Cisco Switching/Routing :: 3560 - Unable To Perform VLAN Routing
Apr 28, 2012
We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies
ADVERTISEMENT
Jan 21, 2013
Platform:
cisco6509-E with FWSM
Supervisor Engine 32 PISA 8GE
sup-bootdisk:s32p3-adventerprisek9_wan-mz.122-18.ZY2.bin
command:
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
(config)#no ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
#clear ip nat tran *
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
%Port 14029 is being used by system
Or %Static entry in use, cannot change
But when I perform "sh ip nat tran" command,There is nothing
View 1 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Jan 10, 2012
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies
View Related
Dec 5, 2011
Is there any way to check if this VLAN is used by somedevice?
Cisco3560#sh ip int b
Vlan55 unassigned YES NVRAM administratively down down
Cisco3560#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
55 Print active Fa0/5, Fa0/6, Fa0/7, Fa0/8
View 18 Replies
View Related
Jul 22, 2012
I have 4 vlan and all has conectivity/access with all (VLAN10,VLAN20,VLAN30 and VLAN40, I use a 3560 Switch for this propose, I need to modificate one vlan (VLAN40) that has access to the rest of the VLAN's BUT the rest of the VLAN's dont have access to VLAN40. I know that it is a problem of access-list BUT I can't undertand how to obtain the result that I like
View 1 Replies
View Related
Sep 15, 2012
I have 2 locations, at a distance of 600KM.These two locations are well connected by Point to Point L2 VLAN with a speed of 2 MBPS and supported by CISCO 3560G switches.Location A has a VLAN to communicate to the other VLAN at Location B. Location B has also got 3 VLANS which are inter connected with Location A.Now the hardware in one of VLANs in Location B has moved to Location A for obvious reasons.
For further refernce am giving the VLAN IP address here....
Location A
VLAN1 for communicatng to Location B
IP Range 172.20.44.210
Subnet Mask 255.255.255.0
Default Gateway 172.20.44.210
VLAN2 for the desktops in Location A
IP Range 192.193.194.1-255
Subnet Mask 255.255.255.0
Default Gateway 192.193.194.1
[code]....
View 3 Replies
View Related
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Jan 16, 2013
Topology: 3560 <-access-mode-link-> ASA5510 - Internet,3560 has 3 VLANs and 3 corresponding SVIs (default-gateways for VLANs),Just configured RAS VPN on ASA5510 and successfully made connection,Now, from RAS VPN (IPSEC) client workstation CLI, can ping all 3560 SVIs,CANNOT PING host devices plugged into switchports.
View 1 Replies
View Related
Dec 27, 2011
In my lab setup i configured Cisco 3560 switch.
-VLAN 20 and VLAN 30 i configured.
-VLAN 20 interface IP : 192.168.20.1/24
-VLAN 30 interface IP : 192.168.30.1/24.
Inter-vlan communication is happening fine. For testing for purpose i configured extended ACLs.i want stop communication from VLAN 30 to VLAN 20 but not vice-versa. If i ping from one of the IP VLAN 20 to one of the ip of VLAN 30, i was gettng Requested time out. And if i ping from one of the IP VLAN 20 to VLAN 30 interface IP, i was able get pinging.From VLAN 30 to VLAN 20, i was getting destination host unreachable from VLAN 30 ip( Its fine as its my requirement)So, solution needed to communicate from VLAN 20 to VLAN 30.
View 1 Replies
View Related
Apr 18, 2012
I have a 3560 switch with the following ports config [code] I would like to use theses ports on a different vlan to connect 4 pc's to them. Can I just remove them from the vlan, remove the trunk switchport and set up on the vlan i want them on with no trunking?
View 5 Replies
View Related
Apr 19, 2012
Probably an easy fix but something's weird in my config. I am setting up a new network, so this is not production, Routed environment, down to the access layer using 3560-x l3 switches.
vlan 10: data
vlan 20: wifi
vlan 30: wifi guests
vlan 40: voip
My objective is to allow all traffic OUTBOUND to certain subnets (10.10.0.0/24, 10.10.100.0/24, 10.10.110.0/24 10.10.120.0/24) and block any other 10.0.0.0/8 networks. By doing it this way, after blocking all other internal traffic, I allow everything else to ensure internet traffic can go out.
Extended IP access list VLAN10_TRAFFIC_FLOW 10 permit ip any 10.10.0.0 0.0.0.255 20 permit ip any 10.10.100.0 0.0.0.255 30 permit ip any 10.10.110.0 0.0.0.255 40 permit ip any 10.10.120.0 0.0.0.255 50 deny ip any 10.0.0.0 0.255.255.255 (5 matches) 60 deny ip any 172.16.0.0 0.0.255.255 70 permit ip any any!interface Vlan10description DATAip address 10.104.10.1 255.255.255.0ip access-group VLAN10_TRAFFIC_FLOW outendThe problem is, from the above info, when I ping 10.10.0.5 from a workstation in VLAN 10, it should match rule 10, but instead if matches rule 50 (as shown by the 5 matches)
View 13 Replies
View Related
Aug 6, 2012
When did this wonderful feature get introduced? Is it going to moved down to the 3560s/2960s type switches?
View 0 Replies
View Related
May 21, 2013
I faced the ( receive discard vlan 20 of Cisco switch 3560 ) on my Solarwinds Server .
View 1 Replies
View Related
Apr 17, 2012
We have over 30 Cisco 3560 switches and over 10 VLANs on our network. In our example, VLAN 10 on switch IP 10.0.20.150 works fine and VLAN 10 on switch IP 10.0.20.24 doesn’t work. The below are both switches show vlan. url....I can’t tell what causes the problem and how to fix it. VLAN 10 on Switch 10.0.20 24 doesn’t work. [code]
View 8 Replies
View Related
Apr 22, 2013
I have enabled IP DHCP snooping on a 24 port 3560 switch (v small office) and let the database fill up, now I have added dynamic arp inspection on the single vlan and I amd getting these errors.
Apr 23 16:15:34: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/5, vlan 1.([5835.d9b0.b9d1/172.30.5.2/0000.0000.0000/172.30.5.3/16:15:33 BST Tue Apr 23 2013])
Apr 23 16:15:39: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:39 BST Tue Apr 23 2013])
Apr 23 16:15:40: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:40 BST Tue Apr 23 2013])
[Code] .....
View 2 Replies
View Related
Jun 20, 2012
I'm configuring two etherchannel groups (2 ports in each) on a 3560 switch. I need to trunk multiple vlans over each channel group.
I created the vlan trunks and allowed vlans on each physical interface. I notice that I can also configure the vlan trunks on the port-channel interfaces that were created. Should I configure them under those interfaces, or leave them on the physical interfaces? Relevant config is below:
interface Port-channel1
!
interface Port-channel2
[Code].....
View 1 Replies
View Related
Jun 3, 2012
We have two Cisco switches with one 3560 and one 3750 we have created a new Vlan 4 with IP 10.1.3.x 255.255.255.0 - no shut then assigne to gi 2/0/46 on the 3560 Vlan 4 ip address 10.1.3.x 255.255.255.0 no shut then assign to FA0/45. All interfaces are up up along with the Vlan up up, we can ping the local IP address bu not able to pint the other switch.
View 2 Replies
View Related
Jan 12, 2010
I have a HP Procurve 5406 connected to a Cisco 3560 on a temporary cat5e connection and I have Mitel IP phones needing to go on the Cisco switch.Ive configured the HP Procurve port to TAGGING both VLAN 10 (data) and VLAN 20 (Voice). NO is selected for default VLAN 1.The Cisco is configured on the port with switchport encap dot1q and switchport mode trunk.
Ive configured an IP for interface VLAN 10 and i cannot ping it from across the network. The interfaces are up and happy. I have tried changing the VTP status from transparent to server (VTP pruning is off) ive tried setting allowed vlans 10,20. Still not a think. The worse thing is that i have a working Cisco switch with the HP procurve that i checked the config on and its the same! The only difference is that the media type is SX over SFP in that case.
p.s not that im at this stage yet but i initially configure the FastE ports as trunks with native vlans because i was using non-cisco phones. On a spare port i convigured the voice vlan 20 and i say on the mitel phone that it was looking on vlan20! I didnt expect that, i thought the Voice VLAN ID was carried on CDP enabled devices only.
View 9 Replies
View Related
May 20, 2010
For many years we've had the following vlan and port security config on our 3560s: [code] This has worked great on 12.2(37)SE1, 12.2(40)SE and 12.2(46)SE. However since 12.2(50)SE, and I've tried all the versions since then, we have a problem with 7900 phones and ATA186s taking upwards of 20 minutes before they can get a valid IP number.The problem on the newer IOSes seems to be related to the inactivity aging.On the older IOS versions the mac address of the voice device appears on the voice vlan straight away.
On the newer IOS versions the mac address of the voice device appears on the DATA vlan and seems to be stuck there until the inactivity aging removes it. It then gets re-learned, sometimes on the voice vlan, and sometimes on the data vlan. If you're unlucky and it gets re-learned on the data vlan you've got to wait until the inactivity time ages the address out again. Repeat until the mac address eventually gets learned on the voice vlan. I don't want to be stuck on 12.2(46)SE forever.
View 11 Replies
View Related
Nov 1, 2011
I've set up my 3560 to do routing. Now, I'm looking for a way to apply acl restrictions to the vlan interface ip address itself.
View 1 Replies
View Related
Jan 2, 2012
I need to implement the shaping VLAN only on the trunk link between the 6500 and 3560. [code]
View 8 Replies
View Related
Oct 11, 2010
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
View 8 Replies
View Related
Oct 25, 2012
I'm new to networking and was looking for some assistance. First off im using packet tracer to diagram my senario as I will be receiving my equipment next week to deploy.
Hardware to be used:
1. 2 catalyst 3560 switches
2. all connect to a sonic wall router
I have two companies that work in the same office space. I need to keep these companies seperate on their own vlan. They will however need to share the phone system.(Packet tracer file uploaded to give those who have the time to see what I put together.) [code]
View 13 Replies
View Related
Oct 30, 2011
I have configured a new switch 3560 switch and connected to 4500 switch and formed a trunk connectivity.Now the issue i am facing is when i do a SH CDP NEIGHBOUR from 3560 switch i am able so see 4500 swries switch but at the same time when i do SH CDP NEIGHBOUR form 4500 series switch i am not able to see the entry for 3560 switch.But i am able to telnet the new switch with out any issues
View 11 Replies
View Related
Feb 23, 2012
I have configured vlans in 3560G switch but vlans notable to accessing Internet
View 6 Replies
View Related
Mar 11, 2012
We have a 3750 and a 3560 defined as a layer 2 switches. One gig port on each switch is trunked to layer 3 switches, which containall the VLAN definitions etc. The other gig port on the 3650 and 3750 switches are trunked together to provide an alternative path in the event of a failure.
We have added a new device to the 3750 and given it a VLAN 9, and the VLAN added to allowable VLANS on both trunk ports between the layer 3 and layer 2 devices ie:
switch port trunk allowed vlan 9,10,20,30,40,50,60,90,200,202,206,211,212,700.
From either of the 3750 or the 3560 we can ping any device on any VLAN on any switch in this group with exception ofVLAN 9. We can however ping the ip address of VLAN 9 on the layer three switches.
View 2 Replies
View Related
Jan 2, 2013
I am slowly working my way though the setup and configuration of our new 4900m switch. The switch will have a pretty basic operational configuration. We are simply going to network 3 servers together through the swtich. Anyhow, I have been fallowing the guide at this site: [URL]
Basically the switch is brand new and I just setup things such as the clock, the banner, and the hostname. Anyhow, at various points in the guide such as the configuration of the telnet password and especially the interface gigabitethernet I get the "invalid input detected at '^' marker". I also did a show interfaces and noticed there was not any gigabitethernet interfaces but there was a
"FastEthernet1 is down, line protocol is down Hardware is Fast Ethernet for out of band management, address i"
Anyhow, my thinking is continuing on with the guide and at least try to setup the interface for the management port so I can then use the cisco network assistant gui to then configure the rest of the switch.
View 1 Replies
View Related
Apr 1, 2013
I am using a Cisco SG-300 28 port switch in layer 3 mode as my default gateway for all my devices. I have two vlans on the switch, vlan 1 and vlan 4. Both are pulling valid IP addresses in their scope from the DHCP server, and both have valid DNS settings. I set a static route to the Internet on the switch to our firewall (192.168.5.254). All devices connected to vlan 1 are able to access the Internet, however all devices connected to vlan 4 cannot get past the switch. A tracert from one of these devices shows it hits the switch as the gateway, but gets no further. [code]
View 4 Replies
View Related
Feb 4, 2012
i am stuck in a issue! unable to ping the SVI
i am design a small network for a office.
1 router 2811
1 switch 3750-e
Router is connected to the mpls cloud with ospf.
here re the config.
Router#
int fa0/0
ip 10.10.10.1 255.255.255.252
[Code]....
i connect my laptop and give ip 22.0.68.1 255.255.255.0 and default gateway 22.0.68.251but can not ping SVI VLAN 201 (22.0.68.251) ?
and from the SWITCH i can not ping the 20.20.20.2?
View 38 Replies
View Related
Feb 4, 2013
i configured the VLAN810, with DHCP services, while i try to ping the host which is connected to gi 1/0/2 from my gi 1/0/1 , i can't ping the same vlan host , while i try to debug ip icmp its showing ,
C3750XB11#sh running-config
Building configuration...
Current configuration : 12053 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
[code]....
View 5 Replies
View Related
Apr 6, 2012
I have a Nexus 5548 installed (layer 2 device only) with several 10G ports supporting IBM P770 systems and a TSM (Tivoli Storage Manager) system on a single VLAN. All of the Nexus 5548 ports are configured for jumbo frames. I was ask to install a new server on the same VLAN as the others but as 1G port without jumbo frames to allow communications with the TSM server. I'm assuming that the 1G port for this new server without jumbo frames configured on the Nexus 5548 will not be unable to communicate with the TSM server that is on the same VLAN with it's Nexus 5548 10G port configure using jumbo frames.
View 5 Replies
View Related
Jun 23, 2012
I am not able to create more than 256 VLAN in Cisco Nexus 5010 switch. While creating I am getting "No VLAN resources available for VLAN creation" Details below -
Switch model - 5010
Software : NX OS 4.0 (1a)
Error Message:
Nexus_5010(config)# vlan 417
ERROR: No VLAN resource available for VLAN creation.
View 5 Replies
View Related
