As per the attached diagram: How do I configure the 2 ports on the 3560 (Ports 6 & 7) and the connected ports on each of the 2960 switches (Port 25) to provide redundancy.
If the up link from Switch A dies then I need the traffic to flow through the trunk and utilize the up link on Switch B with minimal delay (milliseconds).
One of our customer , where there 2 6509 switch , one is Core_sw1 and other is Core_sw2 , catering about 32 Vlan , and HSRP in running for all Vlans , till here no problem , now there internet Router which having one Internet link , which connected and configured on Core_sw1 in a way that one interface of Core_sw1 is given Public IP and there is vlan 85 which internet vlan and vlan 85 ip are natted with that public IP with one simple static route given toward internet router , this is how internet is working ok.
Now i have configured vlan 85 in hsrp as all other are , how can give redundancy to vlan 85 user , that if Core_sw1 get down , internet traffic can get out through Core_sw2.using same internet router with single internet link .i am not talking of ISP redundancy , but Vlan 85 in Core_sw1 goes down , other Core_sw2 will server internet.
I have got two links from the same ISP, primary and secondary and connected to two different switch. The ISP have passed the trunk vlan of 30, 31 and 32 on both of the links. The ISP can't provide stp. I have got another managed 2960 series switch. How can I obtain failover on switch level.
View 2 Replies View RelatedI have upgraded my C3560-PS-S switch to the latest IOS version 12(2)55-SE4 and it is not providing PoE anymore? It used to work before this upgrade? I searched Cisco bugtrack and there is bug defined for this IOS/Switch.
Switch(config-if)#do show power inline Available:370.0(w) Used:0.0(w) Remaining:370.0(w)
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Fa0/1 auto off 0.0 n/a n/a 15.4
Fa0/2 auto off 0.0 n/a n/a 15.4
Fa0/3 auto off 0.0 n/a n/a 15.4
Fa0/4 auto off 0.0 n/a n/a 15.4
Fa0/5 auto off 0.0 n/a n/a 15.4
Fa0/6 auto off 0.0 n/a n/a 15.4
Fa0/7 auto off 0.0 n/a n/a 15.4
Fa0/8 auto off 0.0 n/a n/a 15.4
Fa0/9 auto off 0.0 n/a n/a 15.4
Fa0/10 auto off 0.0 n/a n/a 15.4
Fa0/11 auto off 0.0 n/a n/a 15.4
Fa0/12 auto off 0.0 n/a n/a 15.4
Fa0/13 auto off 0.0 n/a n/a 15.4
Fa0/14 auto off 0.0 n/a n/a 15.4
Fa0/15 auto off 0.0 n/a n/a 15.4
Fa0/16 auto off 0.0 n/a n/a 15.4
Fa0/17 auto off 0.0 n/a n/a 15.4
Fa0/18 auto off 0.0 n/a n/a 15.4
Fa0/19 auto off 0.0 n/a n/a 15.4
Fa0/20 auto off 0.0 n/a n/a 15.4
Fa0/21 auto off 0.0 n/a n/a 15.4
Fa0/22 auto off 0.0 n/a n/a 15.4
Fa0/23 auto off 0.0 n/a n/a 15.4
Fa0/24 auto off 0.0 n/a n/a 15.4
we are in the planning phase for a network upgrade. We have two C2960 Switches connected via one (L2) Etherchannel (4x1 Gbit/s) which works very well. In the next phase we would like to upgrade our router to an 2911 series which has 3 gb interfaces. and indeed we would like to create an etherchannel as well. our plan is to use 2 of the 2911 to connect to the first 2960 switch and the one left to the other 2960. i think we will achieve some redundancy with this config.
View 6 Replies View RelatedI'm using Packet Tracer for testing since I don't have the actual equipment. I have configured etherchannel between two 2960 Switches. I have used the trunk ports FE 0/23 and FE 0/24 on both switches to create the etherchanel. I have connected one PC with each switch. The PCs are in the same VLAN and can ping each other. Howver, when I take down one of the links in the etherchannel, the other link does not take over and I get 100% packet loss. I don't know what seems to be the problem. I'm quoting the configurations below:
Switch0:
Switch#sh running-config
Building configuration...
Current configuration : 1179 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
[code]....
My actual Scenario
1 x 4500 and 1 x 3560?They are gateways of 8 Vlans?They are doing HSRP in each of those Vlans?The 4500 is the Active?There is a DHCP Pool for each of those Vlans on both gateways using "ip dhcp excluded-address" I ensured that the range of provided ips by each DHCP server will not be overlapped Obs.: Reducing the lease time, I ended with the calls bringing related problems.
OK, every thing is blue, every thing is fine.But the network diagram is realy complex(41 switchs, 89 uplinks), and depending of how is the network flow, one or other server answer first or latter.
For many reasons I would like that the secondary DHCP server would answer only if the primary DHCP server goes down.To me, the bigger reason is that DHCP database would be only in one DHCP server.But there is other reasons.
I passed by many frustrated solutions:Try to force a delay on the answer on one of the servers. - Impossible.Try to disable DHCP server, and, using EEM, enable it only if router became active in HSRP. - I couldn't do It.
What I'm thinking now is use the HSRP resource to resolve it.On both routers I would put a "ip helper-address" pointing to an Virtual_HSRP_IP.And depending on which router is the active, him will answer the request.
My first doubt is:Would it work?The second doubt is:Could I use the same Virtual_HSRP_IP that exists on that Vlan(see example 1),or I would need to point it to a Virtual_HSRP_IP in a different Vlan(see example 2)?
Example 1
-----------------------------------
| 4500 |
-----------------------------------
interface Vlan1
ip address 10.10.0.2 255.255.0.0
ip helper-address 10.10.0.1
standby 1 ip 10.10.0.1
[code]....
I need to configure a 4507 chassis with two SUP 7 installed. I havenot done SUP redundancy comnfiguration and i was owndering
View 9 Replies View RelatedFrom the multiplexer 9 ethernet connections are terminating in Cisco 2960G 24 port swith and it is connected through fiber uplink to one Cisco 3560G 48 port switch in first floor, which is connected to server.
How I will configure the 3560G to make communicate with 2960G and bring all these 9 ethernet connections to server. All the 9 connections are from different IP. and server also have different IP.
It seems my 2960s and 3560s switches have enough flash space and memory to support the 15.0 IOS should I be OK to jump to this from 12.2(35)?
View 10 Replies View RelatedI'm having issue with one stubborn process that is consuming nearly all the CPU on all of my switches. I tried googling it, but had no luck. The process is "hulc nrgyz PD di"
View 4 Replies View RelatedYesterday Cisco released IOS 15 code into the wild for the 2960 and 3560/3750 families but the link to the release notes is not working. Because I already have a whole bunch of 4500/Sup7's running IOS 15 I am thinking about taking the plunge with 30 3750-X's I have on order but want to review the release notes first. where they might be hiding?
View 4 Replies View RelatedI have CISCO RPS 600 (PWR-AC-RPS) is it support Catalyst 2960 and 3560 ? and which type of cable require since i have cable 22-18 pin and on my switch require 22-14 pin.
View 2 Replies View RelatedWhen did this wonderful feature get introduced? Is it going to moved down to the 3560s/2960s type switches?
View 0 Replies View RelatedI would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
we hava a couple of 2960 switches and we are logging to a syslog server. Ports keep going up and down is it normal severity (error) ?
View 2 Replies View RelatedI know only one method to restart Cisco switch through Telent using command " RELOAD". How can we restart Cisco 2960/3560 switch phyically....can i use mode button to restart cisco switch ?
View 11 Replies View RelatedI want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
Is it possible to daisy chain from a 3560 to 2960-S switch using a SFP interconnect cable (daisy chain cable)
View 1 Replies View RelatedWe have quite a few 3560 & 2960 on our edge network - what I have been looking at was to access switches via web-interface i.e. web-browser. Only problem with this is it always gives you access on privilige level 15 which is not ideal as not all who we decide to give access to these switches will be admin and allowed to configure these swicthes - In the 3560/2960 data-sheet states:
"Alternatively, a local username and password database can be configured on the switch itself. Fifteen levels of authorization on the switch console and two levels on the Web-based management interface provide the ability to give different levels of configuration capabilities to different administrators"
Where as there is no mention of how to configure these two levels of Web-based management in the configuration guide.
have problem with switch. 3560, Some of gi ports have outdiscards errors and switching is very slow.
ServerSwitch>show int counters errors
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize OutDiscards
Gi0/1 0 0 0 0 0 8722
Gi0/2 0 0 0 0 0 157
Gi0/3 0 0 0 0 0 0
Gi0/4 0 0 0 0 0 0
Gi0/5 0 0 0 0 0 0
Gi0/6 0 0 0 0 0 446
Gi0/7 0 0 0 0 0 0
Gi0/8 0 0 0 0 0 0
Gi0/9 0 0 0 0 0 0
Gi0/10 0 0 0 0 0 0
Gi0/11 0 0 0 0 0 0
Gi0/12 0 0 0 0 0 1705658
Gi0/13 0 0 0 0 0 9
Gi0/14 0 0 0 0 0 74
Gi0/15 0 0 0 0 0 0
Gi0/16 0 0 0 0 0 0
Gi0/17 0 0 0 0 0 9
Gi0/18 0 0 0 0 0 0
Gi0/19 0 0 0 0 0 0
Gi0/20 0 0 0 0 0 0
Gi0/21 0 0 0 0 0 0
Gi0/22 0 0 0 0 0 0
Gi0/23 0 0 0 0 0 922
Gi0/24 0 0 0 0 0 0
But in monitoring i see only 80 Mbit max bandwith utilization on gigabit links.
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
New to Cisco and want to know if I can segment a port. I have two v lans. I have one internet connection at the opposite end of the building. Can the port the internet is connected to serve both V lans?
View 6 Replies View Related I have a Cisco 3560 running as a Level3 device in my network running 10 V LANs and routing between most of them (nothing complex with ACLs) and running spanning-tree mode pvst. The main network is run on a net gear GS748TPS stack of three switches running MSTP.
I have just bought an additional 3560 and a 2960 to plug in. I have set them up with IP addresses and then plugged them into the net gear. This brought the whole network down until I unplugged the new switches.
I have confirmed the IP addresses aren't duplicated and that DHCP is not running on the switches so I can only assume it's something to do with DHCP. I cannot afford for the network to go offline again, so is there anything I should check? Am I running incompatible spanning tree methods between the net gear and Cisco devices?
We are experiencing two of our layer 3 switches (3560 PoE and 3750 PoE) switches giving us problems with giving power to IP phones. These switches have an embedded PoE module and would previously give power to all IP phones on all its ports. Now all of a sudden over the past few months 6 of these ports have stopped powering phones. The phones are the same ie. 7911 and they take less than 15.4 W. We believe that the PoE module has started malfunctioning and has stopped giving power to all the ports. The port 'grants' power and then removes it. Below is a link showing all the messaged we receive on the terminal session. It is NOT a hardware fault with the PoE: [code]
View 2 Replies View RelatedI have a connection between switches, There are a 3560 (Gi0/37) and a 2960 (Gi0/1), the problem is in the port Gi0/37 of the 3560 switch and this is the log. [code]
I dont understand what is the problem, actually i have added the command power inline never on the port and the problem is solved, but we haven´t changed configuration.
it is possible to let cat3750 or 2960 ports which only allow machine on network which it use dhcp, not static ip? if so, how to configure it?
View 8 Replies View RelatedI have an doubt about some port in 2960.He have 2 SFP and 2 Fixed Ethernet. Can I use these 4 ports in the same time? Use 2 Ethernet and the 2 SFP with Fiber?
View 2 Replies View RelatedI have two questions for a Cisco 2960 (WS-C2960-24TC-L)
1. I am working to setup a few Cisco 2960 switches for HP iLO access to our servers. We are going to segregate the iLO network (VLAN 40) from the data network (VLAN 10) by using a different VLAN. All of the HP servers will be configured with static addresses. My question is, how do I set all the ports to VLAN 40 so that untagged devices will automatically go onto VLAN 40? I don't want to have to configure the VLAN on each iLO port on the server. I tried to set the port to: "switchport trunk native vlan 40", but that didn't work.
2. Also, how do you access the web GUI for these switches? I get a login box, but putting in the enable password doesn't work. I have the following commands in the config: [code]
We have a 2960 switch which is connected to the core via a VLAN trunk. We have disabled broadcast port suppression but, the 2960 is shutting is shutting 2 ports down on the network and this looks like excessive braodcast. How and why would the switch start dropping traffic when the default is don't do anything? It had to be rebooted to get the port active again
View 1 Replies View RelatedDisable ports looping Users connect the network cable at two points in the network generating looping. which command to disable two ports of a Cisco 2960 when they are connected at the same time with the same network cable?
View 2 Replies View RelatedI have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
I've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies View Related