Cisco :: Does WLC 2500 Series Supports 1262 Series Access Point
Jun 14, 2011Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 RepliesDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replieswhich differences exist between 7.0 and 7.2 firmwares? I have to decide/choose which of them to run, before continuing to configure my WLAN infrastructure.
View 3 Replies View RelatedI have Cisco Wireless Controller 2500 series (AIR-CT2504) and 10 LAPs implemented in my office building. I need to enforce security policy.
I have few questions below regarding the Wireless controller 2500 Series.
1) Can i enforce Internet security policy such that all prohibitive sites remain block from the WLC?
2) Is it possible to allow Internet access to only designated machines/users ?
3) Initial logon page for user /machine authentication to get access to wi-fi ?
I need the MIBs for Cisco 2500 WLC. I have it for 5508 WLC. Does it works same for 2500 WLC too ?
View 1 Replies View RelatedI recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.
View 1 Replies View Relatedlinks with information / guidelines for the initial setup for this Access Point?
View 7 Replies View RelatedI have the problem with machine authentication, our customer using Wireless Controller 2500 Series and need implement machine authentication on IAS server. So, as my understand is our controller may not change anything with configuration but we may configure IAS for support machine authentication, correct? but my question is how to? and is it work ?
View 24 Replies View RelatedI have 2500 series wlc which is crashing again and again. I attach the log of crash as well.Also in License location the base-ap-count license " is not in use ".
View 3 Replies View Relatedhow to connect macbook air with cisco 1100 series access point
View 2 Replies View RelatedAccess point gives all junk vlaues in console. I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes
View 2 Replies View RelatedThe products from SRP 540 series line (541w etc) will ever support IPv6 features or remote VPN (eg SSL VPN or Cisco QuickVPN)? If yes, is there a time horizon?
View 6 Replies View RelatedI tried looking in ASA documentations but unable to find out that how many IPSec Tunnels can be terminated to an ASA cluster. I have 5545 running only two IPSec Tunnels so far but need to terminate 18 sites all up and would like to confirm how many tunnels we could terminate? Is there a limitaion to it?
View 2 Replies View RelatedDo you know if the new 2500 series controller supports things like mobility groups? Could I use 2 of these and do inter-controller roaming. Also do you know if this would work with a 2106 controller and a 2505 controller or are they 2 completely independent controllers only knowing about their own APs??
View 12 Replies View RelatedI want to download the Cisco 2500 Series Wireless Controllers Release 7.3 Software AIR-CT2500-K9-7-3-112-0.aes.I have CON-SMB for it, when I try to download it I am not to download it. I have mentioned the message given by Cisco" The category for this contract does not include the feature or the benefit for software download that you are requesting at the moment, this means that even if the contract is a support assistant (8X5XNBD) does not support the the mentioned feature for you to update the device you need, please refer to your partner directly to be able to acquired a Cisco Service Contract that supports and include the software download feature to be able to upgrade and update your device as you need."Is there any seprate contract for downloading the Software.
View 2 Replies View RelatedDoes 2500 series wireless controllers support redundancy?
View 1 Replies View RelatedI noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?
View 8 Replies View Relatedwe have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View Relatedi access points in our network.I want to connect with 3550 switch but access point is not working and getting the below error
controller port error.
IOS image --=c3550-i9q3l2-mz.121-20.EA1a.bin
Switch Model---WS-C3550-24PWR-SMI
I want to know ,this access point is supported on this switch ?
I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode. see the below picture
I have disabled the multicast globally from CLI. config network multicast global disabled
disabling the multicast so that i can set the access point in HREAP mode.
I have a customer whom has six LAP1131AG-K9 but no controller and they are interested in one of the new 2500 series, specifically a AIR-CT2504-5-K9 with a 5 AP add-on license to bring total AP capacity to 10. I can't determine clearly if this controller will work for these older AP's prior to them making the jump to 802.11n via the 3500 or 3600 series, looking to the community to confirm.
View 3 Replies View RelatedI am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.I got 2500 WLC with POE switch and 4 aironet AS 1142.
View 16 Replies View RelatedI am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.
I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.
In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.
I got 2500 WLC with POE switch and 4 aironet AS 1142.
Looking for some training on the 2500 series controller and 1142 or 1040 AP's preferably.
View 10 Replies View RelatedI recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies View RelatedMy access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.
View 2 Replies View RelatedI am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View Relatedwe are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
how many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies View RelatedCan Controller 4400 series work with Aironet 3600 series?
View 5 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View Related