Cisco Switching/Routing :: 3560 / Getting Layer 3 EtherChannel Configuration
May 23, 2012
I been practicing with the configuration of layer 3 etherchannel configuration and i am facing a problem here. I have two 3560 switches and i want a layr 3 ether channel configuration setup between the first 2 ports of bothe the switches. I assign IPs to the Port-channel 1 of both the switches "10.1.1.1 /24 and 10.1.1.2 /24" but i am unable to get a successful ping. what am i doing wrong. below are the configs for bothe of my switches.
3560_1
Building configuration...
Current configuration : 1274 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
[code].....
View 2 Replies
ADVERTISEMENT
May 23, 2012
i have made a topology in packet tracer related to etherchannel configuration.i am using 2 3560 switches and 1 2950 switch. Now what i want is to bundle up the redundant links between these 3 switches. The links fa0/1-3 between 2950_1 and 3560_1 switches have been bundled up but when i try to bundle the links fa0/4-6 of 3560_1 to fa0/4-6 of 3560_2 it wont work. i am using channel-group 1 mode desirable between the 3560 switches. secondly if i want to assign ip to port channels then it has to be of same subnet between 2 3560 switches right and it must be same between 2950_1 and 3560_1. But these 2 subnets should be different from one another.
View 3 Replies
View Related
Jun 10, 2013
Is it possible to to build a Layer 3 ether channel from two separate physical switches (layer3) that are trunked together?I know you can easily do this on a single switch and on stacked switches which I've done but in this case the customer have purchased two 3560X's which are not stackable yet want redundancy. The purpose of the etherchannel is to connect both switches to a private circuit provided by the hosted partner then route to the same setup in the DR location to different subnets.
View 4 Replies
View Related
Nov 23, 2011
As we know there are three layer in cisco Network Model:
-Core
-Distribution
-Access
So my question is in Core / Distribution layer should i use Etherchannel between switches or use Stacking if switches are stackble.For ex: suppose I have two cisco 3750 switches . so should i use etherchannel between them or use stacking in core layer?What are the advantages and disadv of both.
View 5 Replies
View Related
Dec 6, 2011
Is it possible to have ether-channel across 2 switches? As an example, having a server with 2 ports connect, 1 port to Switch-A and the other to Switch-B and then use those two links on the sepatate switches but to the same server to form an Etherchannel.
The Switch-A and Switch-B are 3560 series
View 2 Replies
View Related
Mar 3, 2012
I am using 3560.IP rouitng is being turned off on this.Curious to know if I will create etherchannel or port channel.I think etherchannel.Correct me if I am wrong.On connecting switches I have vlan10,20,30 to be allowed.I am sure I need to allow these all vlan in 10,20,30 which are on the trunk port on each side switch.Post that will add channel-port lacp and make it in active mode.Is that correct.This way traffic will be load-balanced/aggregated on minimum 2 ports who are the part of this.
View 2 Replies
View Related
Jun 20, 2012
I'm configuring two etherchannel groups (2 ports in each) on a 3560 switch. I need to trunk multiple vlans over each channel group.
I created the vlan trunks and allowed vlans on each physical interface. I notice that I can also configure the vlan trunks on the port-channel interfaces that were created. Should I configure them under those interfaces, or leave them on the physical interfaces? Relevant config is below:
interface Port-channel1
!
interface Port-channel2
[Code].....
View 1 Replies
View Related
Mar 17, 2013
I found that when I enabled layer 2 auto QoS in 3560 switch, I need to wait so much time to open a file in network drive. Howerver, when I disable the Qos. It can improve a lot. I have used a sniffer to capture the packet to see. Those default packet is in DSCP 0. Therefore, I think majority packet will drop to queue 4. How can I increase the buffer and threshold in order to improve queue 4 performance.
View 1 Replies
View Related
May 25, 2012
I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.
View 3 Replies
View Related
Nov 29, 2012
RACK 1 is the old rack and NEW RACK is the rack which is going to be procurred for some new Servers. All the Servers in the RACK 1 has a default gateway as PIX Inside IP. As of now the 3560 Switches acts as Layer 2 and does not have L3 IP routing enabled. How can I enable conenctivity between 192.168.36.0 range and 192.168.57.0 range wihtout making any change to current PIX inside IP address 192.168.57.1?Is it possible that I can enable IP routing on the 3560 Switches , create interface VLAN 36 and since already Switch 2 has it 's default gateway as 192.168.57.1 , Would the traffic from 192.168.36.0 be routed to 192.168.57.1 ? Or do I need to create static route for that ?Since L3 Routing is not enabled and since the 3560 Switches are just acting as L2 , the VLAN 2 - 192.168.57.0 range does not have any interface VLAN configured. When it is changed I would need to create interface VLAN 2 on 3560 Switches?
View 18 Replies
View Related
Apr 9, 2012
I am setting up a link between buildings that uses wireless links. I'm using Layer 3 routed ports on 2 3560 switches to handle the routing between sites. Normally I would just put these in a /30 and then the switches handle the rest. However, the wireless access points have a web interface for managing them that I want to be able to access, but it's only available on the single NIC that also carries traffic. What would be the best way of making this work? Should I make the link a /29 and give the access points an IP in the same range? If this is the case what do I use for the default gateway for the access points?
I have included a diagram to try to explain the issue clearer. The IP addresses in black are what I would do if this were a standard cable (and indeed this will work, but I wont be able to access the admin interface of the wireless AP) and the red ip addresses are the alternative if I use a /29 (but as I said, I'm not sure what to use for the default gateways).
View 1 Replies
View Related
Feb 17, 2013
seeking for configuration assitance on etherchannel between catalyst 3750 and 6506
View 3 Replies
View Related
Dec 20, 2012
I have stack of 2 switches 3750?I config etherchannel between them.
here is result
2 Po2(SD) LACP Fa1/0/15(I) Fa2/0/15(I)
Both ports are up up but standalone Int port channel 2 is down down.Need to know if this is default behaviour when we config etherchannel between stack switches?
View 2 Replies
View Related
Oct 24, 2012
I am installing a several new Cisco VM servers. The VM hosts are losing connectivity when we apply the etherchannel config in the core stack. VMware has stated that the etherchannel load balance needs to be src-dst-ip in order for the etherchannel to work.However, my current stack has 2 etherchannels configured to other switches through out the bldg in network closets. The current load balance configuration is src-mac.My question....when I make the change to src-dst-ip, will my network connectivity go down? I saw there was an older article on this that doesnt provide an answer just a work around. Here is the article. [URL].
View 1 Replies
View Related
Apr 29, 2013
I've turned up a new layer 2 WAN link between two data centres and i'm having some trouble trying to logically figure out how things should be configured.As you can see from the diagram i've created, I have the link connected on port 13 on one switch and port 14 on the other. Both ports have an IP address assigned to them and they can both ping each other..
The problem comes when I need to add routes in order to get traffic flowing over the link.I added an IP address to switch 2 on the link interface (port 14) as: 192.168.4.10
I then added an IP address to switch 1 on the link interface (port 13) as:
192.168.1.10
192.168.2.10
When I tried to add 192.168.3.10, it said "192.168.3.0 overlaps with VLAN2626". This would be correct as Vlan 2626 has an IP address of 192.168.3.15.
However, if I remove the IP address from vlan 2626 and add 192.168.3.10 to vlan 2 (the link port VLAN), I would surely lose remote access to the switch. (I'm telnetting into the switch from a machine on vlan 2626).
I started to tinker with this by manually adding a route to a server in each location and seeing if I could get traffic to flow:
On server 1: route add 192.168.4.0 MASK 255.255.255.0 192.168.1.10 METRIC 1
On server 2: route add 192.168.1.0 MASK 255.255.255.0 192.168.4.10 METRIC 1
If I try to tracert 192.168.1.20 from server 2, the first hop is the default gateway instead of 192.168.4.10.
The ultimate goal is to add the static routes to the Layer 3 router/firewall, but before I do that, I need to be sure of what to add to that router (It's a manged firewall from the data centre, so I don't have access to it and I need to raise firewall change requests to get the work done, so want to ensure it's right first time.
View 9 Replies
View Related
Sep 15, 2012
I have 2 locations, at a distance of 600KM.These two locations are well connected by Point to Point L2 VLAN with a speed of 2 MBPS and supported by CISCO 3560G switches.Location A has a VLAN to communicate to the other VLAN at Location B. Location B has also got 3 VLANS which are inter connected with Location A.Now the hardware in one of VLANs in Location B has moved to Location A for obvious reasons.
For further refernce am giving the VLAN IP address here....
Location A
VLAN1 for communicatng to Location B
IP Range 172.20.44.210
Subnet Mask 255.255.255.0
Default Gateway 172.20.44.210
VLAN2 for the desktops in Location A
IP Range 192.193.194.1-255
Subnet Mask 255.255.255.0
Default Gateway 192.193.194.1
[code]....
View 3 Replies
View Related
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Aug 27, 2012
A client of ours has installed an SG300-24P switch and would like to setup a LAG between the SG300 and the 3560 switch we manage for them. They would like the LAG to also pass the voice and two data VLANs currently in use; 5, 10, and 100 respectively. I configured the two ports as an Etherchannel with trunking on the logical port, but no luck. I reconfigured as follows:
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
end
[code]....
I see no output when I do show lacp nei. At this point the client is looking to use for the configurations to use as he does not know how to setup the SG300 and it is a switch I have never dealt with. I have found some configurations that I believe would allow a single VLAN across, but nothing I believe will allow the LAG to pass all the VLAN's.
View 7 Replies
View Related
Jun 2, 2013
How many secondary network config possible???
Switch - Cat3560
IOS Ver 12.2(50)se5
View 6 Replies
View Related
Jan 15, 2013
My first question is I have an access layer switch which is a single VLAN and I am trunking that VLAN to a distribution layer switch, I can ping the gateway on the distribution layer switch for THAT VLAN, But cannot ping the gateway address for the second VLAN I have on the distribution layer switch. I know it is simple, But I have forgotten and just need a push
Also I have a third VLAN set to route traffic not bound for those 2 VLANs out to a router is the statement "ip route 0.0.0.0 0.0.0.0 172.16.252.2" good enough and do I actually need to create a VLAN for that traffic? and if so, is an access switchport the best option?
View 2 Replies
View Related
Mar 18, 2012
I want to setup VLAN with the switches SG300 and SLM2024. What is the suggestion to connect these 2 switches. We have the Juniper net screen.
View 1 Replies
View Related
May 5, 2012
I have a network with static routes witch I need to convert to OSPF.Never used OSPF, and do not have much experience in routing in general.The netvork is connected via some fiber links, but moastly wireless bridges.I have attached a drawing of how the network is.Routers are 3550, 3560 and 3750s.Each router is on a different physical site.
View 2 Replies
View Related
May 26, 2013
how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies
View Related
Apr 15, 2012
I have two MLS conected by 2 fast ethernet links f0/11 and f0/12 on both sides.I am trying to set up a layer 3 etherchannel using these two links . But when i see etherchannel summary, they dont show up as layer 3. Instead they show as layer 2.
View 19 Replies
View Related
Sep 8, 2012
I need to build a layer 2 etherchannel on a Cisco 3560X. Now the question:
¿ May I instruct the switch to inspect the outgoing ethernet packets for IP information and therefore execute Layer 3 load balancing on this portchannel regardless of the fact that this will be a plain Layer 2 etherchannel? (for example: port-channel load-balance src-dst-ip)
The documentation does not say that this is not allowed, so in principle it seems to be that it would be feasible.
View 1 Replies
View Related
Jan 25, 2012
I am trying to see how can configure MQC in Etherchannel. I know that i need to do this in the memeber physical interfaces of the etherchannel.The etherchannel is a trunk port allowing few VLANs. SVIs are created in the switch for this VLANs as well. tell me where i need to apply the QOS ? Is it under the member physical interfaces ?.
What will happen if QOS applied under the SVIs?
View 5 Replies
View Related
Apr 22, 2011
can i use normal two L3 Switch(3560) for BGP Multihoming with 2 different isp
View 4 Replies
View Related
Jul 6, 2011
I have the following scenario. Connected to a Cisco 3560 switch (fa0/9) is another Cisco switch (that is operating at layer 2). On the other side of that second switch is a firewall. I want to send traffic from my Cisco 3560 switch to a network behind the firewall. [code] However, when I try to add the ip address to int fa0/9, I get an error. Right now, the 3560 is operating at layer 2. I think that I need to issue the command: "ip routing" to put it in layer 3, then put the ip address on port fa0/9. However, I am concerned that I will mess up my production environment. Is there any other way of doing this? The "ip route 0.0.0.0 0.0.0.0" statement sends traffic out the gateway to the Internet. I just want to send packets to 209.52.62.16/28 out int fa0/9.
View 2 Replies
View Related
May 4, 2011
I recently was asked to turn a routed link between our HQ and our DR Site into a trunked link to allow us to span our main Server VLAN up to the DR Site.I was informed by the ISP that owns the 100Mb Leased Line between the sites that the link was configured to pass dot1q traffic and I should just have to configure my links at either end as trunks to get the link to come up.
There is a Cisco 3560 at either end with Layer 3 routing enabled (obviously as this was a routed link previously).So, I scheduled an outage and configured either end as a trunk links as follows and repointed any routes from the /30 routed addresses to the management addresses of the switches on either side:
***For info VLAN 15 is the DR Site and VLAN 11 is the Server range at our HQ and was available on the connected switch***
interface FastEthernet0/24
switchport trunk encapsulation dot1q
switchport trunk native vlan 15
switchport trunk allowed vlan 11,15
switchport mode trunk
[code].....
View 6 Replies
View Related
Jun 9, 2013
When I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T8,
sfo-c3845-1#sho run int port-channel 1
Building configuration...
Current configuration : 31 bytes
!
interface Port-channel1
end
[code].....
View 3 Replies
View Related
Feb 3, 2013
I am trying to implement an etherchannel on a cisco 2901 (IOS 15.1). i have already created the port-channel but i cannot assign the gig interface to the channel group.
View 1 Replies
View Related
Jun 11, 2012
I have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies
View Related
Mar 25, 2013
I have two switches 6509 one switch is confire with VTP domain ABC Other switch is configure with ABZ, At present the switch is configure with the L3 interface and one fiber cable is connected between two switches.I want to remove L3 configuration wants to make L2 etherchannel and wants to ceraeate Loop back will assing same ip both side.The OSPF is configure both side , i will not do any changes in the OSPF as L3 ip is advertise in OSPF.
View 1 Replies
View Related
