Linksys Access Point :: WAG320N / Expand LAN With Another Port And Wireless Coverage

Feb 26, 2012

I'm using a router WAG320N in my home but now i need to expand my lan with another ports and wireless coverage.In a wired point (connect directly to the router) i need 3 ehternet ports and a repetear of a wireless signal.The optimal solution woulb be a switch gigabit with an integrated acces point, but I understand that there is no such thing...So going to buyng the switch SE2500 and the AP WAP610N... but then I realized the existence of the bridge WES610N!But the information on the linksys italian site is not enough and the relative page does not works... i need to now if this object can take a wired lan replicate it in 3 ports and expand the wireless network of my router.

View 5 Replies


ADVERTISEMENT

Linksys Wireless Router :: Wrt600n Expand Wifi Coverage

Aug 16, 2011

My DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
 
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?

View 1 Replies View Related

Expand WiFi Coverage - Over Large Area Like 4 Or 5 Access Points

Oct 22, 2011

expanding my WiFi coverage over a pretty large ares like 4 or 5 access points.

View 3 Replies View Related

Linksys Access Point :: Using Wireless G WAP54G To Extend Coverage?

Jan 29, 2012

I have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?

View 1 Replies View Related

Linksys Access Point :: Best Way To Expand Signal WAP610N

Aug 22, 2011

I have a duplex on the first floor have the adsl router from the telephone company can not be replaced,the switch from a cable that comes into a room on the second floor where it was connected to an access point Linksys Wireless-N Access Point with Dual-Band WAP610N the signal on the first floor, however, comes down and in some cases just no signal. 

View 3 Replies View Related

Linksys Wireless Router :: E4200 Access Point To Maximize Coverage Throughout House

Jan 27, 2012

I bought two E4200s with the intent of using the second as a wireless access point to maximize coverage throughout my house. I just learned the hard way that the E4200 doesn't support that feature, and will only act as an access point if physically connected to the primary router that is connected to the internet.
 
Before I spend even more money on equipment, I was wondering if any of the experts here can tell me whether I can use a Linksys Bridge, like the WET610N or WES610N, to operate the second router in bridge mode and turn it into a wireless access point?

View 9 Replies View Related

Linksys Cable / DSL :: WAG320N As A Wireless Access Point?

Dec 14, 2010

I have to change ISP, as mine is closing down , and the new ISP will be sending a N router - which may have 5Gh - so I'm thinking of replacng a "G" AP with the WAG320N and use the 5Ghz range. The WAG320N will be used with a USB Music harddrive and a TV and PVR connected to it - so my music will be direct to the DLNA devices - and also provide any devices with a 5Ghz signal

View 9 Replies View Related

Netgear Router Setup To Expand Wireless Coverage?

Aug 17, 2012

My brother has a router for his house which lives right next door. I am getting wireless through a adapter right now but not good throughout my house.

View 1 Replies View Related

Cisco Wireless :: Access Point Coverage Area 1042

Apr 6, 2012

I want buy an Access point which cover 300 Meter coverage Area.
 
Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.

View 8 Replies View Related

Linksys Access Point :: WAP54G LAN Port Support Wired Computer Connection

Jul 7, 2011

When the WAP54G is set up as a repeater for a WRT54G, will a computer connected to the LAN port on the WAP54G be able to connect to the network? I know it will see the WAP54G if I manually set it's ip address.
 
I guess I want it to act as a wireless NIC for the desktop while also operating as a repeater. Is this possible? If not, will one of the other AP settings like Bridge allow the wired connection to connect to the other side of the network and give wireless access to wireless devices? I've hacked up and attached one of Linksys's diagrams to show what I'm trying to do. It seems to me the easiest thing to do would be to buy a wireless NIC for the desktop.

View 5 Replies View Related

Linksys Cable / DSL :: WAG320n UDP Not Working On Port Forwarding?

Dec 5, 2011

I have some hardware on my internal network which I want to send udp packets. I can connect using telnet to it prooving that TCP and port forward works but when I try to send a UDP packet externally it fails.I can however send the same packet internally and port forwarding works fine.My router is Linksys by Cisco WAG320n.

View 2 Replies View Related

Linksys Cable / DSL :: WAG320N Port Forwarding / DMZ Not Working

Mar 4, 2011

I'm trying to open some ports for my webserver, I've configured the static IP and forwarded port 80 to my server's IP and I checked the port on canyouseeme.org and it says it's closed. I've tried multiple ports (21, 22, 7878 whatever) and all do the same thing.
 
So my next step was to try DMZ on the server's IP .. still no happiness .. ports stay closed. I checked this on multiple computers and it still won't open any ports for any machines on my network.
 
Updated to the latest firmware .. didn't make a difference. My ISP doesn't block any ports (didn't have any issues on my old router.

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N Set First Ethernet Port To WAN And Got Connection

Apr 4, 2011

Got BT Infinity installed today, thought I would ditch the Home-hub 3 and go back to my tried and tested WAG320N. Got it configured, set the first ethernet port to WAN and got a connection.Ran speed test.net and comes out at 26Mbit.using the Home-hub 3.0 I get 37.5MBit.

View 4 Replies View Related

Linksys Cable / DSL :: Connect 2 Hard Disk To Usb Port Of WAG320N?

Oct 14, 2011

can i connect 2 hard disk to usb port of my WAG320N or one hard disk and one printer?

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N Restrict External Port Traffic

Jul 9, 2011

I have recently purchased a Linksys WAG320N (firmware V1.00.12) to replace my old ZyXEL P-660H-D1.I've managed to set it up roughly the same in terms of the ports I want open and port forwarding, with one exception: I can enable a port to be forwarded to an IP address on my network, but I can't find anywhere to set it so that the port is only allowed from a specific IP address outside of the network, e.g.
 
Accept port [some number] from [some Internet address] into 192.168.1.2 but reject attempts from others.I thought it might be in Access Restrictions but that only covers internal IP addresses.

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N Routing Ports For Getting Port 21 To Route To 786

Feb 16, 2011

i am trying to get my router to change ports for certain tasks for eg FTP Port 21 i dont want to use 21 and telnet Port 23 i dont want to use 23 ,is there a way of routing ports so that i can get port 21 say to route to port 786 instead so i can ftp from port 786 and so and and so forth

View 3 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Linksys Cable / DSL :: WAG320N - Router Opens The Port And Close It After A Couple Of Hours?

Feb 9, 2010

I have noticed that in my router log that the router opes a port automatically without any human interaction and after some the time router closes the port again.Here is the log file of my router that opens the port and close it after a couple of hours. 
 
LOG------------------------------
 Tue, 2010-02-09 10:02:16 - AddPortMapping: external NULL:3658 to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP) with timeout:0Tue, 2010-02-09 10:02:16 - no permission rule matched : accept by default (n_perms=0)Tue, 2010-02-09 10:02:16 - redirecting port 3658 to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP)Tue, 2010-02-09 10:02:16 - creating pass rule to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP)
 .....
Tue, 2010-02-09 12:52:59 - DeletePortMapping: external port: 3658, protocol: UDPTue, 2010-02-09 12:52:59 - removing redirect rule port 3658 UDPTue, 2010-02-09 12:52:59 - Trying to delete rules at index 0

View 6 Replies View Related

Cisco Wireless :: Wap200 Access Point Configuration / Port Disabled

Mar 27, 2012

I have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Setup After A Reset?

Jul 9, 2006

I had to reset my access point but the login screen fails to appear to lock the router.  I don't have the setup wizard disk.

View 9 Replies View Related

Linksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point

Jan 17, 2013

I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?

View 1 Replies View Related

Linksys Access Point :: WRT320N Access Point Vs Range Extender

Dec 14, 2011

Have a WRT320N router at one end of the house in the basement.  Would like to boost signal to other end of the house.  Which product should i use, an access point or a range extender?  My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.

View 1 Replies View Related

Linksys Access Point :: WAP4410n MIBs Or OIDs For Access Point

Jul 3, 2012

I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?

Apr 25, 2011

I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
 
 The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
 
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
 
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.

View 3 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Cisco Switches :: SG-200 Access Point Is Only Able To Access Internet / When It Is Plugged Into Port

Jun 22, 2012

I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]

View 4 Replies View Related

Linksys Cable / DSL :: Getting Access To External HDD With WAG320N?

Feb 6, 2011

I have WAG320N. I attached External HDD to Router's USB.I don't  know how to access to HDD and other users also..(not via internet)

View 1 Replies View Related

Linksys Access Point :: Repeat WAP54G Access Point?

Aug 25, 2011

What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G. 

View 4 Replies View Related

Linksys Access Point :: WRT120N - Cannot Connect To An Access Point

May 10, 2013

I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
 
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.

View 1 Replies View Related

Linksys Access Point :: Configure WRT120n As An Access Point?

May 1, 2012

Is it possible to configure WRT120n as an access point?

View 1 Replies View Related

Linksys Access Point :: E3000 Configuration As Access Point?

Apr 6, 2011

I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.

View 1 Replies View Related

Linksys Access Point :: Way To Find Mib For WAP54G Access Point?

Feb 10, 2012

I have tried to find mib for my Linksys WAP54G acces point  without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved