Cisco Wireless :: Configuring Access Point Of 1200 Series?

Apr 19, 2012

I recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.

View 1 Replies


ADVERTISEMENT

Cisco Wireless :: Change IP Address Of Aironet 1200 Series Access Point

Dec 30, 2012

we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.

View 17 Replies View Related

Cisco :: Configuring 1200 Access Point / Vlans

May 29, 2012

I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
 
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan? I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
 
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan?

View 6 Replies View Related

Cisco Wireless :: 1200 Connecting Access Point With Configuration Required

Apr 30, 2007

I have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???

View 2 Replies View Related

Cisco :: Does WLC 2500 Series Supports 1262 Series Access Point

Jun 14, 2011

Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9  Access Point? How can I check this?

View 1 Replies View Related

Cisco Wireless :: Using Both Radios On 1200 Series AP?

Jun 7, 2012

I am using 5 Cisco 1200 Series APs with both an A and G radio. Is there a benefit/problem to running both simultaneously? I would have one SSID and is setup for Fast Roaming as well.

View 1 Replies View Related

Cisco Wireless :: Subnet Not Getting To The Internet With 1200 Series APs?

Dec 3, 2012

I have a office network that was setup before I started. We have a 172. subnet and a 10.2 subnet. When users on Wifi get a 10.2 address ( ran out of 172 address )  they are not able to get out to the internet. But if the laptop is  connected to a LAN port and get a 10.2 address they are able to get to  the Internet. Not sure if its the Aps I need to configure or the Pix seeing that if they get a LAN address of 10.2 everything works. This is becoming a bigger issue now that the company has out grown its main subnet  (172.)  
 
APs= AIR-AP1231G-A-K9
Vlan = 172.16.1.XXX
Vlan2=  10.2.0.XXX
Hardware:   PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz

View 9 Replies View Related

Cisco Wireless :: Radio Supported For 1200 Series?

May 15, 2012

I am running the upgrade tool on Aironet AP1230B-A-K9. I can't join the controller by using the upgrade tool. the error is "AP does not have Supported Radio". What radio is the upgrade tool or controller look for on Aironet 1200 series? This AP is running 802.11b. However, I have several APs which the same model is running on the same one controller.  The controller is model 4402.

View 8 Replies View Related

Cisco Wireless :: Register Ap Aironet 1200 To WLC 5500 Series?

Nov 20, 2012

I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap,  but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.

View 6 Replies View Related

Cisco Wireless :: Configuring Root Access Point And Repeater In 1252-AG-A-K9?

Dec 19, 2011

how to configure Cisco 1252-AG-A-K9 Access Point Root and Repeater?

View 9 Replies View Related

Cisco Wireless :: How To Connect Macbook Air With 1100 Series Access Point

Oct 10, 2011

how to connect macbook air with cisco 1100 series access point

View 2 Replies View Related

Cisco Wireless :: 3602i Series Access Point Gives All Junk Values

May 16, 2013

Access point gives all junk vlaues in console.   I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes

View 2 Replies View Related

Linksys Access Point :: Configuring WAP54G With Existing Netgear Wireless?

Apr 26, 2013

Having some problems connecting up my "new" AP My current set-up consists of a Netgear "Virgin Superhub" cable modem/wireless router, a ZyXEL WRE2205 (repeater) in the hall on the first floor, and Ethernet connections through to a number of rooms, including the loft. I can't get wireless access in the loft, and I want to put the AP up there, connected through Ethernet. I want to use the same SSID and security for the AP as on the router and repeater so I can roam around(!) That's possible isn't it?What I've done so far (which hasn't worked) is connected via laptop to AP, set AP into AP mode(!), set the AP to dynamic IP, set the SSID / security the same as the router/repeater, plugged the AP into the Ethernet and tried to connect.

View 7 Replies View Related

Linksys Wireless Router :: E2000 - Configuring Second One As Repeater Access Point

May 28, 2011

I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.

View 2 Replies View Related

Cisco Wireless :: Configuring DHCP Reply-agent On 1142N Access Point

Feb 27, 2012

configuring DHCP on access point, i have cisco 1142N access point, in my network.. working in autonomous mode, i have assigned a static ip to access point with default gateway.. from AP i'm able to reach internet and user connecting to access point are not able to get ip.. i have DHCP server in my network. how to make access point to fetch ip from my dhcp server and assign the saem to client.

View 10 Replies View Related

Cisco Wireless :: 3600 Access Point Series Will Get An Add-on Module To Support 802.11ac

Oct 23, 2012

I noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?

View 8 Replies View Related

Cisco Wireless :: 3500 Series Access Point Is Not Working On WS-C3550-24PWR-SMI?

Jan 17, 2013

i access points in our network.I want to connect with 3550 switch but access point is not working and getting the below error
 
controller port error.
 
IOS image --=c3550-i9q3l2-mz.121-20.EA1a.bin
 Switch Model---WS-C3550-24PWR-SMI
 
I want to know ,this access point is supported on this switch ?

View 17 Replies View Related

Cisco Wireless :: Disable AP Mode Multicast In 1231 Series Access Point

Jan 23, 2013

I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode. see the below picture

I have disabled the multicast globally from CLI. config network multicast global disabled
 
disabling the multicast so that i can set the access point in HREAP mode.

View 3 Replies View Related

Home Network :: Configuring Access Point Tplink TL-wa5110G With Wireless Router?

Jan 3, 2013

I have a tplink acess point TL-wa5110G . I have WISP ( wireless internet service provider). I have configured the acess point on wisp client router mode and wan type to pppoe gave the username and pwd..Now i want to share internet wirelessly. now my question is that can i connect the aces point to wan port of the wirless router to share internet wirlessly? Because i have seen the instruction figure in tplink access router where they have shown that u can connect it with with unmanage able switch to share it to wired lan.i want to ask can wirless works to share internet if i use wireless router to access point.

View 1 Replies View Related

Cisco Wireless :: 3502 Access Point Will Not Connect To 4400 Series WLAN Controller

May 20, 2012

I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect.  But I am not having any luck getting into a controller.  Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.

View 10 Replies View Related

Cisco Wireless :: Access Point 1042 Series In Light Weight Mode Reloads Itself

Apr 30, 2012

My access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.

View 2 Replies View Related

Cisco Wireless :: Reset 1522 Series Lightweight Access Point To Factory Default?

Jan 13, 2013

I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.

View 1 Replies View Related

Cisco :: 1200 Series Upgrade Failure?

Mar 22, 2011

I have a Cisco 1200 Series (AIR-AP1231G-A-K9) access point, I have been upgrading these models to lightweight mode but are having issues with one in particular, this access point  keeps "rebooting" itself, I am assuming that the upgrade failed, how can I  get the access point upgraded?
 
When I start to access the AP by typing "enable" and enter the password it starts resetting again.
 
I have reset the AP by the mode button, power option but still not working.
 
At this point I would even accept a fix to get it back to working condition. Here is a capture.

Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]

[Code].....

View 15 Replies View Related

Linksys Access Point :: Configuring WAP54G V3.1 Without CD?

Nov 14, 2011

how to set up a WAP54G v3.1 Access Point if you've misplaced the CD?

View 5 Replies View Related

D-Link DIR-655 :: Configuring It As Secondary Access Point?

Sep 15, 2009

I have a DLG-4500 router as my primary router and want to connect a second router (DIR-655) to it as an extention of the LAN to the second floor of my home. I have found instructions on doing this with most other routers, but not DLINK.  In fact when doing the initial configuration and trying to disable the WAN link on the second router by using a bogus IP address string (127.0.0.1) The router won't let me save the change?  What are the steps for configuring a secondary router cascaded to the primary (both wireless) to extend network coverage.

View 13 Replies View Related

Cisco :: Configuring Aironet 1100 Access Point?

Dec 22, 2011

I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?

View 8 Replies View Related

Linksys Cable / DSL :: Configuring WAG120N Like Access Point?

May 17, 2010

i have a router to connect on Internet, i need it because it let me use VOIP. I want to use WAG120N like Access Point Wireless because my VOIP router is not wireless.
 
How i have to configure it? What kind of incapsulation i have to use? VOIP router IP: 192.168.1.1
 
If is it possible (and if it is useful) i would to configure WAG120N with 2 IP, first one: 192.168.1.101 (to communicate with VOIP router and to let me go on internet) second one: 192.168.0.1 (to let me have control on it's configuration)
 
My devices will connect to 192.168.0.0 network

View 9 Replies View Related

Linksys Access Point :: Configuring WAP54G As A Router?

Mar 26, 2012

We have network that uses a Cisco router and use a WAP54G to access the network wirelessly.
 
We use static IP address so if someone wants to use the wireless an IP address has to be assigned to it and be manually configured for IP Address, Gateway, Sub Net Mask and DNS.
 
This is becoming unwieldly, but it is safe.  Is there any way to config the WAP54G as a router that would automatically assign an IP address in a range just for wireless devices.
 
Therefore the wireless devices could be set up as DHCP and we would use WPA/WPA2 encryption with a passkey, instead of just assigning static IP addresses.

View 1 Replies View Related

Linksys Access Point :: WAP2000 - Configuring 3 SSIDs

Mar 21, 2011

I have a rental property with 3 apartments that are sharing the same internet connection. The users are consistantly downloading more than their monthly allowance, and I would like to monitor how much data each apartment's users are downloading.My plan is to purchase a Cisco WAP2000 Access Point and configure 3 SSIDs (one for each apartment). I havent decided if each SSID is to be setup on it's own VLAN.
 
Will I be able to use SNMP to monitor the data that each SSID has downloaded each month? I am happy to use a network management software package (such as PRTG from Paessler) for the actual monitoring itself, but I just need to know if the SNMP in the WAP2000 Access Point will provide the information to begin with.

View 1 Replies View Related

Cisco :: Setting Up Aironet 3500 Series Access Point

Nov 21, 2012

links with information / guidelines for the initial setup for this Access Point?

View 7 Replies View Related

Belkin Routers :: Configuring An Older 5FD8230-4 As Access Point?

Dec 16, 2012

I am trying to configure an older Belkin Router (Model Number 5FD8230-4) as an Access Point so that I can boost the range of my network. The problem I have is in configuring the old router. It won't allow me to change any settings, or at least the changes don't stick, even after clicking "apply changes". I tried creating an administrative password but I am not even sure that this is working. I am using a Macbook, so perhaps this is an Apple compatibility issue. I have tried resetting the router and reverting to Factory default settings, but no joy.

View 3 Replies View Related

Cisco Switching/Routing :: Why Boot Up Takes Long Time - Aironet 1200 Series

Nov 24, 2011

I have a Cisco Aironet 1200 Series Access Point. It takes long time to boot up.
 
After showing the warning banner message it takes long time before asking for username.
 
The sh version is given below.
  
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA4, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Tue 05-Sep-06 14:15

[Code].....

View 3 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved