Cisco Switching/Routing :: Does Ip Helper Address Work On A Layer 2 Switch 2950
Jan 9, 2012I would like to know if ip helper-address feature is working on a layer 2 switch (2950,2960) or you should use a Layer 3 switch to do that?
View 7 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Can Layer 2 2950 Switch Be Used As DHCP Server With Its Own Address Pool
Mar 18, 2009Can a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies View RelatedCisco Switching/Routing :: Configure Virtual Circuits On Layer 2 Switch Catalyst 2950
Feb 14, 2013can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies View RelatedCisco Switching/Routing :: DHCP Server Will Work On 2950 / 2960 Switch
Feb 11, 2012With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies View RelatedCisco Switching/Routing :: Determine IP Address Of 2950 Switch?
Aug 13, 2012Do they have a default IP assigned to them?
I'm trying to access the CMS administration page from my browser. I've already tried 192.168.0.1 and that brings up my gateway (cable modem from Time Warner).
Cisco Switching/Routing :: DHCP Request Not Being Forwarded By Helper Address Same VRF 6500?
Feb 22, 2013Version 12.2(33)SXI
int vlan 1
description client vlan
ip vrf forwarding A
ip address 10.1.1.1 255.255.255.0
standby 129 ip 10.1.1.2
standby 129 timers 1 4
standby 129 priority 105
standby 129 preempt
ip helper-address 10.1.2.20
[code]....
dhcp requests are not making it to the dhcp server SAME VRF (ip helper-addres is not doing anything.....)extended vrf traceroutes on udp 67 sourced from vlan2 are fine
I am expecting udp unicast packets on port 67 "giaddr" relay packets on the DHCP server generated and sourced by the relay on Vlan1
eg. Mar 1 01:59:06.731: DHCPD: setting giaddr to 10.1.1.1
This exact setup works in our preprod environment with the same code.Only difference is we run Distributed etherchannel on the 6500's where this doesnt work.
Wireshark on the client I can see the requests being sent Going to check it with debug ip dhcp server to check the relay logs out of production hours.
I have seen so many people say it IS and ISN'T supported on this version of the code.e.g. [URL]
I am aware the helper-adddress should inherit the vrf of the interface ip helper-address vrf command is not supported.The fact it works in the PP environment.... could this be due to the Distributed EtherChanel difference? or just some bug....
Cisco Switching/Routing :: 4500 / 3560 - DHCP Redundancy - IP Helper Address Point To HSRP?
Jan 5, 2012My actual Scenario
1 x 4500 and 1 x 3560?They are gateways of 8 Vlans?They are doing HSRP in each of those Vlans?The 4500 is the Active?There is a DHCP Pool for each of those Vlans on both gateways using "ip dhcp excluded-address" I ensured that the range of provided ips by each DHCP server will not be overlapped Obs.: Reducing the lease time, I ended with the calls bringing related problems.
OK, every thing is blue, every thing is fine.But the network diagram is realy complex(41 switchs, 89 uplinks), and depending of how is the network flow, one or other server answer first or latter.
For many reasons I would like that the secondary DHCP server would answer only if the primary DHCP server goes down.To me, the bigger reason is that DHCP database would be only in one DHCP server.But there is other reasons.
I passed by many frustrated solutions:Try to force a delay on the answer on one of the servers. - Impossible.Try to disable DHCP server, and, using EEM, enable it only if router became active in HSRP. - I couldn't do It.
What I'm thinking now is use the HSRP resource to resolve it.On both routers I would put a "ip helper-address" pointing to an Virtual_HSRP_IP.And depending on which router is the active, him will answer the request.
My first doubt is:Would it work?The second doubt is:Could I use the same Virtual_HSRP_IP that exists on that Vlan(see example 1),or I would need to point it to a Virtual_HSRP_IP in a different Vlan(see example 2)?
Example 1
-----------------------------------
| 4500 |
-----------------------------------
interface Vlan1
ip address 10.10.0.2 255.255.0.0
ip helper-address 10.10.0.1
standby 1 ip 10.10.0.1
[code]....
Cisco Switches :: SF 200-48P / How To Add IP Address Helper Command To Switch
Feb 5, 2012I am trouble shooting a SF 200-48P and I am a bit lost without a CLI not used to the GUI. What I need to know is how to add the IP address helper command to the switch?I have a number of IP phones which are not getting an IP address from DHCP (PCs which are diasy chained off the phones are all working correctly). On the higher end switches I would have added the IP address helper command to the VLAN and that would have sorted it. How to do this on the small business switch.
View 2 Replies View RelatedPossible To Assign Loop Back Address To Typical Switch Port On 2950 Switch
Jan 16, 2011is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies View RelatedCisco Switching/Routing :: 2950 CRC Errors On Switch
Jun 22, 2012One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies View RelatedCisco Switching/Routing :: 2950 Switch Not Allowing To Set Up SSh
Feb 8, 2013After setting up the domain name I try to use the crypto key and it is no where to be located. Below is some of the information I copied from TeraTerm
Switch-1(config)#ip domain-name justin.lab.comSwitch-1(config)#crySwitch-1(config)#cry?% Unrecognized commandSwitch-1(config)#crypto key ?% Unrecognized commandSwitch-1(config)#crypto key ^% Invalid input detected at '^' marker.
Switch-1(config)#?Configure commands: aaa
Cisco Switching/Routing :: Cannot Assign Ip Address To Layer 2 Interface In 878
Apr 19, 2012I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
Cisco Switching/Routing :: Bandwidth Limit On 2950 Switch?
Mar 25, 2012I have cisco 2950 catalyst switch, verson IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(20)EA1a, RELEASE SOFTWARE (fc1)
So. for one of my port (FE 0/3) i need to put the bandwith limit 512 kbps, how to configure the above same.
Note:- I configured the below but no effect
1. interface FastEthernet0/3description * CONT TO B-CENTER *switchport access vlan 10switchport mode accessbandwidth 1024speed 10
2. and there is no srr bandwidth limit option for 2950, but the same is working for 2960.
Cisco Switching/Routing :: 2950 - Can't Access Switch Via Browser Or CNA
Jan 5, 2012I upgraded a Catalyst 2950 switch and there wasn't enough room so I deleted the flash. The upgraded went well using tftp. It booted up fine. The I0S version includes crypto. But, I can't access switch via web browser or CNA. Port scan shows port 80 0pen. What am I missing?
Here is the flash.
Directory of flash:/
2 -rwx 112 Mar 01 1993 01:00:48 +00:00 info 3 -rwx 3722814 Mar 01 1993 01:02:58 +00:00 c2950-i6k2l2q4-mz.121-22.EA14.bin 4 drwx 4416 Mar 01 1993 01:03:45 +00:00 html 331 -rwx 112 Mar 01 1993 01:04:19 +00:00 info.ver 332 -rwx [code]....
Cisco Switching/Routing :: 2950 Switch Management IP Change?
Nov 4, 2012I am planning to change the management IP (VLAN 5) to one of my Cisco 2950 switch, Here I am creating a new VLAN101 and assign new IP
When I am doing this VLAN 2 is going admin down.
Cisco Switching/Routing :: SF 300-48 Layer 3 Switch Tried To Configure To Use
Aug 24, 2011I got one SF 300-48 layer 3 switch I tried to configure to use it in the office network.Unfortunately I'm unable to configure the VLAN settings.I need port one for input(VLAN2),port 7-15 for another vlan(vlan3) also need to connect with the vlan 4.port 15 is another vlan(vlan4) this is for wireless.Other ports are static.It doesn't get any connections with other vlans.I wish to know how to configure vlans in GUI mode.I tried , But I can't get the Vlan setting correctly.Also,I need to know how to communicate both vlans in GUI mode.
View 8 Replies View RelatedCisco Switching/Routing :: Layer 3 Switch And ASA 5550
Apr 29, 2013I created a lab and I have a few issues. One with a layer 3 switch and another with a ASA 5550.
1. Layer 3 switch: I have created multiple Vlans and I am able to route between them. I can ping the switch IP but not the default gateway to the ASA. I did a tracert of the default gateway of the ASA and once I am past the Vlan gateway it fails.
2. On the ASA 5550 I created the Vlans on sub-interfaces but still cannot get to the internet. ASA config is below the switch config.
Cisco Switching/Routing :: 3550 / Layer 3 Switch Not Routing?
Apr 26, 2012I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
Cisco Switching/Routing :: Setup Same Console Password In 12 Switch 2950
Nov 3, 2011My requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
Cisco Switching/Routing :: 2950 Switch Booting Through Monitor Mode
Jul 17, 2012I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies View RelatedCisco Switching/Routing :: 2960 - Identify Layer 2 Or 3 Switch?
Feb 9, 2012I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
Cisco Switching/Routing :: Can Use Switch 3750 As Router Layer 3 Without NAT
Jan 13, 2013I've created a scenario using a 3750 cisco as core switch ad other 6 switch model 2900 in access level.my problem is this, the router is not a cisco router, and this router is not able to make NAT on more than one subnet.Into the core switch I've created 4 VLAN and I must to give internet access to 3 of them, 192.168.0.0/24 (vlan1), 172.16.0.0/24 (vlan2), 172.17.0.0/24 (vlan3).I've connected the switch to router via gigabit ethernet 0/1 and I've assigned to this interface ip address 192.168.10.2, the router ip address is 192.168.10.1, Switch ip default-gateway is router ip address 192.168.10.1, ip default route is 0.0.0.0 0.0.0.0 192.168.10.1 I've enabled ip routing feature and I've set no switchport feature to interface gigabit ethernet 0/1.From core switch I can ping router ip address but I can't make it from all other user, and the users not able to have internet access.
Below the switch configuration (only necessary strings)
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code].....
Cisco Switching/Routing :: 3500XL - How To Manage Layer 2 Switch
Sep 5, 2012My understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies View RelatedCisco Switching/Routing :: 3560 DHCP In Layer 3 Switch
May 25, 2012I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.
Cisco Switching/Routing :: Catalyst 4500 As Layer 2 Switch But With VRF?
Oct 16, 2012is it possible to run a Catalyst 4500 as pure Layer 2 Switch, i.e. disabling "ip routing", but still managing the switch via Fa1, i.e. the defautl mgmtVrf vrf ?I tried the following:
!
no ip routing
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address 192.168.1.1 255.255.255.0
!
ip route vrf mgmtVrf 0.0.0.0 0.0.0.0 192.168.1.254
ip default-gateway 192.168.1.254
I was not able to reach the Switch even from the same subnet. Only after enabling ip routing I could manage the Switch. I haven't found any command to set ip default-gateway for a vrf. Any workaround to keep routing disabled, but still manageable via VRF?
Cisco Switching/Routing :: User Based Bandwidth Limitation On 2950 Switch?
Feb 12, 2012I have a cisco 2950 switch, connected with 4Mbps of internet and number of users will access the internet. There is no restraction on bandwidth limit for users, if any body use high download the remaining users are facing the slow browsing problems.
So, if i can put a bandwidth limitation for every users the problem will be solved. how to restract the bandwidth on user bases.
Cisco Switching/Routing :: Configure 802.1x RADIUS Authentication On 2950-24TT-L Switch?
May 3, 2013I am trying to configure 802.1x RADIUS Authentication on cisco 2950-24TT-L Switch. I am using following set of command as given below
Switch# configure t
Switch(config)# aaa new-model
Switch(config)# aaa authentication dotx default group redius
Switch(config)# dot1x system-auth-control
Switch(config)# inter fasteth 0/1
Switch(config)#dot1x port-control atuo
I am facing problem dot1x command is not working on interface.
Cisco Switching/Routing :: 3560G And 2950 Switch Trunk Discard Errors
Apr 15, 2010I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
Cisco Switching/Routing :: High Discard Rate Error From LMS For Switch 2950
Feb 13, 2012As always, the Cisco LMS is keep sending the follwoing high discard error from the Cisco switches WS-C2950T-24:
EVENT ID = 0004SX3
ALERT ID = 00019LF
TIME = Tue 14-Feb-2012 08:56:35 GMT
[Code].....
Cisco Switching/Routing :: Login To 2950 Switch And Modify VLAN Entry On It?
Nov 3, 2011In my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
Cisco Switching/Routing :: Configuring OSPF On A Layer 3 Switch 3560G
Apr 12, 2013Configuring OSPF on a catalyst 3560G Switch to connect to our building next door by way of fiber. The other two switches in the other building are running OSPF, I am trying to connect to the other building and access a server which is on a switch running OSPF. I am trying to configure the switch here to run OSPF and be able to see the neighbor, but currently can't although I've identified the networks. Maybe I'm missing something, I've followed the instructions but something is not right.
View 15 Replies View RelatedCisco Switching/Routing :: 3560 / Connectivity From Layer 3 Switch To Firewall?
Nov 29, 2012RACK 1 is the old rack and NEW RACK is the rack which is going to be procurred for some new Servers. All the Servers in the RACK 1 has a default gateway as PIX Inside IP. As of now the 3560 Switches acts as Layer 2 and does not have L3 IP routing enabled. How can I enable conenctivity between 192.168.36.0 range and 192.168.57.0 range wihtout making any change to current PIX inside IP address 192.168.57.1?Is it possible that I can enable IP routing on the 3560 Switches , create interface VLAN 36 and since already Switch 2 has it 's default gateway as 192.168.57.1 , Would the traffic from 192.168.36.0 be routed to 192.168.57.1 ? Or do I need to create static route for that ?Since L3 Routing is not enabled and since the 3560 Switches are just acting as L2 , the VLAN 2 - 192.168.57.0 range does not have any interface VLAN configured. When it is changed I would need to create interface VLAN 2 on 3560 Switches?
View 18 Replies View RelatedCisco Switching/Routing :: Default Password For 2960-C Layer 3 Switch
Dec 23, 2012I just received a Catalyst 2960-C (WS-C2960C-8TC-L R) switch and I am unable to sign into its web GUI in order to configure it. I've tried both the Cisco Network Assistant and Internet Explorer and I am unable to log in either way. The documentation provided by Cisco states that the default password is simply cisco and that a username is unnecessary. Needless to say, it doesn't work. I've also Googled for other default passwords (such as cisco-cisco as the username-password), none of which worked either. I've also tried resetting the switch back to its factory default a few times.
View 8 Replies View Related