I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 RepliesI have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
I have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies View RelatedI want to configure my switch via console cable, the switch boots up normally, and there are no configurations present on the switch. However, anything I type does not appear on the terminal client. I used several terminal clients (TeraTerm, PuTTY, HyperTerminal), all latest versions as well as different PCs. I even forced the switch to rommon mode, still, anything I type does not appear on the terminal client.
Here's the output of TeraTerm:
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: e8:40:40:06:f0:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
[code]....
After the last line, I can not type any command at all. I encountered this on three 2960 switches that we have here in our laboratory.
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
I planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies View RelatedI am having 2960 switch and one port is configured with a VLAN and connected with an unmanageable switch and further one more unmanageable switch was connected to the primary unmanageable switch…
The topology will be 2960 switch -> unmanageable Switch -> unmanageable -> PC connected
The issue I am facing most of the PC are getting IP addresses through DHCP server and very few 5 or 6 PC’s out are not getting the IP from DHCP server.If I switch of the switch and switch on the issue is resolved for those and it will raise for some other PC’s.
i have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
View 14 Replies View RelatedI am unable to connect a Wifi Modem wiith 2960 Switch having VLAN 1,Attached is the network diagram,what configurations i have to modified it,I need to Connect A Wifi Modem on VLAN 1 ,Connectivity is working fine between VLAN 10 and VLAN 1.What should be the next step to Connect Wifi Modem to VLAN 1 so that Users on VLAN 10 should connect to Internet.
View 14 Replies View RelatedI am having FWSM in active /standby mode deployed on two different cat 6k chassis. Unable to access the fwsm module from switch using ' session module mod_no processor 1 ", it throws error " % telnet connections not permitted from this terminal" Running Version 3.2.6 on fwsm, Cat 6k is running 12.2.33.SXH1,
switch#session slot 3 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
% telnet connections not permitted from this terminal
---------------------------------------------------------------------------
have allowed telnet on line vty, configuration on Line vty is simple allowing all transport protocols
line vty 0 4
exec-timeout 5 0
transport input all
transport output all
line vty 5 15
exec-timeout 5 0
transport input all
transport output all
I had a strange issue yesterday when onsite installing a new access switch.Port capacity full on a two switch stack of 3750 x48 PS switches (WS-C3750- 48PS-E)- New 2960 x48 PS - WS-C2960S-48FPS-L racked, with the plan of using it just as an edge switch via SFP Stacking cable.Setup the two connecting ports with simple initial config: - switchport mode trunk- no encapsulation option on the 2960, default dot1q- dot1q set on 3750 port- no shut on both sides.Connected the SFP Stacking cable but it didnt work:- %PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi1/0/1 is not supported
This is ok as I had a backup:- Next step tried using 2 x Short Haul SFP SX GBIC's with LC - LC OFNP 50/125 fibre patch lead - no joy- Extra backup of 2 x Long Haul SFP LX GBIC's with the same fibre patch - no joy- Checked the fibre and it was not a cross over so transmit and receive going down the same side, switchedand still would not come up.- Used Fibre as a straight through and still the same.In all cases there was no indication of any life in the connection.It is pointing to a faulty fibre patch lead but I know it has worked in the past. Could it be something to do with the config or device incompatibility? Or any setting I need to activate?
I have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies View RelatedI can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
Unable to access switch from outside the local network. Can get to all routers and PC's
View 2 Replies View RelatedMy requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
I am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies View RelatedI have 2 Catalyst 2924 switch in a home lab. Both of them have developed the same problem at the same time (strange). I have tried all that I can think of. I can telnet to them but cannot access via the console port. On a telnet session I execueted a "write erase, reload" on one of them. As I anticipated this threw me out of the telnet session and I presently have no access to that switch.
The console cable is fine, works for all other devices.
I've been assinged a task to connect our branch office with the head office, so that the IP Phones in the branch office can be connected to Cisco Call Manager at head office. To accomplish this they have given a Cisco 877 Adsl router a 10 Port 3-COM POE Switch and 3 Cisco 7911 IP Phones. Currently the there are 7 PC's Connected to 3 COM Switch which indeed is connected to a Internet router(Speedtouch). First I thought of connectiong the IP Phones to the Ethernet Port on Cisco 877 router but had to change my mind as the ports are non POE ports and I do not have adapters for IP phones. So I've decided to connect the Phones to 3 COM Switch and create VLAN's (DATA & VOICE) and pass the DATA traffic through Speed Touch and Voice traffic through the Cisco 877 router, but when I tried accessing the 3-COM Switch via Console I am getting Junk language( See the attachment for reference).
how can I pass through this Junk messeges and access the switch
[Code].....
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
i'm trying to enable command authorization for ssh as well as console access to a Nexus 7010 box (version 5.0). Following is the config:
aaa group server tacacs+ ACS5-1
server 10.12.19.11
server 10.12.19.12
source-interface loopback0
snmp-server enable traps aaa server-state-change
aaa authentication login default group ACS5-1 local
[code]....
As you can see, the default group configuration ACS5-1 for authenticatoin has applied to both defaults and console. But the command authorization does not appear to be applied to the console. As a result, when i login from the console and get authenticated, the command authorization does not trigger and i can run commands I'm not supposed to. In the configuration, I do not see "aaa authorization console" option unlike we have in IOS.
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies View RelatedI have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 Replies View Relatedtoday I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies View RelatedI just purchased a used Catalyst 2900 XL switch and have not been succesful in connecting to the console via minicom 2.5 running on Ubuntu 12.04 or 11.10, I don’t even get junk charecters in the terminal or echo on input. The switch passes POST according to the LEDs on the front and the network ports are fucntional for switching purpouses.
I’m using a Prolific PL2303 USB-Serial adapter, which works with minicom to console into another device. I’ve tried every baud rate available and tried combonations of hardware flow control, software flow control, and niether.I’ve tested the pinout of the console cable and all pins map correctly according to Cisco spec.I’ve also tried Cutecom, putty, and screen. I have not tried HyperTerminal because I do not use windows.Is it possible that the previous owner disabled console access? Do I need to reboot the switch each time I test a different baud rate?
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedI'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies View RelatedI am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies View Related