Cisco Switching/Routing :: 2924 Switch - No Response From Console Port?
Dec 11, 2011
I have 2 Catalyst 2924 switch in a home lab. Both of them have developed the same problem at the same time (strange). I have tried all that I can think of. I can telnet to them but cannot access via the console port. On a telnet session I execueted a "write erase, reload" on one of them. As I anticipated this threw me out of the telnet session and I presently have no access to that switch.
The console cable is fine, works for all other devices.
View 15 Replies
ADVERTISEMENT
May 3, 2013
I attached the terminal to the console port to watch the bootup sequense, but nothing appear the same cable used on athor switches and router without any issue.procedure to access the router noting that Giga ports not working also.
View 2 Replies
View Related
Feb 26, 2012
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies
View Related
Apr 6, 2012
I have a brand new 2911 router out of the box. I attached a terminal to the console port and watched the bootup sequence. I get the "press return to get started" at the end but I can't get any response. I just used the same cable and terminal on a 3750 switch and an ASA. What am I missing?
View 3 Replies
View Related
Apr 10, 2012
We got a switch issue here for 4507R-E with two sup6l-e supervisor running sso redudant. and we found that sometimes client can't ping through the local vlan ip add on the switch , can't logon the cli by telnet too. In the direct connected network device such as access switch and ASA , can't ping or telnet the 4507R too. when we made a forceswitch to sso standby supervisor from console , the problem solve and everything get fine . after that, we switch angin back to the origin supervisor , fine too.
before we made the supervisor forceswitch , we had check the system cpu usage is 15 - 20 % from console . also we had creat a new vlan 200, attach the notebook to 4507's vlan 200 port , the notebook can't ping or telnet the vlan 200 ip interface too.
View 1 Replies
View Related
Nov 13, 2011
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
View 11 Replies
View Related
Mar 18, 2013
I can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
View 3 Replies
View Related
Nov 3, 2011
My requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
View 3 Replies
View Related
Dec 27, 2012
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies
View Related
Feb 7, 2013
I am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies
View Related
Feb 20, 2013
I want to configure my switch via console cable, the switch boots up normally, and there are no configurations present on the switch. However, anything I type does not appear on the terminal client. I used several terminal clients (TeraTerm, PuTTY, HyperTerminal), all latest versions as well as different PCs. I even forced the switch to rommon mode, still, anything I type does not appear on the terminal client.
Here's the output of TeraTerm:
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: e8:40:40:06:f0:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
[code]....
After the last line, I can not type any command at all. I encountered this on three 2960 switches that we have here in our laboratory.
View 6 Replies
View Related
May 12, 2012
I've been assinged a task to connect our branch office with the head office, so that the IP Phones in the branch office can be connected to Cisco Call Manager at head office. To accomplish this they have given a Cisco 877 Adsl router a 10 Port 3-COM POE Switch and 3 Cisco 7911 IP Phones. Currently the there are 7 PC's Connected to 3 COM Switch which indeed is connected to a Internet router(Speedtouch). First I thought of connectiong the IP Phones to the Ethernet Port on Cisco 877 router but had to change my mind as the ports are non POE ports and I do not have adapters for IP phones. So I've decided to connect the Phones to 3 COM Switch and create VLAN's (DATA & VOICE) and pass the DATA traffic through Speed Touch and Voice traffic through the Cisco 877 router, but when I tried accessing the 3-COM Switch via Console I am getting Junk language( See the attachment for reference).
how can I pass through this Junk messeges and access the switch
[Code].....
View 3 Replies
View Related
Feb 13, 2013
I have issue with Cisco Router 2801's Console Port. My student was doing a lab and he said during configuration, Console Port stopped responding. He was in middle of configuration, so now at present, only telnet is able to login on "R2>" user mode, enable password is not set, so getting "R2>en % No password set R2>" I have tried different terminal software but no output from Console Port, changed the Console Cables, replace with working console cables, change speed (baud) settings. Also tried to connect same console with "AUX" port and got same error mentioned above. AUX Port responds but I am not able to change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically damaged.
View 4 Replies
View Related
Nov 29, 2011
i'm trying to enable command authorization for ssh as well as console access to a Nexus 7010 box (version 5.0). Following is the config:
aaa group server tacacs+ ACS5-1
server 10.12.19.11
server 10.12.19.12
source-interface loopback0
snmp-server enable traps aaa server-state-change
aaa authentication login default group ACS5-1 local
[code]....
As you can see, the default group configuration ACS5-1 for authenticatoin has applied to both defaults and console. But the command authorization does not appear to be applied to the console. As a result, when i login from the console and get authenticated, the command authorization does not trigger and i can run commands I'm not supposed to. In the configuration, I do not see "aaa authorization console" option unlike we have in IOS.
View 2 Replies
View Related
Dec 12, 2012
I planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
View 3 Replies
View Related
Nov 11, 2012
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies
View Related
Dec 29, 2011
I console into switch 1 (or router, it doesn't matter) and everything is fine. From that session I SSH to switch 2 (or router). The session on the second device has a noticable delay when I type.Next I SSH to switch 1, then SSH to switch 2 from that session. Everything works fine.Finally, I console to switch 1, and telnet to switch 2. There is no delay.So it appears the delay only occurs when I open an SSH session while consoled into a device. It didn't matter what switch 1 and switch 2 were - I had 3560Gs, 4900Ms and a 3845 router. There's no special configuration on the console or vty ports - when I do a "show line console" and "show line vty 0" the output is basically the same.
View 2 Replies
View Related
Mar 12, 2012
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
View 5 Replies
View Related
Jan 19, 2012
What key sequence to go into ROMMON mode from the console port for VSS system with 2 VS-S720-10G?
View 3 Replies
View Related
Jul 27, 2011
I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 Replies
View Related
Jan 11, 2012
I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies
View Related
Oct 28, 2012
I have one Catalyst 6509E chassis and two SUP720. The bootup sequence on SUP 720 (standby hot) failed . Messages that appear on SUP 720, on the console port indicate o software crash. I don't have a flash card in SUP720.
This is the bootup process:
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
[code].....
View 1 Replies
View Related
Aug 29, 2011
I am having intermittent problems with wireless connectivity to this router. It stops responding to requests completely but existing connections continue to function.
The hardwired connections also are functional but I cannot get to the admin console to see what is going on. The router is currently not being used to connect to the outside world. When it was before this situation still existed. I am using firmware version V2.0.1.3
View 1 Replies
View Related
Jun 2, 2013
I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
View 3 Replies
View Related
May 8, 2012
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
View 3 Replies
View Related
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Nov 28, 2012
I am trying to track down an application response problem on my network (the traffic goes through a 6509 and FWSM).I noticed in one of my WireShark captures, that the client at times seems to be sending ackowledgements (ACKs) over and over again, and I'm not sure if this indicates a problem/ retransmission.
Basically, a web server is delivering images to the client, but end users are complaining of slowness and freezes.Wire-Shark has not flagged this as a problem (comes up "green")
View 2 Replies
View Related
Jul 16, 2012
Is it possible to use the inbuilt 4 port switch on a Cisco 887VA ADSL router for inter Vlan routing? My plan is to configure port FA0 - 2 as Vlan 1 (default) 192.168.0.254/24 and port FA3 as Vlan 2 192.168.4.254/30. My SIP server will sit on Vlan 2 192.168.4.253/30 however remote Wan users coming through other Cisco 888 routers connected to the 887 will need to access Vlan 2 from Vlan 1, is this possible?
View 12 Replies
View Related
Apr 15, 2012
There 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version 12.2(58)SE1.
View 1 Replies
View Related
Nov 25, 2012
I have a C6509 with WS-X6548-GE-TX port module. The first port group, 1-8, is showing oversubscription (packets dropping) in the shared buffer. What interface commands can I use to find the specific port causing the buffer overflow?None of the ports is continuously overutilized and none of them in a SPAN destination group.I don't want to move connections without knowing which one is causing the problem. Also I fear that moving the connections may shift the bleeding to another shared port group.
View 2 Replies
View Related
Mar 2, 2012
If I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies
View Related
Sep 8, 2010
configure port security Cisco 500 Swich ? There is no CLI mode in this switch?
View 2 Replies
View Related
