Cisco Switching/Routing :: 3560 - Secondary Network Configuration
Jun 2, 2013How many secondary network config possible???
Switch - Cat3560
IOS Ver 12.2(50)se5
ADVERTISEMENT
Cisco Switching/Routing :: Routing Secondary Network On 3560 Switch
Jun 4, 2013I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
Cisco Switching/Routing :: Insert Secondary Power Supply To 3560?
May 22, 2013while the 3560 switch is running? Is it hot-pluggable?
WS-C3560X-48P is the switch and I would be adding a C3KX-PWR-1100WAC
Cisco Switching/Routing :: Getting The Vlan Configuration / 3560?
Sep 15, 2012I have 2 locations, at a distance of 600KM.These two locations are well connected by Point to Point L2 VLAN with a speed of 2 MBPS and supported by CISCO 3560G switches.Location A has a VLAN to communicate to the other VLAN at Location B. Location B has also got 3 VLANS which are inter connected with Location A.Now the hardware in one of VLANs in Location B has moved to Location A for obvious reasons.
For further refernce am giving the VLAN IP address here....
Location A
VLAN1 for communicatng to Location B
IP Range 172.20.44.210
Subnet Mask 255.255.255.0
Default Gateway 172.20.44.210
VLAN2 for the desktops in Location A
IP Range 192.193.194.1-255
Subnet Mask 255.255.255.0
Default Gateway 192.193.194.1
[code]....
Cisco Switching/Routing :: 3560 - Switch With 1 VLAN Configuration?
Mar 18, 2013I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
Cisco Switching/Routing :: 3560 / Getting Layer 3 EtherChannel Configuration
May 23, 2012 I been practicing with the configuration of layer 3 etherchannel configuration and i am facing a problem here. I have two 3560 switches and i want a layr 3 ether channel configuration setup between the first 2 ports of bothe the switches. I assign IPs to the Port-channel 1 of both the switches "10.1.1.1 /24 and 10.1.1.2 /24" but i am unable to get a successful ping. what am i doing wrong. below are the configs for bothe of my switches.
3560_1
Building configuration...
Current configuration : 1274 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
[code].....
Cisco Switching/Routing :: LAG / Trunk Configuration Between 3560 And SG300-24P
Aug 27, 2012A client of ours has installed an SG300-24P switch and would like to setup a LAG between the SG300 and the 3560 switch we manage for them. They would like the LAG to also pass the voice and two data VLANs currently in use; 5, 10, and 100 respectively. I configured the two ports as an Etherchannel with trunking on the logical port, but no luck. I reconfigured as follows:
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
end
[code]....
I see no output when I do show lacp nei. At this point the client is looking to use for the configurations to use as he does not know how to setup the SG300 and it is a switch I have never dealt with. I have found some configurations that I believe would allow a single VLAN across, but nothing I believe will allow the LAG to pass all the VLAN's.
Cisco Switching/Routing :: 3550 / 3560 / 3750s - OSPF Configuration For The First Time?
May 5, 2012I have a network with static routes witch I need to convert to OSPF.Never used OSPF, and do not have much experience in routing in general.The netvork is connected via some fiber links, but moastly wireless bridges.I have attached a drawing of how the network is.Routers are 3550, 3560 and 3750s.Each router is on a different physical site.
View 2 Replies View RelatedCisco Switching/Routing :: Reset Password And Retrieve Configuration On Switch 2950 And 3560?
May 26, 2013how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies View RelatedCisco Switching/Routing :: 3560 Topology In Packet Tracer Related To Etherchannel Configuration
May 23, 2012i have made a topology in packet tracer related to etherchannel configuration.i am using 2 3560 switches and 1 2950 switch. Now what i want is to bundle up the redundant links between these 3 switches. The links fa0/1-3 between 2950_1 and 3560_1 switches have been bundled up but when i try to bundle the links fa0/4-6 of 3560_1 to fa0/4-6 of 3560_2 it wont work. i am using channel-group 1 mode desirable between the 3560 switches. secondly if i want to assign ip to port channels then it has to be of same subnet between 2 3560 switches right and it must be same between 2950_1 and 3560_1. But these 2 subnets should be different from one another.
View 3 Replies View RelatedCisco Switching/Routing :: How To Create Network 3560
Sep 11, 2012creating an Access List on my Intervlan network.how I create my network.I've managed to get the Inter-vlan working and my problem now is to restrict some vlan from accessing one another.
- I've enabled IP Routing on 3560 switch.
- All vlans can PING each other.
- All vlans can access the internet (172.16.1.2)
Cisco Switching/Routing :: 3560 IOS Upgrade On Production Network
Nov 21, 2012Looking for input/thoughts on the upgrade of our 3560's and 3750's while on production network.
While we could remotely send the IOS over the network to the device, I'm concerned about errors and the lack of physical control of the device. So, the thought is to just go to the comm closet, plug in with laptop to the console port, and upgrade the IOS over the console port. But this would require xmodem, correct? I know the fastest way would be to a. configure an empty fa0/0 port to no switchport, add an IP address, and use tftp. BUT, we would have to isolate the switch from the production network while connected to it with our laptop. Otherwise, our laptop would be seen on the network as an unknown device, and there would be repercussions...
So, we console into the device, and u/l the IOS that way. Is there a way to increase the baud rate on the switch to 115200, change putty to 115200, then do the x modem? I just say we should shut all the ports to isolate the switch from the network, then tftp the IOS to the switch. Unplug, reopen the ports, then reboot the switch.
Cisco Switching/Routing :: 3560 / ISR 2911 - NAT Of Network That Is Not Directly Connected
Dec 1, 2011I have a CAT 3560 connected to a ISR 2911 The 3560 has 2 subnets ( 192.168.1.0 /24 and 10.10.10.0 /24) The 2911 has interface GigabitEthernet0/1 on the 192.168.1.0 /24 and another GigabitEthernet0/0 on a WAN connection 172.16.7.246 I need to NAT both the 192.168.1.0 /24 and the 10.10.10.0 /24 to the single address 172.16.7.246 I have to use route-maps . I have IPSec VPN's and ZBF on the 2911 My problem is the NAT does not work for the 10.10.10.0 /24 network!Why?is my only option to use trunking between the 3560 and 2911 and subinterfaces on the 2911? I want to avoid sub-interfacing.
=============================================================
On the Cat 3560=====================!vlan 40name the 192.168.1.0 /24 subnet!vlan 60name the 10.10.10.0 /24 subnet!interface FastEthernet0/7description Connection to Router Gig0/1switchport access vlan 40!interface FastEthernet0/16description Connection pc host on the 10.10.10.0 /24 subnetswitchport access vlan 60!interface Vlan1no ip address!interface Vlan40ip address 192.168.1.4 255.255.255.0!interface Vlan60ip address 10.10.10.10 255.255.255.0!ip classlessip route 0.0.0.0 0.0.0.0 192.168.1.1
=========================
The host on the 10.10.10.0 /24 network has the 10.10.10.10 address as it's default gateway The host can not access the WAN thru NAT....
Cisco Switching/Routing :: 3560 - Monitor Bandwidth Utilized By Servers In Network
Feb 6, 2013I have 5 linux and 3 Microsoft 2008 Servers, each connected to 2 Cisco 3560 Switches. The 2 Cisco 3560 switches are connected to 2 different Cisco 515e Pix. Is it possible that if i enable Port SPAN in any of the switchport and send a copy of traffic to any of the windows 2008 server, will i be able to monitor the bandwidth of the servers (Here I am only looking for traffic going from servers to PIX and then to internet, also vice versa).
Also will wireshark be able to differentiate specify the bandwidth of each servers seperately ?
Cisco Switching/Routing :: 3560 - Upgrade To Make Voip Network And Wireless?
Jan 21, 2013i have 300 user in network in 2 building and firist buiding 5 flors.i use subnet /22.i have core switch 3500xl fiber and 8 swith 3560 and my network have 2 router one for adsl and other for mpls so i want upgrade it to make voip network and wireless
so if i need replace switch what i model and how many?
Cisco Switching/Routing :: 4500 / 3560 / 2950 - Slow Network / Broadcast
Jan 31, 2012Our network feels slow and trying to find the best way to investigate this properly. We have Cisco chassis 4500 with mix of 3560/2950 Edge switches 1GB backbones and WLC/WCS in place. The network is broken into multiple V LANS and IOS on our switches haven't been updated in 3-4 years.
On a wireless laptop (G) with get throughput of 1-2MB/s transfer speed with usually 10 clients per AP and LAN we get anywhere between 7-15 MB/s transfer. Using wire shark on a wireless laptop we see a lot broadcast traffic from other clients and the same for LAN. What is the best way to troubleshoot performance issues on the network and where do I start?
Cisco Switching/Routing :: 891 Router Secondary Ip Route
May 22, 2013I have an MPLS network router(Router1) and an internet router(Internet1) at a site of mine(Site1). the MPLS router sends all unknown traffic out the internet router. Router1 is the default gateway for all hosts and directs the traffic.I also have another network at an alternate site (Site2) on the same mpls network also with an internet egress. It is composed of an MPLS router (router2) and an internet router (Internet2).I would like Router1 to send internet bound traffic out Internet2 if Internet1 is down. Basically the statement on Router1 for the unknown traffice is ip route 0.0.0.0 0.0.0.0 172.31.1.254I have never heard of IP SLA before but it seems to be the best method for this situation.
View 2 Replies View RelatedCisco Switching/Routing :: 6509 Secondary SUP Has Failed
Apr 15, 2012I have 6509 with dual sups, the secondary sup has failed and I am not able to bring it up even after reboot. the state says unknown/other. What that state" unknown" means?. I could not find any documentation about this state. [code]
View 5 Replies View RelatedCisco Switching/Routing :: HSRP On Secondary IP Address - 2900
Feb 21, 2013I have a few old 2600 routers (2621, different IOS's) which I'm now replacing for new one's from the 2900 series (2901, Version 15.1(4)M4).In my configuration I have two IP addresses in my LAN interface and I have HSRP configured within the secondary IP subnet range. It would be something like this:
interface GigabitEthernet0/1
ip address 172.x.x.x x.x.x.x secondary
ip address 10.z.z.z z.z.z.z
[Code].....
Now, in the new 2900 routers, my interface configuration hasn't changed however I can see that the hello packets are now sent with the source within the respective HSRP IP subnet so I had to edit my acl for that:
permit udp 172.x.x.x x.x.x.x host 224.0.0.2 eq 1985
Is there a way I can force the HSRP to work as it previously did in the old IOS's?
Cisco Switching/Routing :: 2801 Secondary IP / Port Forwarding?
Mar 26, 2012I have the above firewall which is working as it should but I have came across an issue with a recent upgrade to Microsoft Exchange 2007 and Outlook 2010 Autodiscovery due to the way the port forwarding has been configured for Outlook Web Access (OWA) on the router.
The router is forwarding OWA requests to the exchange server on port 8080 and the default website in IIS on the Exchange Server under which OWA sits and unfortunately Autodiscovery has been set with an SSL port of 8080. I think the reason for this is that we have an RDP server and the router is forwarding all port 443 requests to this server. Due to this Outlook clients cannot connect to Exchange through autodiscovery and cannot therefore get FREE/BUSY and a few other things.
I have 5 public IP addresses and only use two at the moment, one on the ADSL router and one on this firewall. I have no spare interfaces on either the router or the ADSL router.
My question is, is it possible to have a secondary ip address set on the public facing interface and set different rules for this IP which would allow me to forward requests on that IP to a different server?
Cisco IOS Software, 2801 Software (C2801-ADVSECURITYK9-M), Version 12.4(16b), RELEASE SOFTWARE (fc3)
Building configuration...
Current configuration : 4778 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
Cisco Switching/Routing :: Boot 4503-E Switch From Secondary Image?
Sep 13, 2011We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies View RelatedCisco Switching/Routing :: Catalyst 3750X With PoE Secondary Power Supply Options?
Jul 21, 2012 When quoting a Catalyst 3750X with PoE (WS-C3750X-48P-E) the Dynamic Configurator Tool allows to include as the secondary power supply option the Catalyst 3K-X 350W AC Secondary Power Supply (C3KX-PWR-350WAC/2), but the default included primary power supply is the Catalyst 3K-X 715W AC Power Supply (C3KX-PWR-715WAC). My questions are the following:
1. Will this combination of power supply work?
2. Will the C3KX-PWR-350WAC/2 be able to power up the switch if the primary power supply of 715W fails?
3. Will the PoE will be lost if the primary power supply fails and only the secondary power supply of 350W keeps working?
4. If this secondary power supply of 350W is not suitable for PoE, why it is available as a secondary power supply option in the Dynamic Configurator Tool for a PoE switch?
Cisco Switching/Routing :: C6509 - Broadcast Not Working Between Primary And Secondary IP Address
May 11, 2012I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine... Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...
View 6 Replies View RelatedCisco Switching/Routing :: 6500 Shutdown Interface On One Router / Deleted Secondary Address
Jul 15, 2012I have just updated a VLAN interface on my router. I have two 6500's with GLBP configured. The particular interface had a primary and secondary IP address. I shutdown the interface on one router and deleted the secondary address then assigned the orignal secondary address to be the be the only address associated with the interface and enabled the interface and it came right back up...all looks good. I proceeded to do the same thing to the other router and once again all looked good. Now, I am able to PING the devices in the subnet from router, but am unable to ping them from any place else. [code]
View 2 Replies View RelatedCisco Switching/Routing :: 887m - Unable To Route Data Between Primary And Secondary IP Networks
Jan 7, 2013We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
Cisco AAA/Identity/Nac :: ACS 5.2 - Primary-secondary Radius Server Configuration
Apr 21, 2013I have a couple of ACS 5.2 configured as active and backup and I am doing dot 1x authentication using these servers . I have configured the switch with the bellow configuration.
radius-server host 10.0.10.15 auth-port 1645 acct-port 1646
radius-server host 10.0.10.16 auth-port 1645 acct-port 1646
radius-server key 7 aaaaaaaaaaaaaa
please help to understand what will happen in switch
1) in case of primary failure
2)in case if primary returns alive .
Cisco Switching/Routing :: 1721 / Change Remote Site Network Configuration With / Without Losing Connection?
Sep 19, 2012My company just assumed management of a remote entity. The network has several misconfigurations and I need to make some network modifications from my office w/o losing access or incurring lengthy outage to the clients. The network consists of 1721 router and three 2960 switches.
- I only have access to the router from the Internet. I telnet off the router to the 3 switches.
The site uses a single class C 192.168.1.0 / 24. The router is running RIPv2 even though this is the only network. The prior network person (contractor) set up separate native vlans on each switch and all the ports are defined as Native trunk and access are defined to the VLAN interface assigned to the switch. So of course the logs are flooded with Native VLAN mismatch, Each 2960 switch is a VTP server but has no VTP domain.
basic network layout:
Internet => Eth [Cisco 1721] => Fa 0 192.168.1.254 ==> [SW1]
[SW1]
interface Vlan1
no ip address
no ip route-cache!interface Vlan220ip address 192.168.1.219 255.255.255.0no ip route-cache
[code]....
!interface GigabitEthernet0/1description SW2 Gi0/1switchport access vlan 204switchport trunk native vlan 204!interface GigabitEthernet0/2switchport access vlan 204switchport trunk native vlan 204!interface Vlan1no ip addressno ip route-cache!interface Vlan204ip address 192.168.1.224 255.255.255.0no ip route-cache Normally, I would assign the current 192.168.1.254 to a subinterface to Router Fe 0/0 but with each switch having its own native VLAN I am afraid I will lose connectivity to the downstream switches -- my only access is telnet off the Cisco1721 Router.
Cisco Switching/Routing :: 3560 Policy Based Routing Verify-availability
Apr 19, 2012Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop" do not do the same job.
View 8 Replies View RelatedCisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch
Dec 8, 2011The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
Cisco Switching/Routing :: 3560 VLAN Routing Between Switch And Router
May 8, 2012I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
Cisco Switching/Routing :: Make Policy Based Routing On 3560?
Apr 17, 2012I have tried to make policy based routing on Cisco 3560. I use ipservices ios (SW version 12.2.(50)SE3 and SW-IMAGE C3560-IPSERVICESK9-M) For below configuration there is no problem and pbr is working.
“Access-list 100 permit ip host 1.1.1.1 host 2.2.2.2
Access-list 101 permit ip host 1.1.1.1 host 3.3.3.3
Route-map pbr1 permit 10
Match ip address 100
Set ip next-hop verify-availability 1.1.1.2 1 track 11
interface fasthethernet 0/1
ip policy route-map pbr1”
But when i add another sequence to the "pbr1" with another sequence number like that.
“Route-map pbr1 permit 11
Match ip address 101
Set ip next-hop verify-availability 1.1.1.3 1 track 12”
pbr is not working. Switch gives message "PLATFORM_PBR-3-UNSUPPORTTED_RMP:Route-map pbr1 not supported for Policy Based Routing”"ip policy route-map pbr1" command not shown in the running config. And "show ip policy" output is blank.Configuration guide says you have insert many sequence to the route-map with the same name. And also this command is not in the unsupported command list.
Cisco Switching/Routing :: 3560 - Access List On InterVLan Routing
Dec 11, 2012I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
Cisco Switching/Routing :: 3560 - Unable To Perform VLAN Routing
Apr 28, 2012We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies View Related