Cisco Switching/Routing :: 4500 / Flapping Between Ports?
Jun 27, 2012
We have been receiving these notifications on one of our core.
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host b407.f9c3.3c51 in vlan 56 is flapping between port Po5 and port Te7/2
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 145a.05c8.0ed3 in vlan 802 is flapping between port Te7/2 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 9463.d129.546a in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 3c43.8ef3.7448 in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 000e.35eb.25ae in vlan 66 is flapping between port Po5 and port Te7/2
PO5 goes to our primary wireless controller. Gi2/9 goes to a Cisco 4500 switch that also has a PO5 on it for a failover lan controller and TE7/2 is another core switch.
These mac-address all seem to point to PO 5 which is the port channel assigned to Wireless Controller interfaces.
How do I determine if this is a spanning-tree loop? No ports are err-disabled.
View 8 Replies
ADVERTISEMENT
Dec 6, 2012
Two days back my entire network was behaving in unusual ways.When is connect to core switc(4506e) through console. [code]
View 11 Replies
View Related
Feb 4, 2013
I have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
View 1 Replies
View Related
Aug 27, 2012
I am receiving the following error message on a Cisco 3750 switch stack. Need troubleshooting this error message.
00:03:13: %SW_MATM-4-MACFLAP_NOTIF: Host 00d0.7400.2730 in vlan 600 is flapping between port Gi2/0/3 and port Gi2/0/2
View 3 Replies
View Related
May 23, 2012
How i can configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.
View 4 Replies
View Related
May 20, 2012
I have installed a WS-X4448-GB-RJ45 on a 4503 chasis. I could not get input or output rate, just shows 0 bit/seg wether or not is forwarding traffic. I would like to know if I have to make any configuration or workaround. The IOS version is 12.2(37)SG1.
View 1 Replies
View Related
Feb 24, 2013
I have a Cisco 4500. Recently some of the ports seem to have "died"/ will not supply Poe to phones. Some work for data only. Other do not work at all. The switch has been restarted, this made no difference.
View 2 Replies
View Related
Apr 24, 2012
I was checking some things on my Cisco 4500 and spot checking some of the ports. Using CNA it says it is at 10. The web browser to the switch says Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000-TX on port 6i/18 The CNA says, so what would cause the difference?
View 3 Replies
View Related
Dec 15, 2011
I know in the past on earlier models of the supervisors that you couldn't use all eight uplink ports(4 on each supervisor) simultaneously when you have two supervisors on the chassis. Is this the same case for the 10Gb uplinks on the supervisor 7-E on the 4500 chassis? I tried doing my research but couldn't find an answer.
View 3 Replies
View Related
Oct 31, 2011
we have a 4510r-e running 12.2(50)SG1 w/ various rj45 line cards and a 24 port glc card.at any given time, i see 10's of ports in 10/full.i go to the station, and find the station in 100/full or 1000/full.
i go to the switch w/ my fluke, connect it directly to the switch w/o any intermediate infrastructure except a 50cm cat6 patch cable.the fluke reports 1000/full, but THE SWITCH PORT REPORTS STILL 10/FULL.all ports are config'd 'speed auto' and 'duplex auto'.
the switch seems to be erroneously reporting 10/full.there are no errors logged on any of the ports and there is successful communications even when the station and switch port report different speeds.even though there are no errors logged nor reported by 'show int [port]' nor 'sho int count error' certain killer applications crash on some stations. (the applications are GHOST (which dumps disk images from a server to multiple stations) and NETOP (which i sused in a classroom to transmit an instructors screen to a room full of stations) both of which broadcast and/or multicast.all nodes involved in the above 2 applics are on the same vlan and same phyiscal subnet.
the ports which report 10/full vary and occur even when the above applics are not in use.the only way i found to clear this 10/full report is by either a hardware reset of the entire module or by unplugging the cable, the execute on the port shutdown, speed auto, no shutdown, reconnect cable.then it's just a matter of time until it pops back to 10/full in a few minutes,hours or days.
how to address the killer applic problems besides restructuring the whole net by defining separate vlan for each lab of 20 or so stations?
View 7 Replies
View Related
Sep 22, 2011
I recently upgraded my network to have two 3750x core, one interface on the cisco is connecting to a Netgear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
View 2 Replies
View Related
Jul 9, 2012
i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
[Code]......
View 2 Replies
View Related
Apr 14, 2013
i have a question, i have in the logging of my switches a mac falpping problem. i have a log notification : Apr 12 19:33:13: %SW_MATM-4-MACFLAP_NOTIF: Host xxxx.f065.520c in vlan 25 is flapping between port Gi0/1 and port Fa0/35. When i look up what is connected to interface FA0/35 it is a accespoint " AIR-AP1242G-A-K9" Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
How this is making the mac flapping ?
View 2 Replies
View Related
Jun 4, 2012
We have some legacy Cisco 6513 switches with the backbone (16-port GBIC blade) MTU set to 1500. It has a WS-X6148A-GE-TX blade as well, MTU set to 9K.
Now we have a customer sending MTU of 1546, their copper interface terminating on WS-6148A keeps flapping. Does the flapping have something to do with the backbone set to 1500? We cant set the backbone to 9K at this moment since it may be intrusive (reuire a reboot).
View 1 Replies
View Related
Feb 27, 2012
We have two switches WS-C2960S-24TS-L running in stack with running IOS c2960s-universalk9-mz.122-55.SE3.We have connected two checkpoint devices on Gi1/0/24 and Gi2/0/24 with a simple configuration:
interface range GigabitEthernet1/0/24, gi2/0/24
switchport access vlan x
switchport mode access
spanning-tree portfast
On the devices log we get the following message:
%SW_MATM-4-MACFLAP_NOTIF: Host 0000.0000.fe21 in vlan x is flapping between port Gi2/0/24 and port Gi1/0/24
The mac-address 0000.0000.fe21 is not found on any checkpoint interface. "Show mac-address int gi1/0/24 or gi2/0/24" does not show the correct mac-address of the checkpoint interface connected to the port, but instead shows 0000.0000.fe21.Is there a bug in the IOS, something wrong with the switch config or does it have something to do with the checkpoint config?
View 2 Replies
View Related
Nov 15, 2011
This is the message that I am getting from my 1941w router. I have a isakmp tunnel built with a GRE tunnel going through it.
View 15 Replies
View Related
Mar 28, 2013
Lately I have been noticing mac flap messages on some of our access layer 3750G switches. Just a little background on how this is setup.
These 3750G switches are stacked and uplinked to a distribution layer 3750E stack (2 switches) via cross stacked etherchannel. (Usually 4 links) The access layer switches are stricly layer 2 where the distribution layer 3750E is routing the VLANs at the access layer to to the core 6500 switches.
I have just about ruled out physical loops on these stacks for the reason that the Macs are flapping. I am seeing this on two different stacks now each having 3 switches in the stack at the access layer. The cross stack etherchannel is spanned across the first two switches at the access layer and connected to both switches at the distribution layer. I have checked the etherchannel status and all ports appear to be part of the etherchannel and they appear fine.
The mac addressses that are flapping are just plain old desktop machines that plug directly into the access layer. I usually see this when the mac is learned on a port such as when a machine is plugged into the network or reboots.
View 6 Replies
View Related
Mar 5, 2013
Would like to ask whats the correct snmp config so that it will send to our snmp server when a mac flapping occurs on a cisco switch specifically 4507 switches.
View 6 Replies
View Related
Aug 27, 2012
I work for a Wireless ISP and the device impacted is the back haul radio into the site. I have swapped from a 2950T to a 3550. Replaced the radio, PoE, patch lead. We have re ran the cable up the tower using shielded outdoor cable with a drain wire which has been earthed to an earthing block in the cabinet. We have other devices on the tower not experiencing the issue. We suspect cable interference however am now at a loss to diagnose further.
[Code]....
View 3 Replies
View Related
Mar 10, 2012
We have a pair Cisco 6509 switch in which 2 * 48 Port 1G line cards and 1 * 16 Port 10G line Card, FWSM and Sup 720 are installed.We have Cisco UCS and HP Blade servers.Cisco UCS servers are connected to Cisco 6509 switch using Fabric Interconnect, and HP Servers are directly connected to core switches.Recently the team made many changes in the network. Upgraded the IOS in Cisco 6509 switch, Configured Port profiling , MAC Pinning , HBA Cards to UCS / Nexus 1000V Infrastructure. After this change they lost the connectivity to UCS and HP Serers. Every tower is checking at their end.
The Network Team has reverted back the core switch with old IOS , but still the problem persisit.I could only see the following error log in the core switch. There are two port-channels one between core 1 and core 2. The other is between core switch and FWSM module. [code]
View 2 Replies
View Related
Jul 23, 2012
we have cisco 2960 switch which is connected to a cisco 2811 router. flapping issue between these two devices??
The following actions i have taken, but no result.. I have changed cables. have set speed to 100 and duplex full on both the interfaces but the interfaces are showing up up still not getting connectivity. same i have to auto on both sides still no result what configurations should i set to resolve this issue...?
View 10 Replies
View Related
Oct 2, 2012
I have Cisco 1811 and Cisco 2960 interconnect with each other by TRUNK link. As time pass i recieving below log on cisco 1811 router.
DTP-5-NONTRUNKPORTON: Port Fa8 has become non-trunk
LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne t8, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan200, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan300, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan400, changed state to down
View 4 Replies
View Related
Sep 15, 2012
I recently upgraded my network to have two 3750x core, one interface on the Cisco is connecting to a Net gear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
003396: Sep 17 01:46:16.328: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003397: Sep 17 01:46:19.843: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003400: Sep 17 01:49:58.769: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/17, changed state to down
[Code] .....
After my research i think this is a looping issue but I'm unsure how to address it.
View 2 Replies
View Related
Jun 2, 2013
i just configured a C6K VSS with Sup2T, 15.1SY IOS software and a WS6724-SFP module with the follwing cos config:
auto qos default
table-map cos-discard-class-map
map from 0 to 0
map from 1 to 8
map from 2 to 16
[code]....
After applying the service policy to one interfac of the WS6724-SFP module the policy is deployed to all interfaces of the module. So far it should be ok but after a short time all interface of the module begin to go down an up and down and up ... flapping.
View 1 Replies
View Related
Feb 22, 2012
Stange problem which I encountered today, I have a Cisco 2960 which is connected to a netgear. The switch started showing itself in CDP and was running STP. I checked the cables physically today and noted 3 uplinks to the netgear, all port on the Cisco active and forwarding and green lights.
The Cisco was running STP, I changed it to R-PVST and the lights on the Cisco went crazy and I got the message port flapping on the switch but the switch did not block any ports (all ports on same vlan).
There after I changed it back to stp and the switch blocked the other up links apart from one.
Sure R-PVST is far superior than STP?
View 5 Replies
View Related
Sep 11, 2012
I have two Core 6509E SUP2T configued as VSS and has two 48 ports fiber blades. I have two 3750s, I have two gig on each 3750 port-channle to po1 and connected to both the core, one link to each core.Now, I was asked ot add two more links on each 3750 switch to make it a total of 4 gigs on each 3750s (all 4 gig ports/uplinks will be in used an dtwo links to core one an dtwo links to core 2).when i added two additional links on 3750s and bundled them to po1, I created another port channel on core and bundeled the additional two gigs on each core to accomodate for the two additional links (ports on core switches are not consequtives).
adding these two additional ports makes the 3750 switches flap between managemnet vlan and po1.now, i am not sure if I must have added the two additional links on the core to teh current port-channel or core!? I have created another port-channel on core to accomodate for this currently!?
View 26 Replies
View Related
Mar 11, 2012
I have an issue with a Cisco 3750 switch stack which is connected to two seperate upstream Cisco 3750's which are administered by an ISP. The ISP is experiencing MAC address flapping from one of my VLAN SVI's i am using to route traffic upstream
[code]...
As you can see I utilise a VLAN SVI to route traffic to the upstream 1.1.1.2 (illustration only) IP. As per the diagram of the topology attached, the ISP is receiving a MAC address flapping error confirming the SVI MAC address from my switch stack is being learnt on the trunk port connecting switch 1 and switch 2, and also the port (Gi1/0/48) directly connected to my switch stack. As these are all Layer 2 links essentially being passed upstream and then connected between the two ISP switches, we have a 3 way triangular loop formed.
If I was to remove the port channel configuration from the two ports associated with the VLAN SVI, am i right in suggesting this would still form a layer 2 loop? The two ports would still be a member of the SVI VLAN, and it is the VLAN MAC address which is being learnt by the two ISP switches on different interfaces.
View 2 Replies
View Related
Apr 30, 2012
show logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
View 2 Replies
View Related
Mar 6, 2013
I need to know if Catalyst 4500-X does PBR in hardware?
View 1 Replies
View Related
Feb 28, 2012
Does the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies
View Related
Apr 3, 2013
question on 4500 SUP-7LE, this documentation is not 100% clear:
[URL]
When in single sup mode, can I have the following combinations?
1 SFP+ and 1 SFP << pretty sure this is supported
1 SFP+ and 2 SFP << think it's supported
1 SFP+ and 3 SFP << doubtful
2 SFP+ and 2 SFP << think it's supported
3 SFP+ and 1 SFP << doubtful
View 1 Replies
View Related
Nov 16, 2009
I'm seeing the following error on a 4500 running 12.2(46)SG
C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Module 5 inline power exceeds threshold: status changed to 'Pwr Over'
All the ports on module 5 have "power inline never" applied, in fact the whole switch has POE disabled.
I've attached a txt file with the show power detail output.
View 2 Replies
View Related
Apr 22, 2013
How to know 4500 SUP7-E's MIB ?Our customer use MS SCOM 2012 SP1 get the OID are 1.3.6.1.4.1.9.1.1286, but we use IOS MIB locator, we can not find this MIB id.
below are the IOS sh version information :
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 26-Apr-11 18:09 by prod_rel_team
[code]....
View 2 Replies
View Related
