We have two Cisco switches with one 3560 and one 3750 we have created a new Vlan 4 with IP 10.1.3.x 255.255.255.0 - no shut then assigne to gi 2/0/46 on the 3560 Vlan 4 ip address 10.1.3.x 255.255.255.0 no shut then assign to FA0/45. All interfaces are up up along with the Vlan up up, we can ping the local IP address bu not able to pint the other switch.
View 2 RepliesI have a HP Procurve 5406 connected to a Cisco 3560 on a temporary cat5e connection and I have Mitel IP phones needing to go on the Cisco switch.Ive configured the HP Procurve port to TAGGING both VLAN 10 (data) and VLAN 20 (Voice). NO is selected for default VLAN 1.The Cisco is configured on the port with switchport encap dot1q and switchport mode trunk.
Ive configured an IP for interface VLAN 10 and i cannot ping it from across the network. The interfaces are up and happy. I have tried changing the VTP status from transparent to server (VTP pruning is off) ive tried setting allowed vlans 10,20. Still not a think. The worse thing is that i have a working Cisco switch with the HP procurve that i checked the config on and its the same! The only difference is that the media type is SX over SFP in that case.
p.s not that im at this stage yet but i initially configure the FastE ports as trunks with native vlans because i was using non-cisco phones. On a spare port i convigured the voice vlan 20 and i say on the mitel phone that it was looking on vlan20! I didnt expect that, i thought the Voice VLAN ID was carried on CDP enabled devices only.
I have a connection between switches, There are a 3560 (Gi0/37) and a 2960 (Gi0/1), the problem is in the port Gi0/37 of the 3560 switch and this is the log. [code]
I dont understand what is the problem, actually i have added the command power inline never on the port and the problem is solved, but we haven´t changed configuration.
I have a 3560 8 port switch. Int gi0/9 is trunked to another switch downstream. When I try to configure int gi0/10 to trunk to a switch upstream the interface on the switch goes down and I have to either reboot the switch or plug directly into the switch and telnet into it to turn off trunking on the interface. When I configure trunking on the interface on the upstream switch that connects to this interface the same happens on that switch. The upstream switch is a 3750 with 12 sfp ports. Several interfaces are trunking to other switches from this switch. Spanning tree is not configured on the 3750 at all , and is not configured on either gi0/10 or gi0/9 on the 3560. I was consoled into the 3560 during a reboot after the interface went down, a message came up that said something like "Spanning Tree returning gigabit ethernet 10 to constant state" Why would I get this message if spanning tree is not enabled on the gig ports on either end of the trunk? There is no loop to require spanning tree to shut down an interface. I have several other 3560's configured as I would like to configure this switch and they are trunking without issue.
View 8 Replies View RelatedIm having problems changing a connection between a Cisco3560 and Cisco IBM Blade switch 3012 actually the configuration is access in Cisco 3560 and trunk int Cisco 3012 when i change the connection to trunk i lose conecctivity to the servers connected in the 3012, i have changed the access from vlan 1 to the respective vlan in the access port of the servers
View 5 Replies View RelatedHaving problem pinging from Host A on ESX1 to Host B on ESX2. Each host are assigned the same port-profile. If I put 2 host's on the same ESX machine using the same port-profile, they are able to ping each other.
n1kv-vsm# sh port-profile name xxx-prod-40port-profile xxx-prod-40 description: type: vethernet status: enabled capability l3control: no pinning control-vlan: - pinning packet-vlan: - system vlans: 1 port-group: xxxl-prod-40 max ports: 32 inherit: config attributes: switchport mode private-vlan host switchport private-vlan host-association 40 400 no shutdown evaluated config attributes: switchport mode private-vlan host switchport private-vlan host-association 40 400 no shutdown assigned interfaces: Vethernet3 Vethernet4
System-uplink profile is trunking all vlans.
have setup a small lab as per CBTNuggets. Everything was going well until I introduced a second switch to create a trunk. Now I cannot ping between my two switches. Both show operational mode as down:
SWITCH1#show interfaces f0/12 switchport
Name: Fa0/12
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: down
Administrative Trunking Encapsulation: dot1q
[code]....
I have tried to allow all vlans or vlan 1 specifically and the output of the above doesn't seem to change. I am wondering if there is something in the config-register that is preventing trunking, but I don't really know enough yet!
The output of my second switch is identical to this one, the only difference is that I have it configured as a vtp client.
does SG200 support VLAN Trunking?
View 1 Replies View RelatedBetween our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedHow Can i Connect two switches 4505 using the trunking method,…
View 1 Replies View RelatedI have a number of class-'c's as a hand-off from my data center fiber to my 2960, which then sprawls the racks with about many 2950 switches, mostly 20 machines per switch. To allow machines on one 2950 to push data to another 2950 without routing back to my ISP's router(which costs money for bandwidth) isn't is possible to trunk one port on each 2950 to another 2950 and adding a addititional vlan8 to them. Then data jumps from 2950 to 2950 without going back to the 2960 or mainly not going back to my ISP's router. Is this the correct way to accoplish this with extra vlan and trunking the 2950's to each other or am I looking at this all wrong?
View 1 Replies View RelatedIs there any way to check if this VLAN is used by somedevice?
Cisco3560#sh ip int b
Vlan55 unassigned YES NVRAM administratively down down
Cisco3560#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
55 Print active Fa0/5, Fa0/6, Fa0/7, Fa0/8
I have 4 vlan and all has conectivity/access with all (VLAN10,VLAN20,VLAN30 and VLAN40, I use a 3560 Switch for this propose, I need to modificate one vlan (VLAN40) that has access to the rest of the VLAN's BUT the rest of the VLAN's dont have access to VLAN40. I know that it is a problem of access-list BUT I can't undertand how to obtain the result that I like
View 1 Replies View RelatedI have 2 locations, at a distance of 600KM.These two locations are well connected by Point to Point L2 VLAN with a speed of 2 MBPS and supported by CISCO 3560G switches.Location A has a VLAN to communicate to the other VLAN at Location B. Location B has also got 3 VLANS which are inter connected with Location A.Now the hardware in one of VLANs in Location B has moved to Location A for obvious reasons.
For further refernce am giving the VLAN IP address here....
Location A
VLAN1 for communicatng to Location B
IP Range 172.20.44.210
Subnet Mask 255.255.255.0
Default Gateway 172.20.44.210
VLAN2 for the desktops in Location A
IP Range 192.193.194.1-255
Subnet Mask 255.255.255.0
Default Gateway 192.193.194.1
[code]....
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies View RelatedI have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
Topology: 3560 <-access-mode-link-> ASA5510 - Internet,3560 has 3 VLANs and 3 corresponding SVIs (default-gateways for VLANs),Just configured RAS VPN on ASA5510 and successfully made connection,Now, from RAS VPN (IPSEC) client workstation CLI, can ping all 3560 SVIs,CANNOT PING host devices plugged into switchports.
View 1 Replies View RelatedIn my lab setup i configured Cisco 3560 switch.
-VLAN 20 and VLAN 30 i configured.
-VLAN 20 interface IP : 192.168.20.1/24
-VLAN 30 interface IP : 192.168.30.1/24.
Inter-vlan communication is happening fine. For testing for purpose i configured extended ACLs.i want stop communication from VLAN 30 to VLAN 20 but not vice-versa. If i ping from one of the IP VLAN 20 to one of the ip of VLAN 30, i was gettng Requested time out. And if i ping from one of the IP VLAN 20 to VLAN 30 interface IP, i was able get pinging.From VLAN 30 to VLAN 20, i was getting destination host unreachable from VLAN 30 ip( Its fine as its my requirement)So, solution needed to communicate from VLAN 20 to VLAN 30.
I have a 3560 switch with the following ports config [code] I would like to use theses ports on a different vlan to connect 4 pc's to them. Can I just remove them from the vlan, remove the trunk switchport and set up on the vlan i want them on with no trunking?
View 5 Replies View RelatedProbably an easy fix but something's weird in my config. I am setting up a new network, so this is not production, Routed environment, down to the access layer using 3560-x l3 switches.
vlan 10: data
vlan 20: wifi
vlan 30: wifi guests
vlan 40: voip
My objective is to allow all traffic OUTBOUND to certain subnets (10.10.0.0/24, 10.10.100.0/24, 10.10.110.0/24 10.10.120.0/24) and block any other 10.0.0.0/8 networks. By doing it this way, after blocking all other internal traffic, I allow everything else to ensure internet traffic can go out.
Extended IP access list VLAN10_TRAFFIC_FLOW 10 permit ip any 10.10.0.0 0.0.0.255 20 permit ip any 10.10.100.0 0.0.0.255 30 permit ip any 10.10.110.0 0.0.0.255 40 permit ip any 10.10.120.0 0.0.0.255 50 deny ip any 10.0.0.0 0.255.255.255 (5 matches) 60 deny ip any 172.16.0.0 0.0.255.255 70 permit ip any any!interface Vlan10description DATAip address 10.104.10.1 255.255.255.0ip access-group VLAN10_TRAFFIC_FLOW outendThe problem is, from the above info, when I ping 10.10.0.5 from a workstation in VLAN 10, it should match rule 10, but instead if matches rule 50 (as shown by the 5 matches)
When did this wonderful feature get introduced? Is it going to moved down to the 3560s/2960s type switches?
View 0 Replies View RelatedI faced the ( receive discard vlan 20 of Cisco switch 3560 ) on my Solarwinds Server .
View 1 Replies View RelatedWe have over 30 Cisco 3560 switches and over 10 VLANs on our network. In our example, VLAN 10 on switch IP 10.0.20.150 works fine and VLAN 10 on switch IP 10.0.20.24 doesn’t work. The below are both switches show vlan. url....I can’t tell what causes the problem and how to fix it. VLAN 10 on Switch 10.0.20 24 doesn’t work. [code]
View 8 Replies View RelatedI have enabled IP DHCP snooping on a 24 port 3560 switch (v small office) and let the database fill up, now I have added dynamic arp inspection on the single vlan and I amd getting these errors.
Apr 23 16:15:34: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/5, vlan 1.([5835.d9b0.b9d1/172.30.5.2/0000.0000.0000/172.30.5.3/16:15:33 BST Tue Apr 23 2013])
Apr 23 16:15:39: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:39 BST Tue Apr 23 2013])
Apr 23 16:15:40: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:40 BST Tue Apr 23 2013])
[Code] .....
I'm configuring two etherchannel groups (2 ports in each) on a 3560 switch. I need to trunk multiple vlans over each channel group.
I created the vlan trunks and allowed vlans on each physical interface. I notice that I can also configure the vlan trunks on the port-channel interfaces that were created. Should I configure them under those interfaces, or leave them on the physical interfaces? Relevant config is below:
interface Port-channel1
!
interface Port-channel2
[Code].....
For many years we've had the following vlan and port security config on our 3560s: [code] This has worked great on 12.2(37)SE1, 12.2(40)SE and 12.2(46)SE. However since 12.2(50)SE, and I've tried all the versions since then, we have a problem with 7900 phones and ATA186s taking upwards of 20 minutes before they can get a valid IP number.The problem on the newer IOSes seems to be related to the inactivity aging.On the older IOS versions the mac address of the voice device appears on the voice vlan straight away.
On the newer IOS versions the mac address of the voice device appears on the DATA vlan and seems to be stuck there until the inactivity aging removes it. It then gets re-learned, sometimes on the voice vlan, and sometimes on the data vlan. If you're unlucky and it gets re-learned on the data vlan you've got to wait until the inactivity time ages the address out again. Repeat until the mac address eventually gets learned on the voice vlan. I don't want to be stuck on 12.2(46)SE forever.
I've set up my 3560 to do routing. Now, I'm looking for a way to apply acl restrictions to the vlan interface ip address itself.
View 1 Replies View RelatedWe bought a 3560 PoE switch to replace tons of PoE-injectors but when connecting the devices our logs were flooded with
Mar 11 15:09:20.725: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD
Mar 11 15:09:20.725: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied
Mar 11 15:09:20.968: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down
Mar 11 15:09:20.985: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD
Mar 11 15:09:20.985: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied
While the message seems quite clear im wondering if there's any workaround on the problem?
I need to implement the shaping VLAN only on the trunk link between the 6500 and 3560. [code]
View 8 Replies View RelatedAny way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
We are using mac authentication, it is working fine on all of the other 3560's except this new one.
Mac address shows up completely different (very long hex, doesnt even look like a mac address) on ACS compared to what its showing on the switch in the mac address table.
Im stumped, config matches every other 3560 in the building, has something changed in the v2 software compared to the older 3560's ?
I'm new to networking and was looking for some assistance. First off im using packet tracer to diagram my senario as I will be receiving my equipment next week to deploy.
Hardware to be used:
1. 2 catalyst 3560 switches
2. all connect to a sonic wall router
I have two companies that work in the same office space. I need to keep these companies seperate on their own vlan. They will however need to share the phone system.(Packet tracer file uploaded to give those who have the time to see what I put together.) [code]