Cisco Switching/Routing :: 3560 / Connectivity From Layer 3 Switch To Firewall?
Nov 29, 2012
RACK 1 is the old rack and NEW RACK is the rack which is going to be procurred for some new Servers. All the Servers in the RACK 1 has a default gateway as PIX Inside IP. As of now the 3560 Switches acts as Layer 2 and does not have L3 IP routing enabled. How can I enable conenctivity between 192.168.36.0 range and 192.168.57.0 range wihtout making any change to current PIX inside IP address 192.168.57.1?Is it possible that I can enable IP routing on the 3560 Switches , create interface VLAN 36 and since already Switch 2 has it 's default gateway as 192.168.57.1 , Would the traffic from 192.168.36.0 be routed to 192.168.57.1 ? Or do I need to create static route for that ?Since L3 Routing is not enabled and since the 3560 Switches are just acting as L2 , the VLAN 2 - 192.168.57.0 range does not have any interface VLAN configured. When it is changed I would need to create interface VLAN 2 on 3560 Switches?
View 18 Replies
ADVERTISEMENT
May 25, 2012
I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.
View 3 Replies
View Related
Feb 26, 2012
I have a switch layer 6500 series connected to a firewall, the port configuration between them is layer 2, in another words I do not configure an IP address in the Cisco switch port to conected it in the firewall, but when a apply a policy on firewall it lose communication with others vlans, just the vlan that is connected between the switch and firewall works, attachment the design. I think that is necessary to configure the connection between the firewall and switch as layer 3 ( a port with IP address in the switch), but I would like to know why? The switch is configured with about 10 vlan and it is a inter vlan routing, a default route is configured in the switch where the gateway is the firewall.
View 5 Replies
View Related
Mar 17, 2013
I found that when I enabled layer 2 auto QoS in 3560 switch, I need to wait so much time to open a file in network drive. Howerver, when I disable the Qos. It can improve a lot. I have used a sniffer to capture the packet to see. Those default packet is in DSCP 0. Therefore, I think majority packet will drop to queue 4. How can I increase the buffer and threshold in order to improve queue 4 performance.
View 1 Replies
View Related
May 23, 2012
I been practicing with the configuration of layer 3 etherchannel configuration and i am facing a problem here. I have two 3560 switches and i want a layr 3 ether channel configuration setup between the first 2 ports of bothe the switches. I assign IPs to the Port-channel 1 of both the switches "10.1.1.1 /24 and 10.1.1.2 /24" but i am unable to get a successful ping. what am i doing wrong. below are the configs for bothe of my switches.
3560_1
Building configuration...
Current configuration : 1274 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
[code].....
View 2 Replies
View Related
Apr 9, 2012
I am setting up a link between buildings that uses wireless links. I'm using Layer 3 routed ports on 2 3560 switches to handle the routing between sites. Normally I would just put these in a /30 and then the switches handle the rest. However, the wireless access points have a web interface for managing them that I want to be able to access, but it's only available on the single NIC that also carries traffic. What would be the best way of making this work? Should I make the link a /29 and give the access points an IP in the same range? If this is the case what do I use for the default gateway for the access points?
I have included a diagram to try to explain the issue clearer. The IP addresses in black are what I would do if this were a standard cable (and indeed this will work, but I wont be able to access the admin interface of the wireless AP) and the red ip addresses are the alternative if I use a /29 (but as I said, I'm not sure what to use for the default gateways).
View 1 Replies
View Related
Apr 22, 2011
can i use normal two L3 Switch(3560) for BGP Multihoming with 2 different isp
View 4 Replies
View Related
Dec 13, 2011
From the multiplexer 9 ethernet connections are terminating in Cisco 2960G 24 port swith and it is connected through fiber uplink to one Cisco 3560G 48 port switch in first floor, which is connected to server.
How I will configure the 3560G to make communicate with 2960G and bring all these 9 ethernet connections to server. All the 9 connections are from different IP. and server also have different IP.
View 1 Replies
View Related
Aug 24, 2011
I got one SF 300-48 layer 3 switch I tried to configure to use it in the office network.Unfortunately I'm unable to configure the VLAN settings.I need port one for input(VLAN2),port 7-15 for another vlan(vlan3) also need to connect with the vlan 4.port 15 is another vlan(vlan4) this is for wireless.Other ports are static.It doesn't get any connections with other vlans.I wish to know how to configure vlans in GUI mode.I tried , But I can't get the Vlan setting correctly.Also,I need to know how to communicate both vlans in GUI mode.
View 8 Replies
View Related
Apr 29, 2013
I created a lab and I have a few issues. One with a layer 3 switch and another with a ASA 5550.
1. Layer 3 switch: I have created multiple Vlans and I am able to route between them. I can ping the switch IP but not the default gateway to the ASA. I did a tracert of the default gateway of the ASA and once I am past the Vlan gateway it fails.
2. On the ASA 5550 I created the Vlans on sub-interfaces but still cannot get to the internet. ASA config is below the switch config.
View 7 Replies
View Related
Apr 26, 2012
I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
View 11 Replies
View Related
Feb 9, 2012
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
View 5 Replies
View Related
Jan 13, 2013
I've created a scenario using a 3750 cisco as core switch ad other 6 switch model 2900 in access level.my problem is this, the router is not a cisco router, and this router is not able to make NAT on more than one subnet.Into the core switch I've created 4 VLAN and I must to give internet access to 3 of them, 192.168.0.0/24 (vlan1), 172.16.0.0/24 (vlan2), 172.17.0.0/24 (vlan3).I've connected the switch to router via gigabit ethernet 0/1 and I've assigned to this interface ip address 192.168.10.2, the router ip address is 192.168.10.1, Switch ip default-gateway is router ip address 192.168.10.1, ip default route is 0.0.0.0 0.0.0.0 192.168.10.1 I've enabled ip routing feature and I've set no switchport feature to interface gigabit ethernet 0/1.From core switch I can ping router ip address but I can't make it from all other user, and the users not able to have internet access.
Below the switch configuration (only necessary strings)
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code].....
View 6 Replies
View Related
Sep 5, 2012
My understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies
View Related
Oct 16, 2012
is it possible to run a Catalyst 4500 as pure Layer 2 Switch, i.e. disabling "ip routing", but still managing the switch via Fa1, i.e. the defautl mgmtVrf vrf ?I tried the following:
!
no ip routing
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address 192.168.1.1 255.255.255.0
!
ip route vrf mgmtVrf 0.0.0.0 0.0.0.0 192.168.1.254
ip default-gateway 192.168.1.254
I was not able to reach the Switch even from the same subnet. Only after enabling ip routing I could manage the Switch. I haven't found any command to set ip default-gateway for a vrf. Any workaround to keep routing disabled, but still manageable via VRF?
View 3 Replies
View Related
Apr 12, 2013
Configuring OSPF on a catalyst 3560G Switch to connect to our building next door by way of fiber. The other two switches in the other building are running OSPF, I am trying to connect to the other building and access a server which is on a switch running OSPF. I am trying to configure the switch here to run OSPF and be able to see the neighbor, but currently can't although I've identified the networks. Maybe I'm missing something, I've followed the instructions but something is not right.
View 15 Replies
View Related
Dec 23, 2012
I just received a Catalyst 2960-C (WS-C2960C-8TC-L R) switch and I am unable to sign into its web GUI in order to configure it. I've tried both the Cisco Network Assistant and Internet Explorer and I am unable to log in either way. The documentation provided by Cisco states that the default password is simply cisco and that a username is unnecessary. Needless to say, it doesn't work. I've also Googled for other default passwords (such as cisco-cisco as the username-password), none of which worked either. I've also tried resetting the switch back to its factory default a few times.
View 8 Replies
View Related
May 23, 2012
I'm building the below network configuration:
WAN -------- ASA5505 ------<802.1q trunk>----- L3 switch -----<802.1q trunk>----- L2 switch w/ VLAN support
The following VLANs exist on the ASA and both switches: VLAN 10 (10.10.10.0/24), VLAN 11 (10.10.11.0/24), and VLAN 99 (10.10.99.0/24).
The ASA5505 performs the following functions: routing to/from the WAN, firewall, NAT, and DHCP for each VLAN. It has an interface on each VLAN (10.10.x.2) for a DHCP server.
The L3 switch provides inter-VLAN routing and layer 2 switching. The L2 switch provides layer 2 switching, with VLAN support.
What should the default gateway on the L3 switch be? Should I set the IP of the physical interface connected the L3 switch to the ASA5505.
View 8 Replies
View Related
Jan 9, 2012
I would like to know if ip helper-address feature is working on a layer 2 switch (2950,2960) or you should use a Layer 3 switch to do that?
View 7 Replies
View Related
Jul 30, 2012
Configured Layer 3 portchannel from 6500VSS enabled switch to two different 6500 standalone switch. Configured first ip on VSS switch, second ip on standalone switch1 and third IP on standalone switch2. My question is
1. Will the portchannel be up?
2. If port channel is up, will I able to ping the connected IP's.
View 1 Replies
View Related
May 16, 2013
We are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing. They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too.
View 3 Replies
View Related
Dec 3, 2011
I need a L2 switch with dual AC power supply and RJ45 uplink The optin I got was WS-C3560X-48T-L + C3KX-PWR-350WAC , but the problem is with uplink . There is no RJ45 1G uplink , there is only option for SFP uplink The another option was WS-C2960G-48TC-L , but there is no dual AC power supply option a good model ( Dual AC power supply , RJ 45 uplink ports (Gig) , with 48 port 100/1000 UTP)
View 3 Replies
View Related
Mar 18, 2009
Can a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies
View Related
Feb 14, 2013
can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies
View Related
Aug 14, 2012
4500 switch is connected to 2960 switch.
4500 config
Vlan 10
name Data
It has ip helper configured that points to DHCP.From 4500 switch port - port x connects to 2960 port.Port x is configured as trunk between 4500 and 2960.
2960 config
vlan 10
name data
All user ports are configured under vlan 10 and as access ports.Port x is trunk port connected frpm 2960 to 4500 switch allowing vlan 1 and 10 only.This switch has no default gateway configured.
We connected user PC on 2960 switchports and they were able to get the IP from DHCP server and were able to access the network? My question is how users on 2960 switch are able to access the network without ip default-gateway configured on 2960 switch?
View 6 Replies
View Related
Apr 1, 2012
Do you have the ability to setup DHCP servers on this layer 3 switch? I know I can with my old 3550 switch. Want to upgrade and make sure this model supports setting up dhcp servers on it.
View 3 Replies
View Related
Jan 15, 2013
My first question is I have an access layer switch which is a single VLAN and I am trunking that VLAN to a distribution layer switch, I can ping the gateway on the distribution layer switch for THAT VLAN, But cannot ping the gateway address for the second VLAN I have on the distribution layer switch. I know it is simple, But I have forgotten and just need a push
Also I have a third VLAN set to route traffic not bound for those 2 VLANs out to a router is the statement "ip route 0.0.0.0 0.0.0.0 172.16.252.2" good enough and do I actually need to create a VLAN for that traffic? and if so, is an access switchport the best option?
View 2 Replies
View Related
Jun 5, 2012
I have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes according to LAN QoS configured on interface
we have configured both the commands shape and share.
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?
View 5 Replies
View Related
Mar 18, 2012
I want to setup VLAN with the switches SG300 and SLM2024. What is the suggestion to connect these 2 switches. We have the Juniper net screen.
View 1 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Jun 4, 2013
I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
View 3 Replies
View Related
Feb 26, 2012
how to take the event log of Cisco switch 3560, its argent.
View 1 Replies
View Related
