I have a cisco 2950 switch, connected with 4Mbps of internet and number of users will access the internet. There is no restraction on bandwidth limit for users, if any body use high download the remaining users are facing the slow browsing problems.
So, if i can put a bandwidth limitation for every users the problem will be solved. how to restract the bandwidth on user bases.
I want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
I want to limit the bandwidth of my Catalyst 3750 series switch, I read the cisco documentation and I applied the commands but I didn't get the wanted results.
For the outbound traffic it's ok, but for the inbound traffic I used policing but I get an unstable traffic. I used, an access list and a class-map to classify the traffic and then a policy-map.(I followed the steps mentioned in this site: [URL]
configuring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
I have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
I have the requirement to assign an asymmetric bandwith limit to each port on a switch (example: 4Mbps downlink, 1Mbps uplink). I've been searching and found the option to apply policers or srr-queue mechanism to achive this, however this only applies for one direction only as far as I know. Catalyst 2960 familiy is preferred, however if this is not possible, will possibly jump to the 3560X family.
We run a workers camp here and we currently have around 2500-3000 people using our 100MB internet pipe. We are upgrading the pipe to 200MB soon but I still would like to limit how much bandwidth everyone is using.
We allow streaming media such as Netflix, youtube, apple TV and of course .So it gets full pretty fast. We have QOS implemented although I wasn't here when it was done so I don't know a lot about it. I would like to limit IPs to a certain amount of bandwidth. [code]
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
I have a cisco 2821 router where as a cisco 2960 switch with connect on router as a trunk & one user vlan . this is my WAN router all traffic are internal . i have 2MB data connectivity on my WAN side. i have to Give a specific Bandwith on my SAP traffice . like when SAP traffice will come they all time get around 50 % bandwidth of my channel. If SAP resuest are not comming then other traffice will get full bandwith .
I use WS-C3560G-24TS and try both ios 12.2.50.SE1 and 12.2.46.SE but problem the same. The config as following, interface GigabitEthernet0/1 no switchport ip address 1.1.1.2 255.255.255.0 [code].....
but I find the int g0/1 output traffic only can achieve about 500kbps then I try config below,
interface GigabitEthernet0/1 no switchport [code]....
I find int g0/1 output traffic only can achieve about 5Mbps,but if I change "srr-queue bandwidth limit xx" command xx to 20-90,the int g0/1 can achieve normal traffic bps, for example,
interface GigabitEthernet0/1 no switchport [code]...
the int g0/1 output can achieve 2Mbps that is correct,just only when limit set to 10%,the traffic only can achieve half of limit bandwidth.
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
I'm trying to access the CMS administration page from my browser. I've already tried 192.168.0.1 and that brings up my gateway (cable modem from Time Warner).
I upgraded a Catalyst 2950 switch and there wasn't enough room so I deleted the flash. The upgraded went well using tftp. It booted up fine. The I0S version includes crypto. But, I can't access switch via web browser or CNA. Port scan shows port 80 0pen. What am I missing?
Here is the flash. Directory of flash:/ 2 -rwx 112 Mar 01 1993 01:00:48 +00:00 info 3 -rwx 3722814 Mar 01 1993 01:02:58 +00:00 c2950-i6k2l2q4-mz.121-22.EA14.bin 4 drwx 4416 Mar 01 1993 01:03:45 +00:00 html 331 -rwx 112 Mar 01 1993 01:04:19 +00:00 info.ver 332 -rwx [code]....
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
In my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
we are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950 S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end 3750 SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
