Linksys Access Point :: WRT120N - Cannot Connect To An Access Point
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
ADVERTISEMENT
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Sep 21, 2011
I am currently using a Linksys E2500 router and cannot get a strong enough signal to an upstairs bedroom for my wife's iPad 2. I have a spare Linksys WRT120N that I would like to utilize to increase the signal upstairs. There is no way I can run a CAT 5 cable to that room. I believe both routers have WDS.
View 5 Replies
View Related
Jan 14, 2011
I am using a linksys WRT120N router as a Access point in my student dorm (according to the rules!). As long as i used it as a router, I never had problems with the speed. But now, the connection is very slow.For example, when I am wirelessly connected to the AP, and when I ping the main router of the building, I see packet drops and some packets have more than 4000ms rtt. (while normally it should be b/w 0 and 1 ms). So as I understand it, there is some problem between the AP and my computer in the wireless channel or something but I have no clue.I am using the latest firmware from the CISCO website.
View 1 Replies
View Related
Jun 5, 2012
I have a WRT120N I would like to convert from a router to a Wireless Access point. Can this be done and how would I do this?
View 4 Replies
View Related
Jul 19, 2011
I bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
- how i configure my WAP4410N as a repeater?
- is there any settings that i must set on the WRT120N, before combining the WAP4410N?
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Jul 25, 2012
I want to configure and WAP610N to work as an Access Point (it was configured by previous administrator some time ago): free hotspot open, LAN secured by password. What makes my last 2 days horrible is that I can't even get access to Administration Panel. Used Cisco Online Support Articles, used User Manual, tried many ways to connect without luck.First of all I've connected LAN cable directly from PC to AP and Windows stuck at "Identyfying State", after some hours "arp -a" command shows me only IP's of my LAN, no MAC of the AP.Tried to reset settings to the factory default - when on push for 30 seconds reset button, power diode blinks, ap starts and settings are the same - still connects to the company's LAN.Wireless networks is default 'linksys' without password I can connect to it and get the internet, after pushing fast connection button it changes to secured "Linksys-<some letters and numbers>" to which I can't connect.I can't even get IP on wired and wireless connection - DHCP don't work? I don't know what IP to set manually. How can I get access to Administration Panel? How to reset this thing?
View 4 Replies
View Related
Feb 19, 2011
My Linksys Range Extender died. So I bought a WAP54G thinking that I could use it as a repeater to extent the range of the signal from my router to the other wireless PCs in the house.
1st floor:
PC1 connected to a WRT54G v.5 router
PC2 connected to PC1 router via USB network adapter
Laptop connected to PC1 royter via internal wireless
2nd floor
PC3 connected to PC1 router via USB network adapter
PC4 connected to PC1 router via USB network adapter
The main goal is to set up the WAP54G in between PC1 and the other PCs to extent the range of the signal particularly to the 2nd floor PCs.The instructions for configuring the WAP54G are fairly straightforward, but the first issue I run into is not being able to connect to the WAP54G web setup. I am using the following instructions:
[url]...
once I configure or setup the WAP54G through another PC as a repeater, will I be able to disconnect it from the PC and use it as a standalone (e.g., plugging only the power in and leaving it in my kitchen or a hallway) to extend the range of the signal? Or does it have to stay connected to PC1 and does PC1 always have to be on for this WAP54G to act as a repeater?
View 2 Replies
View Related
Dec 4, 2011
How do I connect three or more WAP54G's in bridge.
View 3 Replies
View Related
Jan 7, 2012
iPhone does not recognize home network. MacBook does! The phone recognizes and connects to all otther networks except this one at home.The WAP610N is used as an extender attached to Alcatel Lucent 7130.
View 2 Replies
View Related
Dec 14, 2012
Even using the static address I cannot connect to the unit's set up page.
View 1 Replies
View Related
Feb 20, 2011
I am unable to connect wirelessly to a WAP54G v2 with a Dell Inspiron 17R/N7010 running Windows 7. In fact, previously a relative's laptop, also running Windows 7, was also unable to connect at my location.The access point has no security enabled. It shows up in the list of available wireless networks. I've configured the wireless adapter properly (static ip). Yet connection fails. Windows suggests that I power cycle the access point and try again. If I use the same configuration for the wired connection, it works. Is there a compatibility issue with Windows 7 and the WAP54G v2?
View 6 Replies
View Related
Dec 9, 2011
I've some strange things with my WAP610.I connect it to my lan, my DHCP server assign an IP, that's normal way..I lookup for this IP, and fill in the address field in my IE (firefox or safari I've tried all of them).... the AP ask me password and user... I fill in the password field... and get into config...
So I think it could be a bug with static IP... I'll try on the wireless security... select "manual"... change nothing (leave default value) click save... wait a while... connect on the DHCP ip, return to the wireless page... and lost a lot of time since nothing is saved.
View 7 Replies
View Related
Jun 12, 2007
Cannot access configuration page for WAP11 Access
View 9 Replies
View Related
Oct 12, 2011
1. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
View 3 Replies
View Related
Feb 25, 2011
I have a linksys wrt54g ethernet wired to my router. I got a wap54g and don't know a thing about either. I hooked up the wrt54g years ago with linksys assistance. I thought I could just hook up a wap54g with ethernet to the directv dvr and the two would talk.
View 2 Replies
View Related
Nov 19, 2012
iPhones and iPad don't want to connect.
View 1 Replies
View Related
Nov 29, 2011
I just purchased a Toshiba Thrive tablet and I can't get it to connect to my wireless router. My router (WRVS4400N) works flawlessly with my laptop and desktop. I have spoken to a Cisco tech rep and they assured me that there is not a compatibility problem with the WPA-Personal setting I am using. When I speak to a Toshiba tech they tell me I have a router conflict. To verify this I went to my local Starbucks and low and behold it logged right on with no problem (The Starbucks system was not a protected system). This confirms to me that there is a conflict between the router and the tablet.
View 1 Replies
View Related
Feb 22, 2011
Whenever I try to connect my iPhone 4 or iPod Touch 3rd Gen it says incorrect password. I have confirmed that I am using the correct password and have also tried putting a $ before the password.
View 2 Replies
View Related
Nov 16, 2011
we have 2 Access point WAP610N. The after some time goes in stand by and we doesn't able to connect to it. We updated at last firmware (1.0.02 build 3, Feb 25, 2011 ) Timeout inactivity 3600 Renewal key 600 Protection WPA2-PERSONAL
View 1 Replies
View Related
