Cisco Switching/Routing :: Port / MAC Based DHCP For 2960 And 3560
Jan 3, 2012
I want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
View 3 Replies
ADVERTISEMENT
Nov 15, 2012
Does the 2960 switches with LAN-Lite support DHCP Server Port-Based Address Allocation?
View 1 Replies
View Related
Apr 9, 2013
I am upgrading from 3750-E IOS 12.2 to 3750-X IOS 15.0
I have a dhcp pool set up to give out an ip address based on the Physical port of the switch. I also have it configured to give out "reserved only" addresses.
The configuration works when i plug a dhcp device in the 3750E. (IOS12.2) The configuration does not work when i use the same config on 3750X (IOS15)
When i debug dhcp, i see the DHCP discover message come in, but no offers or anykind of response from the 3750X.
If i remove the "reserved only" line the switch gives out IPs, but of ocurse not the ones i want. I did that to prove both the client and the switch can give out an IP.
So i have a feeling the subscriber-id client-id interface name mapping is not right, or not created.
Here is a snippet of config.
!
no ip dhcp use vrf connected
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
[Code]......
View 1 Replies
View Related
Jun 24, 2012
I need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
View 1 Replies
View Related
Apr 19, 2012
Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop" do not do the same job.
View 8 Replies
View Related
Apr 17, 2012
I have tried to make policy based routing on Cisco 3560. I use ipservices ios (SW version 12.2.(50)SE3 and SW-IMAGE C3560-IPSERVICESK9-M) For below configuration there is no problem and pbr is working.
“Access-list 100 permit ip host 1.1.1.1 host 2.2.2.2
Access-list 101 permit ip host 1.1.1.1 host 3.3.3.3
Route-map pbr1 permit 10
Match ip address 100
Set ip next-hop verify-availability 1.1.1.2 1 track 11
interface fasthethernet 0/1
ip policy route-map pbr1”
But when i add another sequence to the "pbr1" with another sequence number like that.
“Route-map pbr1 permit 11
Match ip address 101
Set ip next-hop verify-availability 1.1.1.3 1 track 12”
pbr is not working. Switch gives message "PLATFORM_PBR-3-UNSUPPORTTED_RMP:Route-map pbr1 not supported for Policy Based Routing”"ip policy route-map pbr1" command not shown in the running config. And "show ip policy" output is blank.Configuration guide says you have insert many sequence to the route-map with the same name. And also this command is not in the unsupported command list.
View 16 Replies
View Related
Jun 24, 2012
I'm trying to connect Switch 3560 to NTP Server based on Linux, the NTP is working fine but the switch is sync with the Server:
address ref clock st when poll reach delay offset disp
*~10.0.0.70 208.53.158.34 3 42 64 377 1.7 -2.49 0.1
* master (synced), # master (unsynced), + selected, - candidate, ~ configured
Clock is synchronized, stratum 4, reference is 10.0.0.70
nominal freq is 119.2092 Hz, actual freq is 119.2093 Hz, precision is 2**18
[code].....
But server has on time and the Switch another. I test this NTP with CUCM and is working fine, the issue is with ther server?
View 9 Replies
View Related
Dec 11, 2011
I need to enable/disable a mac access-list on a 2960 scheduled by time. The switch has lanbasek9-mz.122-44.SE6. As the mac access-list can not support time ranges, I tried EEM but seems like it is not supported in this device.
View 1 Replies
View Related
Dec 13, 2011
From the multiplexer 9 ethernet connections are terminating in Cisco 2960G 24 port swith and it is connected through fiber uplink to one Cisco 3560G 48 port switch in first floor, which is connected to server.
How I will configure the 3560G to make communicate with 2960G and bring all these 9 ethernet connections to server. All the 9 connections are from different IP. and server also have different IP.
View 1 Replies
View Related
Dec 28, 2012
It seems my 2960s and 3560s switches have enough flash space and memory to support the 15.0 IOS should I be OK to jump to this from 12.2(35)?
View 10 Replies
View Related
May 15, 2012
I'm having issue with one stubborn process that is consuming nearly all the CPU on all of my switches. I tried googling it, but had no luck. The process is "hulc nrgyz PD di"
View 4 Replies
View Related
Jul 26, 2011
Yesterday Cisco released IOS 15 code into the wild for the 2960 and 3560/3750 families but the link to the release notes is not working. Because I already have a whole bunch of 4500/Sup7's running IOS 15 I am thinking about taking the plunge with 30 3750-X's I have on order but want to review the release notes first. where they might be hiding?
View 4 Replies
View Related
Sep 13, 2012
I have CISCO RPS 600 (PWR-AC-RPS) is it support Catalyst 2960 and 3560 ? and which type of cable require since i have cable 22-18 pin and on my switch require 22-14 pin.
View 2 Replies
View Related
Aug 6, 2012
When did this wonderful feature get introduced? Is it going to moved down to the 3560s/2960s type switches?
View 0 Replies
View Related
Jul 10, 2012
I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
View 4 Replies
View Related
Mar 12, 2013
I know only one method to restart Cisco switch through Telent using command " RELOAD". How can we restart Cisco 2960/3560 switch phyically....can i use mode button to restart cisco switch ?
View 11 Replies
View Related
Feb 6, 2012
Is it possible to daisy chain from a 3560 to 2960-S switch using a SFP interconnect cable (daisy chain cable)
View 1 Replies
View Related
Jun 7, 2011
We have quite a few 3560 & 2960 on our edge network - what I have been looking at was to access switches via web-interface i.e. web-browser. Only problem with this is it always gives you access on privilige level 15 which is not ideal as not all who we decide to give access to these switches will be admin and allowed to configure these swicthes - In the 3560/2960 data-sheet states:
"Alternatively, a local username and password database can be configured on the switch itself. Fifteen levels of authorization on the switch console and two levels on the Web-based management interface provide the ability to give different levels of configuration capabilities to different administrators"
Where as there is no mention of how to configure these two levels of Web-based management in the configuration guide.
View 8 Replies
View Related
Jan 21, 2013
As per the attached diagram: How do I configure the 2 ports on the 3560 (Ports 6 & 7) and the connected ports on each of the 2960 switches (Port 25) to provide redundancy.
If the up link from Switch A dies then I need the traffic to flow through the trunk and utilize the up link on Switch B with minimal delay (milliseconds).
View 9 Replies
View Related
Oct 16, 2011
I have a Cisco 3560 running as a Level3 device in my network running 10 V LANs and routing between most of them (nothing complex with ACLs) and running spanning-tree mode pvst. The main network is run on a net gear GS748TPS stack of three switches running MSTP.
I have just bought an additional 3560 and a 2960 to plug in. I have set them up with IP addresses and then plugged them into the net gear. This brought the whole network down until I unplugged the new switches.
I have confirmed the IP addresses aren't duplicated and that DHCP is not running on the switches so I can only assume it's something to do with DHCP. I cannot afford for the network to go offline again, so is there anything I should check? Am I running incompatible spanning tree methods between the net gear and Cisco devices?
View 28 Replies
View Related
Jan 30, 2012
I have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
View 1 Replies
View Related
Apr 12, 2012
Would like to impliment VLAN's on Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(25)SEB4...But I need a DHCP Realy to my Windows Based DHCP Server. How do I enable DHCP Relay on the 3560?
View 8 Replies
View Related
Oct 9, 2012
I am using Packet Tracer to simulate Cisco networking.As the existing IOS of the 3560 and 2960 switch are in older version which has no new feature in new IOS, how to upgarde the IOS of Cisco switch at Packet Tracer?
View 5 Replies
View Related
Oct 12, 2011
I have attempted to implement DHCP snooping and have been having some strange issues. I have 5 3560s taht I use for my edge and when I attempt to implement on all five, the VLAN that houses my voice data appears to no longer be able to recieve DHCP lease renewals so after the 24 expiration all of my phones lose their configs. Once I roll back the changes the voice VLAN comes back. The other VLANs seem to function correctly as theya re able to renew their DHCP addresses.
The 3560s tie into each other using GIG Ports 1 & 2 and the top and bottom switches tie into our core switch, a 4507. The config that I use is below, failry simple and straightforward.
4 of the 5 switches feed our general office vlans for voice and data however the 5th switch is there for expansion and not in use. As such I have left the config changes in place on it and have tied myself and a colleague into it and have been operating fine for over a week now. So the config that I use seems sound in theory and should work on the other 4 switches with no issue.
View 14 Replies
View Related
May 25, 2012
I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.
View 3 Replies
View Related
Jul 23, 2012
I have a cisco 3560 24PS and its connected to two ADSL broard band routers.one is a personal broadband line using a Billion ADSL broadband router, and the other is a business broardband line using BT's 2wire broadband line.on the Billion routers i have various things attached like a NAS and a printers, both wired connections. then i have laptops and phones that connect over wifi, so its configured to act as a DHCP server
the only thing conncted to my 2wire router is my company's laptop (wired or wifi depending on where i'm working from), so again i have it working as a dhcp server.The switch is configured with multiple vlans, with dhcp scopes assigned for each vlan.I have a static route pointing all traffic to my Billion ADSL for internet connectivity.
The problem i'm having is that when i turn on the cisco switch, all wifi conected devices loose their conection. only 2 things get it working again, a reboot of the router, or disabling then enabling the DHCP service on the router.upon further analysis i was able to find out that the devices were not able to pick up an address from the router. again i looked deeper into this and i can see the following on logs of my router: [code]
so it seems that the router tuns off its DHCP capabilities because it detects that my Cisco switch is running DHCP services. I need to figure out how to keep the billion routers DHCP running when ever the switch is turned on.is there a way of filtering out any DHCP chat from the switch to the router?
View 7 Replies
View Related
Jan 18, 2013
I am trying to understand the basics of DHCP snooping. I have a just a 3560 switch and a laptop ( to get a DHCP address) and my DSL router which has a DHCP server running. On the switch I have enabled "IP DHCP Snooping" and "IP DHCP Snooping VLAN 1" plugged the laptop and DSL router in and the laptop gets and IP address, should it?
I thought all ports were untrusted by default so the DHCP server should be blocked at offering IP addresses? If I wanted the DHCP server to be allowed to offer IP's I thought I should need to trust the port.
View 3 Replies
View Related
Mar 5, 2012
Facing some DHCP issue. I got my laptop directly connected with Cisco 2960 switch. However it is not getting valid IP.
View 1 Replies
View Related
Jan 16, 2013
I have two WAP4410N plugged into my Catylist 3560 switches.One of these switches is my Default Gateway for the LAN.The only way I can get a device to connect to the WAP4410N is by assigning it a static IP. Then it works perfectly.
View 10 Replies
View Related
Mar 19, 2012
can you enable dhcp service on a 3560 switch.
View 3 Replies
View Related
Apr 26, 2012
I'm attempting to configure a Catalyst 3560-X Switch to act as a DHCP Server. There is documentation that supports this feature. Below is my config procedure however after the completed procedue no IPs are handed out to clients. [code]
View 1 Replies
View Related
Apr 29, 2012
we have a 3560 switch configured with EIGRP with dhcp. We have a user that we cannot ping, however the interface show up / up and no errors on interface. the ip address is 10.2.0.199 - however we have dhcp configured to exclude the range from dhcp ip dhcp excluded-address 10.22.0.1 10.22.0.200 how can this work station get a dhcp address if we have that ip range excluded from the dhcp pool?
The user is off a different switch that is a uplink to this distribution switch. Traceroutes shows that the problem is with the distribution switch.
View 4 Replies
View Related
Oct 21, 2011
I did the DHCP configuration for my CISCO 2960 switch but the clients are still not able to get the IPs.see the configuration below.
(config)#ip dhcp database cisco.com
(config)#pool test
(config-if)#client client-id vlan 500
(config-if)#ip dhcp snooping trust
View 1 Replies
View Related
