My requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies View RelatedI was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View RelatedI have a customers Catalsyt 2950 switch come in for the configuration to be cleaned to factoy default, using the link below removed the customers banner and login information whitch worked
[URL]
When i restart the switch and enter Enable mode I'm prompted with the password which i used when following the link above,
I want to remove all passwords so when the switch is redeployed to the next site who ever the engineer is that is going to be reconfiguring the switch is able to access privlage mode with out the password promt.
I am not able to successfully accomplish the password reset function. This 2950 does not respond to the mode button held down at power up or to sending a briak. I have tried both several times and the switch continues to fully boot. [URL]
C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)Compiled Mon 22-Jul-02 17:18 by antoninoWS-C2950G-48-EI starting...Base ethernet MAC Address: 00:0b:fd:a1:4f:80Xmodem file system is available.Initializing
[Code].....
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies View RelatedAfter setting up the domain name I try to use the crypto key and it is no where to be located. Below is some of the information I copied from TeraTerm
Switch-1(config)#ip domain-name justin.lab.comSwitch-1(config)#crySwitch-1(config)#cry?% Unrecognized commandSwitch-1(config)#crypto key ?% Unrecognized commandSwitch-1(config)#crypto key ^% Invalid input detected at '^' marker.
Switch-1(config)#?Configure commands: aaa
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
I can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
I have cisco 2950 catalyst switch, verson IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(20)EA1a, RELEASE SOFTWARE (fc1)
So. for one of my port (FE 0/3) i need to put the bandwith limit 512 kbps, how to configure the above same.
Note:- I configured the below but no effect
1. interface FastEthernet0/3description * CONT TO B-CENTER *switchport access vlan 10switchport mode accessbandwidth 1024speed 10
2. and there is no srr bandwidth limit option for 2950, but the same is working for 2960.
Do they have a default IP assigned to them?
I'm trying to access the CMS administration page from my browser. I've already tried 192.168.0.1 and that brings up my gateway (cable modem from Time Warner).
I upgraded a Catalyst 2950 switch and there wasn't enough room so I deleted the flash. The upgraded went well using tftp. It booted up fine. The I0S version includes crypto. But, I can't access switch via web browser or CNA. Port scan shows port 80 0pen. What am I missing?
Here is the flash.
Directory of flash:/
2 -rwx 112 Mar 01 1993 01:00:48 +00:00 info 3 -rwx 3722814 Mar 01 1993 01:02:58 +00:00 c2950-i6k2l2q4-mz.121-22.EA14.bin 4 drwx 4416 Mar 01 1993 01:03:45 +00:00 html 331 -rwx 112 Mar 01 1993 01:04:19 +00:00 info.ver 332 -rwx [code]....
I am planning to change the management IP (VLAN 5) to one of my Cisco 2950 switch, Here I am creating a new VLAN101 and assign new IP
When I am doing this VLAN 2 is going admin down.
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies View RelatedI am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies View RelatedI have 2 Catalyst 2924 switch in a home lab. Both of them have developed the same problem at the same time (strange). I have tried all that I can think of. I can telnet to them but cannot access via the console port. On a telnet session I execueted a "write erase, reload" on one of them. As I anticipated this threw me out of the telnet session and I presently have no access to that switch.
The console cable is fine, works for all other devices.
I want to configure my switch via console cable, the switch boots up normally, and there are no configurations present on the switch. However, anything I type does not appear on the terminal client. I used several terminal clients (TeraTerm, PuTTY, HyperTerminal), all latest versions as well as different PCs. I even forced the switch to rommon mode, still, anything I type does not appear on the terminal client.
Here's the output of TeraTerm:
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: e8:40:40:06:f0:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
[code]....
After the last line, I can not type any command at all. I encountered this on three 2960 switches that we have here in our laboratory.
I've been assinged a task to connect our branch office with the head office, so that the IP Phones in the branch office can be connected to Cisco Call Manager at head office. To accomplish this they have given a Cisco 877 Adsl router a 10 Port 3-COM POE Switch and 3 Cisco 7911 IP Phones. Currently the there are 7 PC's Connected to 3 COM Switch which indeed is connected to a Internet router(Speedtouch). First I thought of connectiong the IP Phones to the Ethernet Port on Cisco 877 router but had to change my mind as the ports are non POE ports and I do not have adapters for IP phones. So I've decided to connect the Phones to 3 COM Switch and create VLAN's (DATA & VOICE) and pass the DATA traffic through Speed Touch and Voice traffic through the Cisco 877 router, but when I tried accessing the 3-COM Switch via Console I am getting Junk language( See the attachment for reference).
how can I pass through this Junk messeges and access the switch
[Code].....
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies View Relatedi'm trying to enable command authorization for ssh as well as console access to a Nexus 7010 box (version 5.0). Following is the config:
aaa group server tacacs+ ACS5-1
server 10.12.19.11
server 10.12.19.12
source-interface loopback0
snmp-server enable traps aaa server-state-change
aaa authentication login default group ACS5-1 local
[code]....
As you can see, the default group configuration ACS5-1 for authenticatoin has applied to both defaults and console. But the command authorization does not appear to be applied to the console. As a result, when i login from the console and get authenticated, the command authorization does not trigger and i can run commands I'm not supposed to. In the configuration, I do not see "aaa authorization console" option unlike we have in IOS.
I planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies View RelatedI have a cisco 2950 switch, connected with 4Mbps of internet and number of users will access the internet. There is no restraction on bandwidth limit for users, if any body use high download the remaining users are facing the slow browsing problems.
So, if i can put a bandwidth limitation for every users the problem will be solved. how to restract the bandwidth on user bases.
I am trying to configure 802.1x RADIUS Authentication on cisco 2950-24TT-L Switch. I am using following set of command as given below
Switch# configure t
Switch(config)# aaa new-model
Switch(config)# aaa authentication dotx default group redius
Switch(config)# dot1x system-auth-control
Switch(config)# inter fasteth 0/1
Switch(config)#dot1x port-control atuo
I am facing problem dot1x command is not working on interface.
I would like to know if ip helper-address feature is working on a layer 2 switch (2950,2960) or you should use a Layer 3 switch to do that?
View 7 Replies View RelatedWith out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies View RelatedI have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
As always, the Cisco LMS is keep sending the follwoing high discard error from the Cisco switches WS-C2950T-24:
EVENT ID = 0004SX3
ALERT ID = 00019LF
TIME = Tue 14-Feb-2012 08:56:35 GMT
[Code].....
In my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 Replies View Relatedwe are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
Can a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies View Relatedcan i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies View Related