Cisco Switching/Routing :: Trust Dscp Configuration On 2950
Jan 8, 2013
i have Catalyst2950SI with iOS12.1, connect a wifi-access-point to f1/1(dot1q trunk port),and connect another L2SW to f1/2(dot1q trunk port),and IP phone, MobileCamera connects to wifi-access-point,IP phone has dscp=40 value on its own packet,but MobileCamera doesn't have any dscp value or cos.now, i wanna do QoS by that dscp, So i type as below,
interface 1/1
switchport mode trunk
mls qos trust dscp
interface 1/2
switchport mode trunk
mls qos trust cos
View 10 Replies
ADVERTISEMENT
Jul 4, 2012
I am reading through a QOS Document and they want me to trust the DSCP value from an IP phone (Siemens) but UN trust the PC DSCP value. How can I trust one thing but not the other? I am using a 2960 Cisco switch with IP base IOS.
View 2 Replies
View Related
Dec 24, 2012
i would like to know the possibility to use mls qos trust dscp with service-policy in the IOS ver.12.2(25)SEE2.The specific version is not possible to configure like below.
Cat3750(config-if)#do sh run int f1/0/1
Building configuration...
[code]....
View 8 Replies
View Related
Sep 22, 2011
I have a problem with the command mls qos trust dscp, I used the ios c2800nm-ipvoice_ivs-mz.124-25f.bin but i can not enable dont show me the complete command in the interface Ethernet o Giga. I want to configuring mls qos trust dscp.
View 1 Replies
View Related
Feb 13, 2013
I want to know what the default behavior about the command 'mls qos trust dscp' under router platform interface. the router is ASR1000 series.we don't need to put above command line to trust dscp in case of router? otherwise, we have to add it as welll as like switch platform.
View 4 Replies
View Related
Jun 10, 2012
I configured rate limit on cisco 2960 switch sexuss fully, but i could not configure in cisco 2950 (verson 12.1 (22).To confiure the same on 2950
View 4 Replies
View Related
May 26, 2013
I have cisco 2651 with one L3 interface ip 172.26.18.200. This Cisco is gateway from E1 PRI (PBX Aastra MX-ONE TSW) to SIP (Asterisk). This cisco 2651 connected to cisco 2950 in port Fa 0/12. Fa 0/12 is in VLAN 518 (dot1q).
On cisco 2950 i made next commands:
# monitor session 1 source interface Fa 0/12 both encap dot1q
# monitor session 1 destination interface Fa 0/9
#sho monitor session 1
[Code].....
View 2 Replies
View Related
May 26, 2013
how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies
View Related
May 8, 2012
I have a question which i am unsure of, on the 6500 i know i can set mls qos trust to cos or dscp since I don't have any trunks configured on that switch that i want to trust cos most of my ports trust dscp instead. The question is will packets coming in or going out at L3 with the TOS bits set get placed in the correct in/out queue. For example if a packet comes in on a port with a mls qos trust dscp and has the TOS set to XX will this XX get mapped to the correct COS value based on the default dscp to cos map and end up going out the correct queue which handles that specific COS number?
I mainly asked this because i saw the following on the cisco site and again i am suing dscp trust and not cos.
Weighted Round Robin (WRR), Deficit Weighted Round Robin (DWRR) and Shaped Round Robin (SRR). WRED and all the Round Robin scheduling options use the priority tag (CoS) inside an Ethernet frame to provide enhanced buffer management and outbound scheduling.
View 2 Replies
View Related
Oct 7, 2012
We have QoS configured throughout the company, but the standard config we have applied across the 3750 switches only includes the below: We have IP phones (not cisco) attached that are marking with EF, and the PC is an untrusted end device (so needs to be by default marked as zero).Is the above enough to trust VOIP DSCP EF without resetting it to DSCP 0, or do I also need to add a trust line (i.e.: mls qos trust dscp)?
View 2 Replies
View Related
Aug 1, 2012
Are there any differences between the autoqos commands on a WS-C2960S switches (or in any other series)? Follow the commands:
- auto qos trust
- auto qos voip trust
I was checking the documentation on this link:
URL
And couldn't find any great difference between the two commands, as far as I could see they'll set the Ingress and Egress queues the same way.
Are there any differences between those two commands (auto qos trust and auto qos voip trust)? If so, when should I use one and the other?
View 2 Replies
View Related
Jun 20, 2012
I have some 2960 switches with Lan Lite ios in my infrastructure.And I try to configure them to support "trust device cisco-phone" and "switchport priority extend cos 0" on ports with cisco phones.But LAN Lite image does not support "mls qos trust device cisco-phone".can I use any workaround to trust cos of cisco phone and to remark PC traffic with cos 0?
View 1 Replies
View Related
Oct 27, 2011
I've just been testing QOS on 3560 with version 15.0(1) and it seems the the default qos trust behavior on access ports has changed. By default the trust state of a port is not to trust anything, however rather than rewriting the DSCP value of the incoming packets and settign it to 0 the switch now seems to leave the DSCP value unchanged.
SW04-C3560(config)# do sh mls qos int g0/2
GigabitEthernet0/2
trust state: not trusted
trust mode: not trusted
trust enabled flag: ena
[Code]......
View 4 Replies
View Related
May 15, 2013
I am getting a very strange problem where 4500 switch is remarking the packet with dscp 1 to 0.
Let me explaint the setup. I have two PCs connected on same switch but on different modules. PC1 is conencted to Gi4/19 and PC2 is connected to
Gi2/43. Both the ports has been configured to trust the dscp. Below are the configuration:
interface GigabitEthernet4/19
switchport access vlan 6
switchport mode access
[Code].....
View 7 Replies
View Related
Jul 21, 2012
i did on cisco 2960S switch at user ingress interface. but the marking is not showing in show policy-map interface gig 1/0/10 interface and ACL is not showing any match.
I also had a config reference from 2960S cisco guide.
access-list 103 permit tcp any any eq 80
access-list 104 permit tcp any any eq 23
access-list 105 permit icmp host 172.24.68.4 any
class-map IN_HTTP
match access-group 103
class-map IN_TELNET
match access-group 104(code)
View 1 Replies
View Related
Jan 29, 2012
I have a pair of Nexus 7K's running 5.1(3). I have a handful of edge devices that I need to mark ingress traffic, and need to mark both DSCP and CoS. Right now, I have a working config that marks DSCP appropriately.While that works dor DSCP, the MQC will not allow me to mark both DSCP and COS in the same class, and unlike IOS, it appears that Nexus does not have a default DSCP-to-COS mapping. My understanding is this can be solved using table maps, but I don't see how that can solve my problem in this specific scenario (it appears I can do marking or table-map mutation, but not both?). How I can accomplish both?
View 5 Replies
View Related
Sep 6, 2012
there is something I find strange on C6500 about QoS: C6500 derive an internal DSCP value for it's internal use, but when configuring the qos mapping on output interfaces, only a cos value (I guess, an internal cos value) can be used. Is it a misunderstanding from me, or is it really illogic?
View 2 Replies
View Related
Apr 29, 2012
I've been working on a 3560 that doesn't seem to map dscp values to a new value: mls qos map dscp-mutation ToR1 22 24 to 46
[Code]....
On the router on the other side, I created an acl that matched on dscp 46, but it doesn't match on it. I've tried moving the mutation map to the ingress interface and I've tried setting dscp with a service policy instead of marking COS and using internal dscp. Where is the mutation map supposed to be placed: ingress or egress? Also, I added an entry in the acl on the router to see if I was mapping to dscp 24, and I am:
[Code]....
So it seems like the mutation map is being ignored completely. Any reason why?
View 7 Replies
View Related
May 26, 2013
I have a problem with dscp preservation on a WS-C3750X-48 catalyst; in my little diagram, his name will be SW2, so I have this:SW1 <-> SW2 <-> RT1. some phone connected to SW1 mark with dscp EF (46) the voice traffic.The "mls qos" was enabled on SW1 and SWt. The interlink switch ports has the "mls qos trust dscp" option, the phone port and the router port also.And the problem is I can see the dscp marking on the SW2 when I span the voice vlan on this switch but the dscp was removed ( DSCP set to 0) on the router port ( span on the router port for look )If I made also a packet capture on the router RT1, I see the DSCP was effectively reset to zero.If I disable the "mls qos" on SW2, of course all is fine and the dscp was preserved and forwarded to the router. [code]
View 2 Replies
View Related
Mar 14, 2012
I am trying to mark http packets from a web server with DSCP ef, but when I am doing a traffic capture all http packets have tos 0x0.I am able to mark UDP and ICMP packets originated from this server, but not any TCP traffic.The web server is in VLAN 20This is my config mls qos ip access-list extended MARK-HTTP-ACL permit tcp host 10.10.10.10 eq www. [code]
View 4 Replies
View Related
Oct 26, 2011
I'm working on a catalyst c3750 and for my work i need to prioritize certain streams independent of their bandwith usage.
The streams are the following:
- voice
- video
- data
I created policy maps based on vlans like below:
policy-map VOICE
class class-default
set precedence 5
policy-map VIDEO
[Code]...
View 7 Replies
View Related
Nov 28, 2011
I am begining to work to apply Qos on switchs (C2960 & C6500), and I still have a doubt about the necessity to consider the cos value. I indeed want to apply Qos for ToIP, Video, perhaps create a scavenger class, ans in all cases, I classify my packets with TCP/UDPB port and mark them with DSCP. So is it really necessary to study all the DSCP/CoS mapping problematics ? Is it not possible to make the configurations only on the base of the DSCP field?
View 3 Replies
View Related
Feb 16, 2012
When configuring QoS on 3750s/3560s, we're mapping packets to particular interface output queues with commands such as: [code] The command to see what's actually being enqueued, dropped, etc. is: [code]
Note that these queues are numbered 0 - 3, and not 1 - 4. We've been assuming that the first queue number in the "mls qos" (i.e., 1) command maps to the first queue (i.e., 0) in the "show mls qos" command.
View 1 Replies
View Related
Jan 20, 2013
I have a Nexus 5500 which is the core of our network and we have access layer switches uplinked to it. I know by default the qos markings will be trusted.
1. On a trunk uplink from an access layer switch to the Nexus, I have "mls qos trust dscp". Will the DSCP marking be preserved when it reaches the Nexus?
2. How do I do prioritization of voice traffic on an uplink on Nexus based on DSCP EF?
View 3 Replies
View Related
Dec 20, 2011
I have made some test and i noticed that qos input policy does not classify the icmp packet based on their dscp.The "match dscp ef" or "match precedence 5" is not working only the "match protocol icmp" shows hits.
We need to classify the different icmp packets based on dscp ( TOS ) for measurement purpose.CISCO 7200, 12.4.25d and 12.4.20T have a same behavior.
View 6 Replies
View Related
Apr 3, 2013
How the dscp-cos or cos-dscp mapping takes place in c892 router? There is no command like "sh mls qos maps" in c892 like we have in c2951 or c3925.
View 3 Replies
View Related
Feb 11, 2012
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies
View Related
Jun 22, 2012
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies
View Related
Apr 25, 2013
I have a server windows 2008 that I would like to have a nic teaming configuration, the server has two nics, each nic is connected to a different switch. One is connected to cisco 2960 and the other is connected to cisco 2950. I have read here in forums about nic teaming but using the same switch. I have not found using different switch. Is this possible?
View 1 Replies
View Related
Jan 11, 2012
2950 switch has a IOS on flash , but i would like to set the swith like...
1. switch IOS to be loaded from TFTP server .if it fails
2. Loaded from local flash IOS1 , if it fails
3. IOS loaded from local flash IOS2.
does 2950 switch support this feature.
View 2 Replies
View Related
Jun 11, 2012
I have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies
View Related
Dec 14, 2011
I have a cisco catalyst 2950 switch (flash:c2950-i6q4l2-mz.121-22.EA1b.bin), in remote location with public IP,how to upgrade ios remotely, by that time running configuration will go?how much down time is required and ?
View 7 Replies
View Related
Jun 12, 2012
I have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
router
|
2950 - vlan 1,2,3,4,5,6,7,8,9,10
[Code].....
View 12 Replies
View Related
