Cisco Switching/Routing :: 2950 - Can't Access Switch Via Browser Or CNA
Jan 5, 2012
I upgraded a Catalyst 2950 switch and there wasn't enough room so I deleted the flash. The upgraded went well using tftp. It booted up fine. The I0S version includes crypto. But, I can't access switch via web browser or CNA. Port scan shows port 80 0pen. What am I missing?
Here is the flash.
Directory of flash:/
2 -rwx 112 Mar 01 1993 01:00:48 +00:00 info 3 -rwx 3722814 Mar 01 1993 01:02:58 +00:00 c2950-i6k2l2q4-mz.121-22.EA14.bin 4 drwx 4416 Mar 01 1993 01:03:45 +00:00 html 331 -rwx 112 Mar 01 1993 01:04:19 +00:00 info.ver 332 -rwx [code]....
View 5 Replies
ADVERTISEMENT
Jul 4, 2012
I am unable to access a series of switches connected together through a management vlan. I receive the message "The server xx.xx.xx.xx at level_15_access requires a username and password." Entering the username and password fails and the same username and password message returns. I am able to ssh into the switch with the username and password that fails trying to access the switch with the browser.
How can I check the username and password for access with the browser?
I am trying to monitor switch performance. Is there a good way to monitor switch performance with the command line interface?
View 2 Replies
View Related
Jun 22, 2012
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies
View Related
Feb 8, 2013
After setting up the domain name I try to use the crypto key and it is no where to be located. Below is some of the information I copied from TeraTerm
Switch-1(config)#ip domain-name justin.lab.comSwitch-1(config)#crySwitch-1(config)#cry?% Unrecognized commandSwitch-1(config)#crypto key ?% Unrecognized commandSwitch-1(config)#crypto key ^% Invalid input detected at '^' marker.
Switch-1(config)#?Configure commands: aaa
View 6 Replies
View Related
Mar 25, 2012
I have cisco 2950 catalyst switch, verson IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(20)EA1a, RELEASE SOFTWARE (fc1)
So. for one of my port (FE 0/3) i need to put the bandwith limit 512 kbps, how to configure the above same.
Note:- I configured the below but no effect
1. interface FastEthernet0/3description * CONT TO B-CENTER *switchport access vlan 10switchport mode accessbandwidth 1024speed 10
2. and there is no srr bandwidth limit option for 2950, but the same is working for 2960.
View 3 Replies
View Related
Aug 13, 2012
Do they have a default IP assigned to them?
I'm trying to access the CMS administration page from my browser. I've already tried 192.168.0.1 and that brings up my gateway (cable modem from Time Warner).
View 15 Replies
View Related
Nov 4, 2012
I am planning to change the management IP (VLAN 5) to one of my Cisco 2950 switch, Here I am creating a new VLAN101 and assign new IP
When I am doing this VLAN 2 is going admin down.
View 3 Replies
View Related
Nov 3, 2011
My requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
View 3 Replies
View Related
Jul 17, 2012
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies
View Related
Feb 12, 2012
I have a cisco 2950 switch, connected with 4Mbps of internet and number of users will access the internet. There is no restraction on bandwidth limit for users, if any body use high download the remaining users are facing the slow browsing problems.
So, if i can put a bandwidth limitation for every users the problem will be solved. how to restract the bandwidth on user bases.
View 4 Replies
View Related
May 3, 2013
I am trying to configure 802.1x RADIUS Authentication on cisco 2950-24TT-L Switch. I am using following set of command as given below
Switch# configure t
Switch(config)# aaa new-model
Switch(config)# aaa authentication dotx default group redius
Switch(config)# dot1x system-auth-control
Switch(config)# inter fasteth 0/1
Switch(config)#dot1x port-control atuo
I am facing problem dot1x command is not working on interface.
View 1 Replies
View Related
Jan 9, 2012
I would like to know if ip helper-address feature is working on a layer 2 switch (2950,2960) or you should use a Layer 3 switch to do that?
View 7 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
Apr 15, 2010
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
View 16 Replies
View Related
Feb 13, 2012
As always, the Cisco LMS is keep sending the follwoing high discard error from the Cisco switches WS-C2950T-24:
EVENT ID = 0004SX3
ALERT ID = 00019LF
TIME = Tue 14-Feb-2012 08:56:35 GMT
[Code].....
View 4 Replies
View Related
Nov 3, 2011
In my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
View 2 Replies
View Related
May 26, 2013
how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies
View Related
Nov 4, 2012
we are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
View 1 Replies
View Related
Mar 18, 2009
Can a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies
View Related
Feb 14, 2013
can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies
View Related
Jan 27, 2013
I have a lab setup to take my CCNA and CCNP and I'm having issues trying to get WAN connectivity back to a switch at the end of my network. My lab environment consists of 1 - 2950 switch, 1 - 2620 and 1 - 2621XM. I have 1 Ethernet connection from each router to the switch and 1 serial connection from the 2620 to the 2621XM. I have the serial interfaces in a shutdown state right now so there is no loop since I do not have Spanning tree setup on the ports on the switch yet.
Right now using the fast ethernet ports on the routers and I have no issues its when I shut down those Ethernet ports and try using the serial interfaces when I start having issues. So my network layout is Ethernet from switch port f0/4 to port f0/0 on 2620 and serial from s0/1 on the 2620 to s0/2 on the 2621XM. My 2621XM f0/1 is whats connected to the WAN and I have no issues getting to the WAN from my 2621Xm or my 2620 but when I try pinging any website or even my WAN default gateway from my switch I get nothing!
Ive also noticed that when I do a IP NAT translation (after accessing the WAN from my 2620) on my 2621XM the source IP is of my serial connection not the ip of my 2620 router? I have my default gateway on the 2620 as the the IP of my serial interface on the 2621XM and vice versa because my LAN network is 172.16.1.0 and my WAN is 172.16.9.0. I have a /31 setup between my serial connections 172.16.11.0 (s0/1) is on the 2620 and 172.16.11.1(s0/2) is on the 2621XM. I used the SDM (ver 2.5) to setup NAT to have f0/1 with Nat outside and s0/2 as Nat inside. Encapsulation is HDLC between the serial links. Ive attached the running configs of the switch and routers.
View 2 Replies
View Related
Dec 11, 2011
We have a group of computers on their own VLAN. A router allows internet access while keeping them sandboxed. We don't want them accidentally connect to our production network. We blocked their wireless MACs in unauthorized WAPs. I'd like to do the same thing for their ethernet MACs on our switches, (a mixture of 2950,2960 and 2960G currently testing on C2960-LANBASE-M, Version 12.2(25)SEE2). I've been unable to locate the correct method on google, by searching these boards or in the command reference.
What is the best practice for blocking a group of MACs from accessing a particular VLAN on a network consisting of several Layer 2 Switches?
View 4 Replies
View Related
Apr 5, 2013
i am trying to set up a cisco 2950 with a vlan to seperate all of the pos machines on the network (4 of them) from all other machnes in the building (3 hard wired and wi-fi). i was going to use vlan 1 as a trunk to allow internet access to go from fa0/1 to both vlans (vlan 10 and vlan 20). i have read things about the acl having an explicit deny at the end, so i'm thinking that is my problem. i am testing it at my house before deploying it to the network. i have 1 laptop setup with an ip of 192.168.0.50, and the other is .60. my router is 192.168.0.1. i have the ethernet from the router plugged into fa0/1, the 1st laptop on fa0/2 and the other at fa0/3. before i set the vlans up, i checked the communication by just plugging them in and trying to ping, they could both ping each other, the router and 8.8.8.8. when i finished setting up the test vlans, they could not ping each other(what i wanted) and laptop 1 can ping the router, and 8.8.8.8. laptop 2 cannot ping anything.
the only thing i did was create vlan 10 and 20, set port fa0/2 to vlan 10 and no sh, fa03 to vlan 20 and no sh, fa0/1 to vlan 1 and no sh. then i did switchport mode trunk on fa0/1, and switchport native vlan 1. this seems to be how i was supposed to do it, but it's been a while since i have worked with switches. i'm sure it's simple, but after searching the internet and poring over my cisco books for 5 hours, it is turning out not to be the case. here are some details:
greenhouse#sh int fa0/1 switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
[code]...
View 10 Replies
View Related
Dec 18, 2012
i bought a cisco 2950 series switch to play around with and im trying to set it up to SSH. I have google'd a bit on how to do this and i've sort of hit a wall... i have downloaded the cryptographic image from cisco's website, installed a TFTP server (think this is where my issue lies) but when i do the copy tftp flash global command i keep getting the error accessing "xxxx" message.I have tried allowing the server through windows firewall, disabling windows firewall, allowing access through the router..
View 6 Replies
View Related
Mar 4, 2012
On firewall we have zone created for dmz and ip is 192.x.x.x and it is connected to 2950 switch(DMZ switch) with vlan 25..We have L3 switch on this we have created vlan 25 and connected cable from L3 with 2950 switch with vlan 25
As we have the servers on L3 and wanted to bring on dmz zone we have connected a cable.Now the problem is when i connect a pc on 2950 switch (directly on dmz switch) with access-list below we are not geeting any hist on it.
View 6 Replies
View Related
Jan 16, 2011
is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies
View Related
Feb 11, 2012
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies
View Related
Apr 25, 2013
I have a server windows 2008 that I would like to have a nic teaming configuration, the server has two nics, each nic is connected to a different switch. One is connected to cisco 2960 and the other is connected to cisco 2950. I have read here in forums about nic teaming but using the same switch. I have not found using different switch. Is this possible?
View 1 Replies
View Related
Jan 11, 2012
2950 switch has a IOS on flash , but i would like to set the swith like...
1. switch IOS to be loaded from TFTP server .if it fails
2. Loaded from local flash IOS1 , if it fails
3. IOS loaded from local flash IOS2.
does 2950 switch support this feature.
View 2 Replies
View Related
Jun 11, 2012
I have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies
View Related
Dec 14, 2011
I have a cisco catalyst 2950 switch (flash:c2950-i6q4l2-mz.121-22.EA1b.bin), in remote location with public IP,how to upgrade ios remotely, by that time running configuration will go?how much down time is required and ?
View 7 Replies
View Related
Jun 12, 2012
I have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
router
|
2950 - vlan 1,2,3,4,5,6,7,8,9,10
[Code].....
View 12 Replies
View Related
Dec 9, 2011
c2950-i6q4l2-mz.121-22.EA10a.bin is the image name of the 2950 switch i have in my office. what is the meaning of " i6q4l2 "? I saw some IOS like IP base, adv-security. but i didn't see anything like this before.
View 2 Replies
View Related
