Linksys Access Point :: WAP2000 - Configuring 3 SSIDs
Mar 21, 2011
I have a rental property with 3 apartments that are sharing the same internet connection. The users are consistantly downloading more than their monthly allowance, and I would like to monitor how much data each apartment's users are downloading.My plan is to purchase a Cisco WAP2000 Access Point and configure 3 SSIDs (one for each apartment). I havent decided if each SSID is to be setup on it's own VLAN.
Will I be able to use SNMP to monitor the data that each SSID has downloaded each month? I am happy to use a network management software package (such as PRTG from Paessler) for the actual monitoring itself, but I just need to know if the SNMP in the WAP2000 Access Point will provide the information to begin with.
View 1 Replies
ADVERTISEMENT
Jan 20, 2011
I have an iPad 1 with newest iOS version connecting to a WAP2000 device setup with WPA2 Personal, MAC Address Connection Control enabled and SSID Broadcasting disabled, VLAN enabled (WAP2000 is running on latest firmware). Everything works well, but I keep seeing my iPad disconnecting (WIFI icon disappearing in status bar) after about 30-40 minutes of using wireless. It then takes about a minute until it connects again.
View 3 Replies
View Related
Nov 13, 2011
I have an iPad 1 with newest iOS version connecting to a WAP2000 device setup with WPA2 Personal, MAC Address Connection Control enabled and SSID Broadcasting disabled, VLAN enabled (WAP2000 is running on latest firmware). Everything works well, but I keep seeing my iPad disconnecting (WIFI icon disappearing in status bar) after about 30-40 minutes of using wireless. It then takes about a minute until it connects again.
View 1 Replies
View Related
Aug 11, 2011
I have a WRVS4400N that brocasts two different SSIDs. One is a public network and the second is a private network. Right now, both SSIDs are pulling from the same DHCP server, but I would like to seperate the public from the private. How can I seperate these SSIDs by vlans? I can't seem to get the vlans to route to sperate ports.
This is my vlan settings. I have two DHCP servers right now. One is in an isolated network plugged into Port 3 of the WRVS4400N. The other is on the production network, plugged into port 1 of the WRVS4400N. For some reason, whenever I connect to SSID Public, it won't pull an IP from the DHCP on port 1, it only pulls it from the one on port 2.I know there is three SSIDs here, the Static one is going to be the same network as the EMS one.
View 1 Replies
View Related
Nov 14, 2011
how to set up a WAP54G v3.1 Access Point if you've misplaced the CD?
View 5 Replies
View Related
May 13, 2013
I have 2 cisco 1242Ag APs in one building and 7 in other building installed in my infrastructure. All these 9 APs are connected to WLC and all of them are added to default ap group to broadcast all the ssid... But 7 in the second bulding are working properly, but the 2 in the other building are not broadcasting the ssids. I checked the configuration in both APs and WLC as well... All the 9 APs are having the same configuration.
View 12 Replies
View Related
May 17, 2010
i have a router to connect on Internet, i need it because it let me use VOIP. I want to use WAG120N like Access Point Wireless because my VOIP router is not wireless.
How i have to configure it? What kind of incapsulation i have to use? VOIP router IP: 192.168.1.1
If is it possible (and if it is useful) i would to configure WAG120N with 2 IP, first one: 192.168.1.101 (to communicate with VOIP router and to let me go on internet) second one: 192.168.0.1 (to let me have control on it's configuration)
My devices will connect to 192.168.0.0 network
View 9 Replies
View Related
Mar 26, 2012
We have network that uses a Cisco router and use a WAP54G to access the network wirelessly.
We use static IP address so if someone wants to use the wireless an IP address has to be assigned to it and be manually configured for IP Address, Gateway, Sub Net Mask and DNS.
This is becoming unwieldly, but it is safe. Is there any way to config the WAP54G as a router that would automatically assign an IP address in a range just for wireless devices.
Therefore the wireless devices could be set up as DHCP and we would use WPA/WPA2 encryption with a passkey, instead of just assigning static IP addresses.
View 1 Replies
View Related
Apr 26, 2013
Having some problems connecting up my "new" AP My current set-up consists of a Netgear "Virgin Superhub" cable modem/wireless router, a ZyXEL WRE2205 (repeater) in the hall on the first floor, and Ethernet connections through to a number of rooms, including the loft. I can't get wireless access in the loft, and I want to put the AP up there, connected through Ethernet. I want to use the same SSID and security for the AP as on the router and repeater so I can roam around(!) That's possible isn't it?What I've done so far (which hasn't worked) is connected via laptop to AP, set AP into AP mode(!), set the AP to dynamic IP, set the SSID / security the same as the router/repeater, plugged the AP into the Ethernet and tried to connect.
View 7 Replies
View Related
May 28, 2011
I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies
View Related
Jan 17, 2013
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
View 1 Replies
View Related
Sep 15, 2009
I have a DLG-4500 router as my primary router and want to connect a second router (DIR-655) to it as an extention of the LAN to the second floor of my home. I have found instructions on doing this with most other routers, but not DLINK. In fact when doing the initial configuration and trying to disable the WAN link on the second router by using a bogus IP address string (127.0.0.1) The router won't let me save the change? What are the steps for configuring a secondary router cascaded to the primary (both wireless) to extend network coverage.
View 13 Replies
View Related
Dec 22, 2011
I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?
View 8 Replies
View Related
May 29, 2012
I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan? I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan?
View 6 Replies
View Related
Dec 16, 2012
I am trying to configure an older Belkin Router (Model Number 5FD8230-4) as an Access Point so that I can boost the range of my network. The problem I have is in configuring the old router. It won't allow me to change any settings, or at least the changes don't stick, even after clicking "apply changes". I tried creating an administrative password but I am not even sure that this is working. I am using a Macbook, so perhaps this is an Apple compatibility issue. I have tried resetting the router and reverting to Factory default settings, but no joy.
View 3 Replies
View Related
Apr 19, 2012
I recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.
View 1 Replies
View Related
Dec 19, 2011
how to configure Cisco 1252-AG-A-K9 Access Point Root and Repeater?
View 9 Replies
View Related
Jan 3, 2013
I have a tplink acess point TL-wa5110G . I have WISP ( wireless internet service provider). I have configured the acess point on wisp client router mode and wan type to pppoe gave the username and pwd..Now i want to share internet wirelessly. now my question is that can i connect the aces point to wan port of the wirless router to share internet wirlessly? Because i have seen the instruction figure in tplink access router where they have shown that u can connect it with with unmanage able switch to share it to wired lan.i want to ask can wirless works to share internet if i use wireless router to access point.
View 1 Replies
View Related
Feb 27, 2012
configuring DHCP on access point, i have cisco 1142N access point, in my network.. working in autonomous mode, i have assigned a static ip to access point with default gateway.. from AP i'm able to reach internet and user connecting to access point are not able to get ip.. i have DHCP server in my network. how to make access point to fetch ip from my dhcp server and assign the saem to client.
View 10 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
Jan 3, 2011
We forgot the IP address of this WAP, and resetting the router doesn't take it to the default IP, no matter how I try to reset it. The SSID (and WEP key) stays the same too, which makes me wonder if the reset button is even working. We can still connect computers wirelessly through it and have them access the internet. Our issue is we need to change the SSID. Right now it just connects people invisibly - it gives them IPs from the subnet it's attached to, and yet the various DHCP servers I've connected to never show it as having its own DHCP address.
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related