable. TP router acts as hotspot for connection by other devices. This is the method this Apple based article suggests:
[URL]
I have tried this with Windows 7 using a bridge between the laptop wifi and lan adapters. But I must be doing something wrong.
The other option is to use ICS, but not sure then if the hotel's system would see additional devices. (we are limited to 4 where we stay, but exceed that when family visits!)
View 9 Replies
View Related
Mar 24, 2013
Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : Build 121225 Rel.37950n
I have low signal range from this WDR4300 router on both bands and especially on 5Ghz i lose my connectivity on just few meters away from the router and on other rooms in my 80m2 apartment, i also own another tp link 740n with only one antenna and the range is better with it almost covers all my apartment. Router has been reset after being updated to latest firmware and tried different configurations but im not satisfied with the signal range. Is there something i can do.
View 1 Replies
View Related
Oct 18, 2011
I'm currently training a group of adults to take A+ soon. I had a question from one of the delegates on the best way to expand the range of a wireless n connection from a router to the rest of the house, WITHOUT using a second WAP.
View 3 Replies
View Related
Jul 25, 2012
I have a US Robotics 8700 NAS (4 bay). I have it running Raid 5. I'd like to buy a bigger shell with more bays to expand the drives. Can I do this easily? Is it hot swappable? If I put the 4 bays in say an 8 drive array, can I add additional drives and will the existing drives work in a different NAS
View 2 Replies
View Related
Aug 2, 2012
I have a network which was recently switched from dsl to comcast. The default network is 10.1.10.1. The dhcp is working with the 5 or 6 installed pc's. All pc's are running xp professional.I inserted the dlink 4 port switch to add a new port by inserting it between the router and a pc.
View 4 Replies
View Related
