Cisco Switching/Routing :: 3560 CG Port Goes Down When Configuring Trunking
Jan 31, 2012
I have a 3560 8 port switch. Int gi0/9 is trunked to another switch downstream. When I try to configure int gi0/10 to trunk to a switch upstream the interface on the switch goes down and I have to either reboot the switch or plug directly into the switch and telnet into it to turn off trunking on the interface. When I configure trunking on the interface on the upstream switch that connects to this interface the same happens on that switch. The upstream switch is a 3750 with 12 sfp ports. Several interfaces are trunking to other switches from this switch. Spanning tree is not configured on the 3750 at all , and is not configured on either gi0/10 or gi0/9 on the 3560. I was consoled into the 3560 during a reboot after the interface went down, a message came up that said something like "Spanning Tree returning gigabit ethernet 10 to constant state" Why would I get this message if spanning tree is not enabled on the gig ports on either end of the trunk? There is no loop to require spanning tree to shut down an interface. I have several other 3560's configured as I would like to configure this switch and they are trunking without issue.
View 8 Replies
ADVERTISEMENT
Apr 3, 2008
We're trying to configure our Cisco 4507 (Supervisor Engine IV) to allow a new Dell server with a pair of Broadcom 5708 GigE NIC's to aggregate its NIC's to give us a 2gbps link to the switch.
So far we seem to have got the team and LACP up and enabled, but the adaptor that the Broadcom Admin Util creates for the team is only showing a 1gbps connection where I would have expected it to show as 2gbps.
The individual NICs show as connected at 1gbps. We're not Cisco experts so are struggling on how to get the 2 NICs to aggregate.
On the server side we've done nothing other than create a team using 802.3ad LINk Aggregation using LACP.
This is what I think the relevent output from "sho conf" is, more available if needed.
version 12.2
boot system flash bootflash:cat4000-i9s-mz.122-18.EW1.bin
!
interface Port-channel2
[Code].....
View 3 Replies
View Related
Nov 18, 2012
Im having problems changing a connection between a Cisco3560 and Cisco IBM Blade switch 3012 actually the configuration is access in Cisco 3560 and trunk int Cisco 3012 when i change the connection to trunk i lose conecctivity to the servers connected in the 3012, i have changed the access from vlan 1 to the respective vlan in the access port of the servers
View 5 Replies
View Related
Apr 25, 2012
I have a connection between switches, There are a 3560 (Gi0/37) and a 2960 (Gi0/1), the problem is in the port Gi0/37 of the 3560 switch and this is the log. [code]
I dont understand what is the problem, actually i have added the command power inline never on the port and the problem is solved, but we haven´t changed configuration.
View 3 Replies
View Related
Jun 3, 2012
We have two Cisco switches with one 3560 and one 3750 we have created a new Vlan 4 with IP 10.1.3.x 255.255.255.0 - no shut then assigne to gi 2/0/46 on the 3560 Vlan 4 ip address 10.1.3.x 255.255.255.0 no shut then assign to FA0/45. All interfaces are up up along with the Vlan up up, we can ping the local IP address bu not able to pint the other switch.
View 2 Replies
View Related
Jan 12, 2010
I have a HP Procurve 5406 connected to a Cisco 3560 on a temporary cat5e connection and I have Mitel IP phones needing to go on the Cisco switch.Ive configured the HP Procurve port to TAGGING both VLAN 10 (data) and VLAN 20 (Voice). NO is selected for default VLAN 1.The Cisco is configured on the port with switchport encap dot1q and switchport mode trunk.
Ive configured an IP for interface VLAN 10 and i cannot ping it from across the network. The interfaces are up and happy. I have tried changing the VTP status from transparent to server (VTP pruning is off) ive tried setting allowed vlans 10,20. Still not a think. The worse thing is that i have a working Cisco switch with the HP procurve that i checked the config on and its the same! The only difference is that the media type is SX over SFP in that case.
p.s not that im at this stage yet but i initially configure the FastE ports as trunks with native vlans because i was using non-cisco phones. On a spare port i convigured the voice vlan 20 and i say on the mitel phone that it was looking on vlan20! I didnt expect that, i thought the Voice VLAN ID was carried on CDP enabled devices only.
View 9 Replies
View Related
Jan 29, 2013
We have 2x WS-C3560X-48 with the 10Gb SFP C3KX-NM-10G module.I want to use the 10Gb SFP (with a redundant 1Gb link) between each of the switches.Below is the configuration what I think I should use. Is this correct?
SWITCH1
int TE1/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
[code]....
We also want to utilise Link Agrrigation for the servers that attach to the switch. Would this config be correct?
port-channel load-balance src-ip
int range x
switchport mode access
switchport access vlan 1 (They are all on the default vlan)
spanning-tree portfast
channel-group x mode active
(Then I would configure the LACP config on the server) Is there anything I am missing?
View 9 Replies
View Related
Nov 19, 2012
i have a 3560 connecting to a sp with limited bandwidth. i have one interface on the switch whose traffic i do not want to drop. i want this traffic to go into the high priority queue. i am not sure how this should be configured, but here is my best guess and my current qos configuration on the switch:
qos map cos-dscp 0 8 16 26 32 46 48 56
mls qos srr-queue output cos-map queue 1 threshold 3 5
mls qos srr-queue output cos-map queue 2 threshold 1 4 6 7
mls qos srr-queue output cos-map queue 2 threshold 2 3(code)
since cos 5 is mapped to dscp 46 then this traffic would go into the priority queue. is this correct ?
View 7 Replies
View Related
Jan 30, 2012
I have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
View 1 Replies
View Related
Mar 29, 2012
As per my attached diagram, I have three switches (Cat 3560-E and couple of Cat 2960-G)
Each PC is on different vlan
PC -1 on vlan 100
PC-2 on vlan 200
I need to connect PC-1 and PC-2 to the server. Server has no fixed vlan and can be changed.
Restrictions:
1) can’t change PCs vlan assignment.
2) can’t add 2nd NIC in the server.
I’ve tried private vlan but it requires separate physical ports for host and/or community vlan and somehow it did not work. I could be wrong Trunking using dot1q enabled on port 2 on all switches and connection works fine (server to PC-1 or server to PC-2) by enabling switchport access vlan 100 or switchport access vlan 200. However I need port 5 on switch-1 to respond to vlan 100 and 200.
View 11 Replies
View Related
May 25, 2012
I currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 10 Replies
View Related
Jul 11, 2012
Is it posible to config port forwarding on cisco 2950 or other switchs.if such a option is there ple let me know ho to config port forwarding on cisco 2950 switch..
View 1 Replies
View Related
Oct 21, 2012
I've just installed 2 of these in my workplace on a PLC network.I'm now looking to set one of the ports up as my diagnostic port and would like to be able to mirror any of the other ports to this port.I believe it is called SPAN on Cisco switches.The only reference I can find to it is configuring via Telnet which I haven't got a clue about.On my old Wiedmuller switches it was just a few clicks away.
View 3 Replies
View Related
Apr 18, 2012
I have a 3560 switch with the following ports config [code] I would like to use theses ports on a different vlan to connect 4 pc's to them. Can I just remove them from the vlan, remove the trunk switchport and set up on the vlan i want them on with no trunking?
View 5 Replies
View Related
May 1, 2013
Our enviornment includes 3560 switches and 2800 routers. We have a few remote offices using an application on TCP port 1677 that use far to much bandwidth. Our WAN provider can throttle and police this for us, if I can TAG this traffic, for example all Traffic from Florida using the Groupwise app on TCP uses TCP port 1677 and I want it tagged with CoS 3.
View 1 Replies
View Related
May 2, 2013
We've been configuring our swtichports as follows for our 7945 and 6941 type VoIP Phones, but are having problems witht the 6901.
VLANS
Vlan 900 is a VoIP VLAN
Vlan 999 is a NULL VLAN and is shut down:
interface g0/1
switchport access vlan 999 {VLAN to direct data traffic to the bit bucket becuase a PC shouldn't be connected to this port}
switchport mode access
switchport voice vlan 900
mls qos trust cos
spanning-tree portfast
The 6901 phone doesn't support multiple VLANs, so our configuration above does not work unless vlan 999 is turned on (not good security wise). We got the phones to work also by removing vlan 999 and switchport mode access.
switchport voice vlan 900
mls qos trust cos
spanning-tree portfast
solution that provides the discarding of data for the access VLAN, while supporting the VoIP vlan for this phone?
View 3 Replies
View Related
Mar 2, 2012
I have two servers, connected on two(Different) 6513 directly connected switches. Both these servers are in the same Vlan.
I have to monitor communication these two servers. I have a system connected on one of the 6513 switch, where network tool wireshark is installed.
How to configure span port.
switch 6513-1# show run int Gi10/43 --------------------Server 1 is connected
switch 6513-2# show run int Gi9/45 ------------------------Server 2 is connected
switch 6513-2# show run int Gi9/46 ------------------------System on which network tool wireshark is installed.
View 9 Replies
View Related
Jan 3, 2012
I want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
View 3 Replies
View Related
Mar 3, 2012
I am using 3560.IP rouitng is being turned off on this.Curious to know if I will create etherchannel or port channel.I think etherchannel.Correct me if I am wrong.On connecting switches I have vlan10,20,30 to be allowed.I am sure I need to allow these all vlan in 10,20,30 which are on the trunk port on each side switch.Post that will add channel-port lacp and make it in active mode.Is that correct.This way traffic will be load-balanced/aggregated on minimum 2 ports who are the part of this.
View 2 Replies
View Related
Mar 6, 2013
Problem is that at some C65K I have directly connected Unix servers and the don't show MAC address at port, and same has happened at 3560 switched where I have too Unix based equipments connected. When use show mac-address interface XXXX, nothis appears at port and tested them with other equipments that worked fine.
View 2 Replies
View Related
Apr 10, 2012
Assume I had Catalyst 3560X/3750X with 24 ports. The partnumber is WS-C3560X-24P-LI would like to how is the numbering defined if the switches have a C3KX-NM-10G installed with 4 SFP-GE-L.
View 1 Replies
View Related
Sep 21, 2012
We have 7 3560's in 7 different locations connected to our providor for wan access. Our provider has given us a copper cable at each point and we have connected it directly to our 3560 switch at each location. Each port is configured the same way at each location. Each switch is running eigrp.All of the switch ports on each switch are configured as a trunk and vlan 299 had the ip address for the eigrp connection: [code] This setup is working as each switch see's all of the other switches as an eigrp neighbor. We have also made sure that the switch at our head office has spanning tree priority for vlan 299.
So the problem is, if there is a change in the topology at one of the locations it usually causes one or more of the other connections to go down for some reason. We just cannot pinpoint what is causing this change. There are no log's or anything other than an eigrp hold time expired message.?
View 9 Replies
View Related
Jul 10, 2012
I have a pair of 3560's configured with dot1q trunks between them carrying a number of VLANs.
Once deployed there will be a requirement for these physical trunks to be disconnected from time to time. Knowing that this is inevitable I am trying to minimise the period of time for the trunks to recover once the physical connectivity is reinstated.
All of the VLANs on the switches are configured for Spanning Tree Rapid PVST. Current time for the trunks/VLANs to come up is around the 4 second mark.
View 11 Replies
View Related
Apr 11, 2012
I would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies
View Related
Apr 1, 2012
my current network setup is like this.. a cisco 3560 is connected on an access port to an adjacent dlink stack. i want to enable trunking between the cisco and the dlink. what i know is that dlink doesnot support per vlan STP while dlink only run single instance of the STP.. how can i make the trunking possible without messing with the network.
the idea that i have is to run MSTP instance on the 3560 so that it appears as a single STP to the dlink switch and then all good. is there any other way to do that. if i just make both the adjacent ports on both the switches as trunk and connect them, will it cause any problem in terms of STP issues or convergence ?
View 1 Replies
View Related
May 20, 2010
For many years we've had the following vlan and port security config on our 3560s: [code] This has worked great on 12.2(37)SE1, 12.2(40)SE and 12.2(46)SE. However since 12.2(50)SE, and I've tried all the versions since then, we have a problem with 7900 phones and ATA186s taking upwards of 20 minutes before they can get a valid IP number.The problem on the newer IOSes seems to be related to the inactivity aging.On the older IOS versions the mac address of the voice device appears on the voice vlan straight away.
On the newer IOS versions the mac address of the voice device appears on the DATA vlan and seems to be stuck there until the inactivity aging removes it. It then gets re-learned, sometimes on the voice vlan, and sometimes on the data vlan. If you're unlucky and it gets re-learned on the data vlan you've got to wait until the inactivity time ages the address out again. Repeat until the mac address eventually gets learned on the voice vlan. I don't want to be stuck on 12.2(46)SE forever.
View 11 Replies
View Related
Dec 17, 2012
How do I limit broadcast/mulitcast traffic on a switchport to e.g. 5000 pps ? I don't want the port to shut down, just block or drop broadcast traffic that exceeds 5000 pps.
View 19 Replies
View Related
Nov 5, 2012
Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q
[Code].....
View 3 Replies
View Related
Feb 19, 2012
In one location we have a HP 2510-48 port switch which we need to connect to a Cisco 3560 switch. The problem I have is that we have issues connecting fibre to the HP switch, so I have decided to attached a CAT 5 to Fibre convertor at this end and another to the cisco switch.
My question you can not connect a HP switch to a Cisco switch, is this true or do I just need to confirgure something on the ports.
View 2 Replies
View Related
Feb 21, 2013
I'm intending to purchase a switch for work,and I need to limit the bandwidth of one of the ports to 25 Mbit upload and 25 Mbit download (we have 100/100 Mbit connection and the customer is only paying for 25). I been trying to find information on how this could be "properly" done and what kind of switch I need to buy. As far as I have understood, most L2+ switches support outbound rate limiting, but not inbound, and as I only want the customer to have 25 mbit up and down, I need both.
I been looking at a Cisco Catalyst 3560 switch, and I'm first and foremost wondering if I can limit the inbound AND outbound bandwidth on this switch? Perhaps it can even be done on a simpler, cheaper, switch - as I rather not spend more money then necessary?
Lastly, how to do it, limit the inbound and outbound bandwidth on a single port (perhaps on the above mentioned switch, if possible), to 25 Mbit?
View 3 Replies
View Related
Feb 5, 2013
I have 3560's in my current environment, operating in the core/distro/access layers. The switches are in a star configuration, performs only layer 2 switching, and utilizes copper (no plans on moving to fiber).
With a fairly limited budget, I've been contemplating on upgrading the central node to a stacked 3750X to eliminate that single point of failure, and trunk the rest of the 3560's to the stacked switch. I wanted to be sure that the 3750X switches will be right for my environment (90-100 hosts), and if what I explained above is a good solution.
I'm also looking like to upgrade 6-7 of my servers (and SAN) with 10GB network cards. Do the ports on the 3750X have port densities capable of 10GB? If not, what switches provide that capability?
View 10 Replies
View Related
Oct 11, 2010
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
View 8 Replies
View Related
Feb 28, 2013
I have 2 3560 switches that are running 12.2(25)SEE2. Port security is enabled on some of the ports. Whenever there is a power failure, when power is restored, 1 port on each switch goes to err-disabled. The mac address that causes this is a valid address for that port. Below is the configuration on one of the ports.
View 1 Replies
View Related
