Cisco Wireless :: Can't Access WAP2000 Web Console
Jan 3, 2011
We forgot the IP address of this WAP, and resetting the router doesn't take it to the default IP, no matter how I try to reset it. The SSID (and WEP key) stays the same too, which makes me wonder if the reset button is even working. We can still connect computers wirelessly through it and have them access the internet. Our issue is we need to change the SSID. Right now it just connects people invisibly - it gives them IPs from the subnet it's attached to, and yet the various DHCP servers I've connected to never show it as having its own DHCP address.
View 1 Replies
ADVERTISEMENT
Feb 13, 2011
I'm having an issue with our WAP2000 access point. I had to reset the access point and now I can't access the admin console. I've set a static IP address just as I did when I first set it up. Now when I browse to the 192.168.1.245 in my browser it just displays an Authentication error.
View 1 Replies
View Related
Jan 20, 2011
I have an iPad 1 with newest iOS version connecting to a WAP2000 device setup with WPA2 Personal, MAC Address Connection Control enabled and SSID Broadcasting disabled, VLAN enabled (WAP2000 is running on latest firmware). Everything works well, but I keep seeing my iPad disconnecting (WIFI icon disappearing in status bar) after about 30-40 minutes of using wireless. It then takes about a minute until it connects again.
View 3 Replies
View Related
Nov 13, 2011
I have an iPad 1 with newest iOS version connecting to a WAP2000 device setup with WPA2 Personal, MAC Address Connection Control enabled and SSID Broadcasting disabled, VLAN enabled (WAP2000 is running on latest firmware). Everything works well, but I keep seeing my iPad disconnecting (WIFI icon disappearing in status bar) after about 30-40 minutes of using wireless. It then takes about a minute until it connects again.
View 1 Replies
View Related
Mar 21, 2011
I have a rental property with 3 apartments that are sharing the same internet connection. The users are consistantly downloading more than their monthly allowance, and I would like to monitor how much data each apartment's users are downloading.My plan is to purchase a Cisco WAP2000 Access Point and configure 3 SSIDs (one for each apartment). I havent decided if each SSID is to be setup on it's own VLAN.
Will I be able to use SNMP to monitor the data that each SSID has downloaded each month? I am happy to use a network management software package (such as PRTG from Paessler) for the actual monitoring itself, but I just need to know if the SNMP in the WAP2000 Access Point will provide the information to begin with.
View 1 Replies
View Related
May 2, 2012
My Linksys Routers IP is 192.168.1.1 am unable to access the console, although i changed the computers IP 192.168.x.y. i have tried by Hard Resetting the Router but still the same?
View 1 Replies
View Related
May 7, 2013
We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies
View Related
Mar 4, 2013
I have a linksys WRT120N connected to the internet, and I want to set up my WAP2000 as a repeater. I followed all instructions, same SSID, Security, Channel, etc (y left the IP by default, though) but devices connected to the WAP2000 don´t get an IP and can´t connect to the internet. I wanted to kno if the WRT120n´s signal can be repeated, and if so if I need to change any configuration parameter.
View 2 Replies
View Related
Dec 20, 2010
I have a working WAP2000 that won't accept the 2.0.3.4 upgrade file. After selecting the file and pressing the UPDATE button, I receive the following error:
This webpage is not available.The webpage at URL might be temporarily down or it may have moved permanently to a new web address.
View 5 Replies
View Related
Mar 22, 2011
we want to use a WAP 2000 Box as repeater of an AP541n. Do naybody know this is possible or not?
Which Cisco AP boxes are compatible to act as repeater on a AP541n?
View 1 Replies
View Related
Mar 14, 2011
We have a WAP2000 that supports a few wireless users in a shop environment. Users authenticate using RADIUS. Users connect without issue and can browse the Internet.
The main local network uses a Cisco 800 router to connect to the Internet via DSL and there is an IPsec VPN tunnel to our main office.
When a user is connected to the network via a wired connection, all systems work as expected. If they are on wireless, they cannot connect to services at the main office. They must make a PPTP VPN connection for applications to function.
The WAP2000 has the latest firmware 2.0.4.0. It has a static IP on the local subnet.
View 2 Replies
View Related
Mar 14, 2013
I am doing support for a library that has 2 WAP2000 devices that have no security. These are for the patrons to connect to the internet at the library. They want to track how many people are connecting to the internet. Can I log how many computers connect to these access points or get another WAP that will track how many computers connect to the internet?
View 1 Replies
View Related
Apr 18, 2011
Cisco has recently released firmware 2.0.4.0 for the WAP2000 wireless access point. This firmware has two annoying bugs in new JavaScript code which validates SSID names on the "Basic Wireless Settings" page.
First of all, this firmware does not allow SSID names to contain spaces, even though a space is a legal character in a SSID name!
Secondly, this firmware only allow the first SSID name to be 31 characters longs, even though the maximum allowed SSID name length is 32 (and the input field even allows 32 characters to be entered in the first place!)
If either case you will get an "Illegal SSID Name!" alert message (the developer could apparently not be bothered to make the message more specific and tell the user WHY the SSID name is supposedly illegal), and you will not be able to add additional SSIDs, or configure these existing SSID's on new access points that have this firmware.
The workaround is to revert back to firmware 2.0.0.5. You can upgrade to 2.0.4.0 after adding the "illegal" SSID names, they will remain after upgrading.
The new firmware does have an interesting new feature: it can download its configuration from a TFTP server (either through DHCP or by specifying the server), but I have not been able to find the documentation on how to get this working.
View 2 Replies
View Related
Jan 12, 2011
Not long ago i was bought Cisco wap2000 access point for small business, and now the problem is to find power injector for this device. I am already tried to use AIR-PWRINJ3, but access point did't turn on.
View 7 Replies
View Related
Jul 15, 2010
Is there no way to see which clients are connected to a WAP2000 Access Point? I'm not finding the option and a little
View 2 Replies
View Related
Jan 23, 2013
Our customer setup requires an outdoor WAP (the main WAP) and two wireless signal repeters (that will be WAP2000). The repeaters will be powered over the Ethernet only and will be connected to the same switch as the main WAP (unknown vendor). My question is:
Will a WAP2000 work smoothly as a repeater when it's powered over Ethernet only and connected to the same switch as the main WAP is?
I noticed that WAP2000 connected this way was sort of 'lost' in deciding to repeat a signal or work as an independent wireless access point. The problem was immediately removed once the repeater was disconnected from the switch and powered from an outlet. I am not sure whether it was wrong addressing setup or something else that was needed to check/uncheck.
View 4 Replies
View Related
Aug 31, 2011
I have a few questions about the Cisco WAP2000 we setup for our customers that I have experienced as of late.
1. The AP is prone to reset automatically; what causes the access point to do this and how can this be prevented?
2. The AP has the SSID and the encryption reset back to factory defaults, however the IP address does not get reset. What would cause this?
3. Is it possible to use 2 of the Cisco WAP2000 as a repeater to increase signal strength of another Cisco WAP2000 that has interference from another stronger signal?
View 1 Replies
View Related
Mar 17, 2011
We have two WAP2000's in our offices which we roam between depending on which office we are in. Lets call them Access point A and Access point B.Both are firmware 2.0.4.0 and have seperate IP addresses. Both are set up with two SSID's and VLAN tagging. Both handle connections just fine and can route traffic. Both are PoE and the catalyst switch reports PoE util at 25% over all of its ports.After 10 minutes of uptime, Access point B will close all of its TCP ports - SNMP, Web admin etc but does still handle wireless connections and traffic correctly. Access point A does not close any ports.I have confirmed that when the problem happens, Access point B still handles traffic just fine by checking the MAC address the clients is associated with, as well as powering down Access point A and confirming traffic is flowing. Access point B will also respond to ICMP ping after it has closed all of its management ports. I have confirmed there is no other device on the network attempting to use the same IP address as Access point B.
I have also confirmed that I am attempting to access the management ports from the management Vlan (1) - else I would not be able to reach Access Point A's management ports either. I have turned wireless management access on for Access point B and the ports close after 10 minutes of uptime from the wireless side too, so highly unlikely this is a vlan issue.I have confirmed all of the settings (bar the IP address config) exactly match on both Access point A and Access point B. The firmware revisions are the same.
View 2 Replies
View Related
Aug 22, 2010
I have several WAP2000 (Firmware 2.0.0.5), and while they work fine for PC's, iPhones, iPod touches cannot connect to them.Well, they connect briefly, get an IP address from the router, and immediately drop the connection to re-connect again.I have tried changing channels, eliminating all but one of the AP's, and so forth. Any issues with this firmware? I see posts where people are saying their iPhones connect up fine. This happens on versions 3.x and 4.x of the iphone O.S. It's not limited to one iphone or ipod touch; we've tried several.
View 12 Replies
View Related
May 2, 2012
I have linksys ADSL Router which is having one line port for Phone Line and 4 Ethernet Ports.The Router IP is 192.168.1.1. When i connect this Router through one of its Ethernet Port to one of the Network Point(which is DHCP enabled)is working fine. I get the IP 192.168.3.x from my existing DHCP not from the ADSL Router which is enabled.Secondly, Although i can Ping the Router IP 192.168.1.1 from Wifi client 192.168.3.X, But when i try to open the Router Console a Login window open and is says " your are trying to access the Router in an insecure ways and it doesnt not authenticate ID and PWD.When i directly connect Router to my Laptop then am able to do so.
View 1 Replies
View Related
Apr 19, 2013
I have a problem with my vpn concentrator. I cannot access it through console, I have tried every baud rate that is available on my SecureCrt but it won't display anything. At first, I thought that my console cable is defective but I was able to access a WLC via console cable together with the rj45 to db9 converter. I also tried connecting the vpn concentrator to a switch and enable the cdp in the switch but the "show cdp neighbor" can't detect or display the vpn concentrator even if the interface status is "up up". Is it safe to say that the VPN concentrator is already broken?
View 1 Replies
View Related
Sep 4, 2012
but is there anyway to access directly a LAP 1522 using a console port?
View 5 Replies
View Related
Apr 9, 2013
I can access the web console, and also have telnet access but only to a VT100 menu system - How do I access the full console command prompt (without using the serial console connection)?
View 4 Replies
View Related
Jan 4, 2013
I can not access the switch through the console. The web interface is working properly.
Model: SRW224g4
Below some pictures. The Hyper Terminal settings. Error:
View 6 Replies
View Related
Jan 18, 2013
Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
View 3 Replies
View Related
Jun 14, 2011
we have two pix535 one is ur other is FO license.
once a time i found can't access FO pix535 console, i'm sure console cable is ok. when i unplug failover serial cable from FO pix535, i can access pix 535 console.
View 3 Replies
View Related
Feb 9, 2012
I have an asa 5585x cluster. I get ssh access but no console access on the standby unit.
On the active unit, when I try console access, ASA ask for a password. I have tried all the one that I have configured, but without success.
View 5 Replies
View Related
Aug 15, 2011
I am having FWSM in active /standby mode deployed on two different cat 6k chassis. Unable to access the fwsm module from switch using ' session module mod_no processor 1 ", it throws error " % telnet connections not permitted from this terminal" Running Version 3.2.6 on fwsm, Cat 6k is running 12.2.33.SXH1,
switch#session slot 3 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
% telnet connections not permitted from this terminal
---------------------------------------------------------------------------
have allowed telnet on line vty, configuration on Line vty is simple allowing all transport protocols
line vty 0 4
exec-timeout 5 0
transport input all
transport output all
line vty 5 15
exec-timeout 5 0
transport input all
transport output all
View 3 Replies
View Related
Feb 29, 2012
today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies
View Related
Dec 27, 2012
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies
View Related
Jun 30, 2012
I just purchased a used Catalyst 2900 XL switch and have not been succesful in connecting to the console via minicom 2.5 running on Ubuntu 12.04 or 11.10, I don’t even get junk charecters in the terminal or echo on input. The switch passes POST according to the LEDs on the front and the network ports are fucntional for switching purpouses.
I’m using a Prolific PL2303 USB-Serial adapter, which works with minicom to console into another device. I’ve tried every baud rate available and tried combonations of hardware flow control, software flow control, and niether.I’ve tested the pinout of the console cable and all pins map correctly according to Cisco spec.I’ve also tried Cutecom, putty, and screen. I have not tried HyperTerminal because I do not use windows.Is it possible that the previous owner disabled console access? Do I need to reboot the switch each time I test a different baud rate?
View 4 Replies
View Related
Jan 11, 2012
I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies
View Related
Apr 3, 2011
My Wifi internet was working fine 12 hrs ago; now I can only use it with wire.I uninstall 2.0 and install Asus wireless console 3.0 but still not working, Fn+F2 not working either.
[code]...
View 2 Replies
View Related
