How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 RepliesI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedWhich AP's Wap200 can bridge with this ?
View 1 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View Relatedhow is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View RelatedI have two Cisco AP 1242G and i'm trying to configurate a Point-to-Point Bridge Configuration to connect two wired LAN. Figure 1.8 [URL] I would connect two wired networks.
I tryed two configurations: Root and Non-Root AP. This way every wired PC on the Root AP can connect to the Access points, but cannot connect to the wired PC on the Non-Root AP.AP and WGB. Even this way the wired computers on one AP cannot connect to the wired PC on the WGB. This way only the wireless client can connect to the wired network. This is my network:
Root Bridge Non Root Bridge
10.0.0.1 10.0.0.2
Wired clients on the RB Wired clients on the Non RB
10.0.0.100 10.0.0.200
Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".
View 16 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedThis is the first outside bridge I have ever attempted. These radios are 2000 feet apart, pointed at one another. The first radio has a cat 5 (with POE) to a Windstream 2Wire wireless router.
The other radio has 3 RadioLabs AP's (with POE) connected to it. I have followed the installation guide for the GS200 ( Here) to no avail. I must have missed something but don't know what.
I have 2 cisco 1941/K9 vpn router. I have configured both with LAN ip address given by our vpn provider which is 172.10.10.1 and the other is 172.10.20.1. Both IP addresses are configured to GigabitEthernet port 0/0 on both routers.
1. Is it possible to configure our own set of ip address like 10.71.10.1 and 10.71.50.1 on the GE 0/0 port?
2. Or can we configure our own set of ip addresses (10.71.10.1 and 10.71.50.1) to GigabitEthernet port 0/1 and maintain the other ip addresses on port 0/0?
The first purpose is to have our own set of ip addresses for LAN connection and I will be able to connect or telnet whichever ip address or port is up.
Currently in place ISP WISP Point to Point network would like some pointers to exceed in doing it right. Here are some issues.ISP Fiber 50 Megs down and 50 Megs up ( Working )What Router do I use? Looking at Cisco RVS4000 at JDT Site as main router I have routers at others towers using the 10.1.19.xxx address as wans setup.Do I pull out all routers and use only one from the JDT Site?
a. Due to Port forwarding
b. Lets say main Wan is 74.144.55.159 Lan 10.1.19.1
1. Site BTT router is assign address 10.1.19.33 Lan 192.168.6.1
a. Can I setup 74.144.55.159:85 to see 10.1.19.33?
My Point ot Point radio use different IP address to separate from lan address (10.1.19.xxx) Radios (10.1.119.xxx)1. Everything is working just want to re-design everything never thought I would grow this fast with in 2 years. Hope I explain this well enought. 90% of users are out in the country without high speed internet.
I have a point to point 100mb line connecting SG500x switches at 2 locations, with these ports in a vlan together. I use layer 3 on the SG500x's to route between the two sites. I also have RIP protocol enabled to allow for automatic failover if the point to point fails (this works well).
I upgraded the ios to 1.30.59, and the connection now runs at a fraction of the speed. I have hard-coded the ports to run at 100mb full duplex, but I still only get around 12mb of throughput between the switches. I used to get about 90mb before. The provider also hard-coded the circuit to 100mb full duplex. The provider has checked the circuit remotely, and everything looks fine. I tested with a laptop at each side, and did get almost 70mb throughput. I would think this indicates some type of setting mismatch, but i cannot find anything.
I am using a backup vpn for now as some things look flaky as well (on vpn, I can use the web interface to access the SG500x on the opposite side, but on the point to point I cannot - I can ping the device though).
I have seen some references on here to shutting off STP on these 2 ports.
How do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?
View 1 Replies View RelatedI all we are going to terminate point to point link between 3750 and 6506.
on 6506
int gi1/45
no switchport access
ip address 192.X.0.x 255.255.255.0
no shut
[code]....
Does this config correct as i am configuring between stack switch and 6506
We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View Relatedrecently i just connected a non cisco ip phone(from panasonic) to Cisco 2960 POE switch at site A. The PABX system is located at site B,Site A and site B are connected using MetroE Point to point.I would like to apply QoS for voice vlan. I want to assign 2MB to the point to point connection for voice vlan.
View 3 Replies View RelatedI have 2 Cisco Catalyst 6509 switches connected directly using direct point to point link.The OSPF is configured for point - point link.The currently the interface is down administratively.I will unshut the port . After that i would like to know how much time will it take for the ospf to establish the neighbour relation.
View 5 Replies View RelatedI would to realize an point to point connection in L2TPv3 with a bandwidth pass through of 1 Gb. Which routers/switches I can use?
View 3 Replies View RelatedWe have a MWR2941 (running 12.4(20)MR) router on site A and one in site B which will be connected over a Service provider L2VPN Ethernet over MPLS (EoMPLS) Network, with 10Mb Bandwidth allocated by the ISP. I have simulated this in the lab by directly connecting the two MWR's back-to-back via the Gig0/0 interface with configurable bandwidth of 10Mb on the Trunk interface.
The E1 TDM pseudowire end to end is working fine, with PTP configured for E1 timing/clocking. In addition I have a 2960-24PC-L switch connected on G0/2 of the MWR (on each end) configured with dot1q trunking. The switch will be used to connect two user groups in two seperate vlans (VlanA and vlanb) and transported across the same 10MB wan Link. Below are the requirements
1) Classify and mark Psuedowire packets E1-DATA coming from a E1/CEM interface and give it priority treatment over the WAN Link with reserved bandwidth of at least 4MB
2) Classify and mark Signalling/Timing PTP packets coming from PTP Vlan and give it strict bandwidth reservation over the WAN Link of 1MB
3) Classify and mark vlan A traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
4) Classify and mark vlan B traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
It is important that the E1 Traffic and the Signalling/Timing PTP packets are given priority and strict reservation so that it is not dropped in times of congestion. At the same time Vlan A and Vlan B need bandwidth reservation to give them their guaranteed bandwidth.
Currently I have tried applying policy map to the CEM interface. However, I am having trouble matching anything on the CEM input. Also I am having trouble applying a service-policy outbound on the gig0/0 (WAN Link). Also I can’t apply a service-policy inbound on the Gig0/2 interface with match statement. I have tried configuring input policy map to classify and mark PTP traffic (Vlan 902), but the MWR does not also allow me to attach a service-policy to the vlan interface. how to configure the MWR and have a workable QOS solution.
i have cisco 3845 router,how to configure vrf for point to point link .
View 1 Replies View Related