Cisco Switching/Routing :: Rate Limit Configuration On 2950
Jun 10, 2012I configured rate limit on cisco 2960 switch sexuss fully, but i could not configure in cisco 2950 (verson 12.1 (22).To confiure the same on 2950
View 4 Replies
ADVERTISEMENT
Cisco Switching/Routing :: High Discard Rate Error From LMS For Switch 2950
Feb 13, 2012As always, the Cisco LMS is keep sending the follwoing high discard error from the Cisco switches WS-C2950T-24:
EVENT ID = 0004SX3
ALERT ID = 00019LF
TIME = Tue 14-Feb-2012 08:56:35 GMT
[Code].....
Cisco Switching/Routing :: VLans Limit On 2950?
Jun 12, 2012I have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
router
|
2950 - vlan 1,2,3,4,5,6,7,8,9,10
[Code].....
Cisco Switching/Routing :: Rate Limit 3560 Outbound To 5mb?
Jun 9, 2013How to rate limit a 3560 inbound and outbound using different QoS methods. I've read about vlan class maps/policy maps, using the rate limit command on the physical interface, using the srr-queue bandwidth command(it's a gig switch so not sure that would work) and marking all packets and then applying QoS. I'm just learning QoS so trying to figure all of this out and find the best way to do things.
Also, I was told to do this because it's not advisable to have a connection to your ISP that is not 10mb or 100mb on a switch, since they are not divisible by 10 and it can cause issues?
Cisco Switching/Routing :: Rate Limit Traffic In 3560
Oct 20, 2011I am using Cisco 3560 as distrubution switch and want to limit port 445 traffic on 1 MB and applied rate limit statment on Gi0/1 port but switch unable to limit said traffic.rate-limit output access-group 120 1024000 128000 128000 conform-action transmit exceed-action drop.
View 25 Replies View RelatedCisco Switching/Routing :: Rate Limit 2960 Port To 1 MB
Nov 5, 2009To rate limit the 2960 switch port to 1 MB.I have made the specified chnages , how ever still it is reaching more tha 1 MB
Hard coded the bandwidth of port to 10 MB and have applied the specified command srr-queue bandwidth limit 10.
Cisco Switching/Routing :: WS-C3560-24PS - Rate Limit And QoS
Mar 4, 2012I am having an issue with VoiP phones giving me an insufficient bandwidth message. I have three remote locations connected to our main building using 2 Mb point to point ethernet solutions through TWC. Each remote location has a Cisco WS-C3560-24PS running IOS C3560-IPBASE-M, version 12.2(25) and have the cable modems plugged into port 1 on them. The remote buildings are labeled 192.168.101.xxx, 192.168.102.xxx, and 192.168.103.xxx. There are 14-16 VoiP phones in each remote building. The main building being in the subnet of 192.168.100.xxx. I have the 3560s connecting to a single port on a 2801 in the main building, all using the subnet of 192.168.253.xxx The phone server sits in our network at 192.168.100.203. I have created the ACLs, class maps, and policy maps on all of the equipment.
For the remote buildings I have the following:
ACL
===========
Extended IP access list VOIP
permit tcp any host 192.168.100.203 dscp ef
permit tcp any host 192.168.100.203 eq 5566
[Code]....
I have put a hub in to capture traffic via Wireshark to see if DSCP flags are being appropriately marked and I do see that all VoiP packets are getting marked with as EF. However, I have been receiving phone calls from people in the remote buildings stating that their phones will cut out, flash Insufficient Bandwidth on the LCD displays and then the call will cut back in. I am wondering if the 2801 is not applying QoS with the rate-limits in mind since it is set to 100 Mb, or is it an issue with trying to take 3 remote locations and bring them down into 1 port on the 2801?
Cisco Switching/Routing :: 6509 - IP Multicast Rate Limit
Nov 26, 2012How is it i can implement the command 'ip multicast rate-limit out group-list <access-list>' but i get the error "ip multicast rate-limit" command is not supported on 6509?
Is it an IOS limitation or a limitation of the switch series and subsequently can't be used at all?
Cisco Switching/Routing :: 6509-E - Rate Limit PPS On Interface?
Jun 8, 2013How (and is) it possible to rate limit pps on an interface (physical/logical), on a 6509-E?The porpuse is to protect from attacks which lead to very high pps, bypassing traffic rate-limits, and effecting the device's performance
View 2 Replies View RelatedCisco Switching/Routing :: Bandwidth Limit On 2950 Switch?
Mar 25, 2012I have cisco 2950 catalyst switch, verson IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(20)EA1a, RELEASE SOFTWARE (fc1)
So. for one of my port (FE 0/3) i need to put the bandwith limit 512 kbps, how to configure the above same.
Note:- I configured the below but no effect
1. interface FastEthernet0/3description * CONT TO B-CENTER *switchport access vlan 10switchport mode accessbandwidth 1024speed 10
2. and there is no srr bandwidth limit option for 2950, but the same is working for 2960.
Cisco Switching/Routing :: 6513 - Rate Limit And Traffic Shaping?
Mar 21, 2012I am looking for step-by-step configuration on how to enable rate-limit and traffic shaping on Cisco 6513 vlan interfaces. I am not able to find this particular document on CCO.
View 3 Replies View RelatedCisco Switching/Routing :: 3560 Rate-limit Vs Policing And Shaping
Nov 27, 2011I am configuring a 3560 to provide internet access for our customers and I need to make sure they don't use more bandwidth than they have contracted for.I see that the 3560 supports the rate-limit command, but was told that I should use traffic shaping and policing along with access lists to manage the bandwidth.Is there a reason that I should avoid using the rate-limit command - it looks much simpler.
View 10 Replies View RelatedCisco Switching/Routing :: Rate Limit Trunk Port On 3750?
Oct 3, 2012Is it possible to rate limit on a L2 trunk port on a 3750?
current port config and ios are as follows;
interface GigabitEthernet1/0/50
description *** Connection to Fiber Link ***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,172
switchport mode trunk
end
flash:c3750-advipservicesk9-mz.122-46.SE.bin
i was wondering if the "srr-queue bandwidth limit 10" command would work to limit the output from this interface to be 10 % of the port bandwidth and then the same command could be done on the other side.
Cisco Switching/Routing :: 3750x Switch Port Rate Limit
Oct 8, 2012I want to limit the bandwidth going to remote site on the switch connecting to our netapp.We have a 4 port channel group setup on our 3750x switch going to our netapp storage. We have a Wan 100mb link to our remote site and we want only 60MBs of that link to be used for Netapp traffic all other local traffic needs to use the full amount of the bandwidth to the netapp.
Is possible to allocate bandwidth in this way and how would I go about this? We dont have access to the routers for the link and they plug directly into a port on our cisco.
Cisco Switching/Routing :: 3750 - SRR-Queue Bandwidth Rate Limit?
Feb 25, 2013If I have an interface configured as follows (on a Cisco 3750 Switch)
Interface gi 1/0/24
Bandwidth 100000
And then added the following command
srr-queue bandwidth limit 40
Would the result be 40% of the physical 1Gbps interface or 40% of the 100Mbps Bandwidth set under the interface bandwidth command.
Cisco Switching/Routing :: SPAN SIP And Wireshark 2950 Configuration
May 26, 2013I have cisco 2651 with one L3 interface ip 172.26.18.200. This Cisco is gateway from E1 PRI (PBX Aastra MX-ONE TSW) to SIP (Asterisk). This cisco 2651 connected to cisco 2950 in port Fa 0/12. Fa 0/12 is in VLAN 518 (dot1q).
On cisco 2950 i made next commands:
# monitor session 1 source interface Fa 0/12 both encap dot1q
# monitor session 1 destination interface Fa 0/9
#sho monitor session 1
[Code].....
Cisco Switching/Routing :: Trust Dscp Configuration On 2950
Jan 8, 2013i have Catalyst2950SI with iOS12.1, connect a wifi-access-point to f1/1(dot1q trunk port),and connect another L2SW to f1/2(dot1q trunk port),and IP phone, MobileCamera connects to wifi-access-point,IP phone has dscp=40 value on its own packet,but MobileCamera doesn't have any dscp value or cos.now, i wanna do QoS by that dscp, So i type as below,
interface 1/1
switchport mode trunk
mls qos trust dscp
interface 1/2
switchport mode trunk
mls qos trust cos
Cisco Switching/Routing :: Reset Password And Retrieve Configuration On Switch 2950 And 3560?
May 26, 2013how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies View RelatedCisco WAN :: 3700 Rate Limit In Interface
Feb 24, 2011I am not able to disable rate limit comand from Cisco 3700 series router. I have tried with no rate limit command in the interface .Command is taking but still the rate limit comman in the interface.
View 2 Replies View RelatedCisco WAN :: Rate Limit On 3750v2 SVIs
Dec 6, 2011I have a stack of Cisco 3750v2 switches with 8 VLANs (one per customer) and 8 SVI's (again, one per customer). I am trying to apply rate limiting to the SVI's of each vlan for both input and output traffic. This is my SVI configuration for one such VLAN (I have substituted the real IPs for prviate IPs for the purposes of this example) -
interface Vlan30
description ****CUST-C-VL30-SUBRATE-CAR-10M****
ip address 192.168.30.250 255.255.255.0
[Code]...
Based on this and the speed tests I am performing from within the VLAN i am receiving the full bandwidth and not what should be assigned based on the rate limiting. Have I missed anything as far as the configuration goes?
Cisco Firewall :: ASA 5510 Ver 8.2 Rate Limit
Jan 17, 2012I'm trying to limit one of my inside hosts, since it's been a little of a hog. I have 3Mb available from my ISP via 2x T1. I'm testing this on a computer in a lab:
PC 10.10.10.10------Cisco2960-------- 10.10.10.1 Inside - ASA - Outside 208.66.x.1------------------------208.66.x.2-Cisco 2811-2xT1
Here's what I've tried so far, please see text in red:
***global (outside) 1 208.66.x.115
***nat (inside) 0 access-list No-Nat
***nat (inside) 1 0.0.0.0 0.0.0.0
[Code].....
It didn't work... I was able to max the bandwidth again. I also tried to apply service-policy to inside int, which didn't make a difference.
Cisco WAN :: 3900 - IP Multicast Rate-Limit
Feb 16, 2012I run streaming multicast video cameras on my network. I stumbled upon the command ip multicast rate-limit. When I configured a test setup in my lab (multicast camera source and a few routers) and tried the command it simply did not work. Moreover, when I went to use the command on a 3900 router in my lab, it was not there.
I take it this command has been deprecated?
Cisco :: ASR 1013 - Command Of Rate Limit On A Sub Interface
Jul 23, 2012I am looking for the command of rate-limit on a sub-interface in cisco asr 1013.
Cisco IOS Software,
IOS-XE Software (X86_64_LINUX_IOSD-ADVENTERPRISEK9-M),
Version 15.2(2)S, RELEASE SOFTWARE (fc1)
IOS XE Version: 03.06.00.S
If it is possible in Cisco asr 1013. If yes then what are the commands.
Cisco WAN :: Applying Rate-limit To Bridge On 1841
Sep 22, 20111841 - IPBASE 12.4.7d
We provide internet access for a number of clients sitting on our WAN, at present they have un-restricted access to the full bandwidth of our 1Gb internet pipe. As they are only paying for a proportion of that we want to set a Mbps limit on the clients, and idealy the device should be transparent between our router and the clients.
I have been trying to set up rate limits on a bridge on our 1841.
#
bridge 1 protocol ieee
bridge 1 route ip
bridge 1 bridge ip
[Code].....
I have tried many combinations but can't get this to limit the traffic, the client still draws as much as they can.
Does rate limit work on bridged interfaces? or am I going to have to try it routed instead?
Cisco Firewall :: 5515 - Way To Rate-limit By IP Address?
Jun 3, 2013Worried about denial-of-service attacks. They have 11 vm's that share a connection and want to set it up so that there is a maximum amount of traffic allowed to hit each vm, so if there is a DDoS attack it will only affect that one VM instead of all the VM's on the same connection.
What is the best way to go about this from the ASA? This is behind a 5515 with asa code version 8.6. Is there a way to rate-limit by ip address?
Cisco WAN :: 886VA-K9 / Qos / ATM / VoIP - Where To Rate-limit / Police
Apr 8, 2013Setup:
Cisco 886VA-K9
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)
This router has two VLAN's on one Ehternet interface
VLAN1: data
VLAN2: voice
The WAN connection is a regular DSL line with PPP.
Modem FW Version: 120306_1254-4.02L.03.B2pvC035j.d23j
Modem PHY Version: B2pvC035j.d23j
Output of show interface brief:
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM up up
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
[code]....
We all know you can't manage data traffic on the internet since your not in control of both sides of the link. So only queuing would not be a good practice IMHO. I was thinking on just rate-limit or police data-traffic so Voice always has bandwidth available when needed. I've did tried to rate-limit on the ATM0 interface, but no luck. Voice was still very bad.
My question is: where to rate-limit the data traffic? On the VLAN interface, the ATM interface, DIALER interface?
Cisco 1800 - Router Bandwidth / QOS And Rate Limit
May 21, 2012I apologize in advance if this is a novice inquiry, but our company just switched from Point-to-Point T1's to Metro Ethernet.
On one point-to-point, from our main office to one of our high profile locations, we had two bonded T1's. Now this site has a 3 Mbps Metro-E link, but it's being over-saturated. I don't know what type of QOS implementation our T1 provider had, but it prevented flooding. Now, I'm getting horrendous latency as the office peak hours approach since there is no QOS on the mesh by our Metro-E providers.
Ultimately, my question is: what's the best way to set a Fast Ethernet port on a Cisco 1800 series router to limit all bandwidth to 3 Mbps? At the moment, I don't have a preference in which traffic takes priority. I tried the rate-limit command, along with a speed calculator I found online, but that slowed the network down immensely.
Cisco Application Networking :: ACE A2 (3.4) - Set A Rate-limit Connections Per Sec From Any Source IP
Jan 28, 2012ACE A2(3.4). Is it possible to set a rate-limit connections per sec from any source IP. For example, if a client is trying to GET a web page 10 time per sec I will send a reset or drop that connection.
View 1 Replies View RelatedCisco Switches :: SG300 To Configure VLAN Rate Limit
Apr 14, 2013I have a Cisco SG300 small business switch and 541 APs. There are 2 VLANs in our network. One must be limited by bandwidth. How to configure vlan rate-limiting on SG300? And describe CIR & CBS.
View 1 Replies View RelatedCisco Routers :: RV120W - QoS Bandwidth Rate Limit Don't Work
Aug 21, 2011Buy a router RV120W, and one of the reasons is limit of bandwidth (QoS). I set up a profile of 1-256 kbps limit, and apply it to the only VLAN that is configured, but does not work and can navigate using the full bandwidth of the internet connection. My firmware version is 1.0.2.6
View 8 Replies View RelatedCisco Firewall :: 3389 Any Ability To Rate Limit Connections?
Dec 9, 2012I'm trying to determine whether Cisco has any equivalent (in any platform) to some of the existing firewall rules within our iptables infrastructure. [code] What this does, is allow port forwards on port 3389/rdp. However, if a single IP opens too many connections within a timeframe, it starts dropping new ones.This is a critical requirements for certain security scenarios, such as preventing RDP brute forcing. A similar principle can be applied to 22/ssh.I've had a look around, rate limiting searches generally land me on QoS based discussions. I've seen people ask similar questions and get referred to CBAC. Whilst I can see similarly worded functions there such as limiting "half open" connections, I don't see anything there that limits the actual number of connection attempts you can make.
View 1 Replies View RelatedCisco Firewall :: ASA 5510 - Rate Limit The Internet Bandwidth / Speed?
Jul 29, 2012In ASA 5510. How I can limit the users in (VLAN 20) to use the internet with a limited Bandwidth/speed with 3 mbps upload and 5 mbps download?
In case the outside interface (Native vlan) which is connected to the ISP and have a bandwidth/speed of 30 mbps upload and 50 mbps download.
Cisco Firewall :: ASA5510-BUN-K9 / Find Out Rate-limit Drop Source Ip?
Nov 22, 2011I have two ASA5510-BUN-K9 Fws and I am planning to buy 2 x L-ASA5510-SEC-PL= to put them in HA.I was wondering if the support contract that I curently have for the two ASAs is still valid or do I have to buy any support upgrade?
View 1 Replies View Related