I have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
we have cisco 2960 switch which is connected to a cisco 2811 router. flapping issue between these two devices??
The following actions i have taken, but no result.. I have changed cables. have set speed to 100 and duplex full on both the interfaces but the interfaces are showing up up still not getting connectivity. same i have to auto on both sides still no result what configurations should i set to resolve this issue...?
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
I have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies View RelatedWe have been receiving these notifications on one of our core.
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host b407.f9c3.3c51 in vlan 56 is flapping between port Po5 and port Te7/2
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 145a.05c8.0ed3 in vlan 802 is flapping between port Te7/2 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 9463.d129.546a in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 3c43.8ef3.7448 in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 000e.35eb.25ae in vlan 66 is flapping between port Po5 and port Te7/2
PO5 goes to our primary wireless controller. Gi2/9 goes to a Cisco 4500 switch that also has a PO5 on it for a failover lan controller and TE7/2 is another core switch.
These mac-address all seem to point to PO 5 which is the port channel assigned to Wireless Controller interfaces.
How do I determine if this is a spanning-tree loop? No ports are err-disabled.
Stange problem which I encountered today, I have a Cisco 2960 which is connected to a netgear. The switch started showing itself in CDP and was running STP. I checked the cables physically today and noted 3 uplinks to the netgear, all port on the Cisco active and forwarding and green lights.
The Cisco was running STP, I changed it to R-PVST and the lights on the Cisco went crazy and I got the message port flapping on the switch but the switch did not block any ports (all ports on same vlan).
There after I changed it back to stp and the switch blocked the other up links apart from one.
Sure R-PVST is far superior than STP?
Two days back my entire network was behaving in unusual ways.When is connect to core switc(4506e) through console. [code]
View 11 Replies View RelatedI am receiving the following error message on a Cisco 3750 switch stack. Need troubleshooting this error message.
00:03:13: %SW_MATM-4-MACFLAP_NOTIF: Host 00d0.7400.2730 in vlan 600 is flapping between port Gi2/0/3 and port Gi2/0/2
show logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
we hava a couple of 2960 switches and we are logging to a syslog server. Ports keep going up and down is it normal severity (error) ?
View 2 Replies View RelatedNew to Cisco and want to know if I can segment a port. I have two v lans. I have one internet connection at the opposite end of the building. Can the port the internet is connected to serve both V lans?
View 6 Replies View Relatedit is possible to let cat3750 or 2960 ports which only allow machine on network which it use dhcp, not static ip? if so, how to configure it?
View 8 Replies View RelatedI have an doubt about some port in 2960.He have 2 SFP and 2 Fixed Ethernet. Can I use these 4 ports in the same time? Use 2 Ethernet and the 2 SFP with Fiber?
View 2 Replies View RelatedI have two questions for a Cisco 2960 (WS-C2960-24TC-L)
1. I am working to setup a few Cisco 2960 switches for HP iLO access to our servers. We are going to segregate the iLO network (VLAN 40) from the data network (VLAN 10) by using a different VLAN. All of the HP servers will be configured with static addresses. My question is, how do I set all the ports to VLAN 40 so that untagged devices will automatically go onto VLAN 40? I don't want to have to configure the VLAN on each iLO port on the server. I tried to set the port to: "switchport trunk native vlan 40", but that didn't work.
2. Also, how do you access the web GUI for these switches? I get a login box, but putting in the enable password doesn't work. I have the following commands in the config: [code]
We have a 2960 switch which is connected to the core via a VLAN trunk. We have disabled broadcast port suppression but, the 2960 is shutting is shutting 2 ports down on the network and this looks like excessive braodcast. How and why would the switch start dropping traffic when the default is don't do anything? It had to be rebooted to get the port active again
View 1 Replies View RelatedDisable ports looping Users connect the network cable at two points in the network generating looping. which command to disable two ports of a Cisco 2960 when they are connected at the same time with the same network cable?
View 2 Replies View RelatedI've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies View RelatedWe have around a dozen Catalyst 3560 and 2960 switches in a ring topology. We are considering adding storm control to our trunk ports. Up until now we have only used it on edge ports with default values and without error-disable.I am proposing that we also add storm control to trunk ports at a lower level and that we error-disable only the redundant links that make up our loops.
-storm-control broadcast level 25.00 20.00
-storm-control multicast level 2.00 1.00
-storm-control action shutdown [only on redundant links]
In a storm all links will restrict broadcast which should work accessing remote switches, but the redundant links should errdisable and block the redundant path. It is important that the action line is not applied to links that are not redundant as we could isolate parts of the network. Any reason not to use storm control on trunks?
I have been experiencing discards and no buffers errors on my 2950 switches. These switches are connected to two core switches 4948 and 3560G. I have noticed previous posts regrading these problems but have been unable to find any cases that were resolved. We are using 12.1(22)EA11 software on our 2950 switches.
Outputs:
flrnet3#SH controllers ethernet-controller gigabitEthernet 0/2
Transmit Receive 22204993 Bytes 904542488 Bytes
[Code]....
As per the attached diagram: How do I configure the 2 ports on the 3560 (Ports 6 & 7) and the connected ports on each of the 2960 switches (Port 25) to provide redundancy.
If the up link from Switch A dies then I need the traffic to flow through the trunk and utilize the up link on Switch B with minimal delay (milliseconds).
I have a Cisco Catalyst 2960 series switch. When I connect another switch or a VMWare Esx server on one of the ports, the port blinks for few seconds and then goes off. When I connect a desktop or laptop or a windows server the ports stay led and I can access resources on the network. However, when connect another switch or a vmware esx server, the port is disabled.
What config in the switch can I check to make sure the ports stay on regardless when I connect a desktop / laptop, switch or vmware server?
I would like to save power by scheduling the PoE switch ports on my switches to shutdown every night and turn on at a specified time during day.
View 6 Replies View RelatedI have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedI'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies View RelatedI am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies View Relatedi try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
I am setting up a new 2960-S switch and none of the recommended username and passwords combinations work. I have tried CIsco Cisco, <blank> cisco and various other permutations.
I have tried to reset the switch to factory defaults and it still doesn't work. The switch is currently connected to a 3560G and has been assigned an IP. If I try to access it from Network assistant it shows as unmanaged and I get prompted for a username and password.The switch is connected to another new 2960-S via a FlowStack module.
I like the SG-300 switches for SMB and I'd like use them in our network. Design is quite simple just 6 SG-300 switches connected to one central switch using SFP ports (using 2 port trunks) so I need 12 SFP ports and this is my question. Could you recomend me switch with more then 12 SFP ports from Cisco for this SMB network ? I don't know all the Cisco product lines and I can't find it.
View 2 Replies View RelatedI need to know the 172cisco 1 router support to IPv6 & it support to IPv6 then which IOS is required for it.Also I need to know the cisco 2960 switch is support to IPv6?
View 3 Replies View RelatedCurrently Being Moderated password recovery
View 3 Replies View Related