Cisco Switching/Routing :: 6509E Port-channel Flapping When Two More Links Are Added?

Sep 11, 2012

I have two Core 6509E SUP2T configued as VSS and has two 48 ports fiber blades. I have two 3750s, I have two gig on each 3750 port-channle to po1 and connected to both the core, one link to each core.Now, I was asked ot add two more links on each 3750 switch to make it a total of 4 gigs on each 3750s (all 4 gig ports/uplinks will be in used an dtwo links to core one an dtwo links to core 2).when i added two additional links on 3750s and bundled them to po1, I created another port channel on core and bundeled the additional two gigs on each core to accomodate for the two additional links (ports on core switches are not consequtives).
 
adding these two additional ports makes the 3750 switches flap between managemnet vlan and po1.now, i am not sure if I must have added the two additional links on the core to teh current port-channel or core!? I have created another port-channel on core to accomodate for this currently!?

View 26 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Standby Blade Switch 3030 Upstream Port-channel Flapping Up-down

Apr 30, 2012

show logging

May  1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May  1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May  1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May  1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May  1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May  1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May  1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
  
Configuration as below:

macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan

[code].....

Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.

View 2 Replies View Related

Cisco Switching/Routing :: Stack 3750X - How To Configure Port Channel To Aggregate Two Links

Feb 18, 2013

I have two stacks 3750X on two different sites with two links L_2_L, and I want to configure the port channel to aggregate the two links.
 
Site A                                                                                                  Site B
3750X -A1 --------------------------------------(          )--------------------------------------- 3750X -B1
                                                      (  L-2-L )
3750X -A2 --------------------------------------(          )--------------------------------------- 3750X -B2

Below the configuration that I have put the two stacks.
 
site A
interface Port-channel5
description Etherchannel group entre le stack 3750X-A et Switch Lan_2_Lan
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 11,12,999
switchport mode trunk
switchport nonegotiate
speed 100
 
But the problem is only one link is Bundeled in channel group, see below

Group  Port-channel  Protocol    Ports
------+-------------+-----------+-----------------------------------------------
5      Po5(SU)         LACP      Gi1/0/15(I) Gi2/0/15(P)

View 8 Replies View Related

Cisco Wireless :: 5508 / WLC Port Channel Host Flapping

Oct 9, 2011

I have setup LAG for one of our 5508 controllers and have connected 4 of the 8 ethernet ports to a 4507 switch. After configuring 2 port channels on the switch we are receiving a host flapping error between the port channels and it seems to be causing a serious slowdown on the switch. When I shutdown one of the port channels the error goes away and traffic returns to normal. I have the same configuration at other locations with the only difference being the switches used are 3750G-12S and I do not see the host flapping error. It appears to only be a problem with modular switches.
 
One other thing of note: I read a Cisco white paper on LAG and it suggested creating the port channels over 2 different modules. For example, put ports G4/24 and G5/24 in port channel 1 and G4/25 and G5/25 in port channel 2. I tried this but I still got the host flapping error.

View 4 Replies View Related

Cisco Firewall :: 6509E / FWSM Default Port Channel?

Jan 22, 2012

I'm doing some L2 cleanups across mutliple 6509E environments and I've found something consistent that I can't find in documentation. On all my pairs of 6509s where I have FWSMs bundled (6509-A has FWSM-1 is Slot 1 and 6509-B has FWSM-2 in Slot 1) I also have a port channel 305. Obviously when I do a "show run" or "show int desc" I don't see anything in slot one. It's a service module. But the port channel is referencing ports 1/1-6. And it's all in service/up. I was about to delete this as I thought it was some leftover config (TEST 6509s) until I went and saw the same things on our PROD 6509s. Is it cosmetic? Necessary? Can I delete it as part of my audit cleanup? Don't want to mess with it even in TEST without some information. Nothing on google that's clear and I can't find anything on CCO.
 
#################################################################################
6509-1#sho etherch 305 summ
Flags:  D - down        P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)

[code]....

View 1 Replies View Related

Cisco Switching/Routing ::1002 Layer 3 Ether-channel Vs Two Separate Links

May 19, 2013

We were going to create a 2 port, layer 3 etherchannel between a 1002 router and a 3750X layer 3 core switch. We wanted to create bunled link between them but, now we are going to be putting a Riverbed device between the router and core switch. Because of this, would it be best to abandon the idea of creating a layer 3 etherchannel and just have 2 links from the router and core switch and have traffic load balance between the 2 links?The Riverbed will have 2 connections into it from the Core switch and 2 connections into it from the 1002 router. I was hoping to keep the layer 3 etherchannel but, do you think it would be best to create 2, /29 nets and have the router/Riverbed and Core Switch/Riverbed load balance.

View 5 Replies View Related

Cisco Switching/Routing :: 3750-48 Port Switch - IP Route Added Not Showing Up

May 30, 2013

We have a cisco 3750-48 port switch.We have a few SVI's configured and some static routes configured.I had created a new interface vlan and gave it an IP. I can ping the gateway.
 
Now I want to add a static route to go out that interface.when I add: ip route 10.x.x.x 255.255.255.0 10.52.10.1
 
it eccepts it (no errors) But, it does not show in the routing table nor in the config? How to add the static route to go out that vlan interface.

View 15 Replies View Related

Cisco Switching/Routing :: WS-6148A - Port Flapping Due To MTU Mismatch?

Jun 4, 2012

We have some legacy Cisco 6513 switches with the backbone (16-port GBIC blade) MTU set to 1500.  It has a WS-X6148A-GE-TX blade as well, MTU set to 9K.
 
Now we have a customer sending MTU of 1546, their copper interface terminating on WS-6148A keeps flapping.  Does the flapping have something to do with the backbone set to 1500?  We cant set the backbone to 9K at this moment since it may be intrusive (reuire a reboot).

View 1 Replies View Related

Cisco Switching/Routing :: 6509E - Four Port 10G Blade Buffers 16M

Dec 29, 2011

Looking at the specs for WS-X6704-10GE, it shows the port buffers at 16M per port. This doesn't seem like very much for a 10G port. Is this upgradable or related to how much RAM is in the blade?

View 4 Replies View Related

Cisco Switching/Routing :: Nexus 7000 Vlans Added To Port-profile Never Got Propagated

Dec 2, 2011

I'm running a couple of nexus 7000 to aggregate a building full of 3750Xs.In the past few weeks I have noticed that the vlans I added to the port-profile never got propagated.So I looked at port-profile sync information and here is what comes up: [code] Why the commands are getting cached?

View 3 Replies View Related

Cisco Switching/Routing :: 3560 - What Happens When Voice Vlan Command Is Added To Trunk Port

Oct 11, 2010

Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
 
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.

View 8 Replies View Related

Cisco Switching/Routing :: 6509 Vlan Flapping Between Port-channels

Mar 10, 2012

We have a pair Cisco 6509 switch in which 2 * 48 Port 1G line cards and 1 * 16 Port 10G line Card, FWSM and Sup 720 are installed.We have Cisco UCS and HP Blade servers.Cisco UCS servers are connected to Cisco 6509 switch using Fabric Interconnect, and HP Servers are directly connected to core switches.Recently the team made many changes in the network. Upgraded the IOS in Cisco 6509 switch, Configured Port profiling , MAC Pinning , HBA Cards to UCS / Nexus 1000V Infrastructure. After this change they lost the connectivity to UCS and HP Serers. Every tower is checking at their end.
 
The Network Team has reverted back the core switch with old IOS , but still the problem persisit.I could only see the following error log in the core switch. There are two port-channels one between core 1 and core 2. The other is between core switch and FWSM module. [code]

View 2 Replies View Related

Cisco Switching/Routing :: 2690 / 1811 - Port Flapping With Log DTP-5-Nontrunkporton

Oct 2, 2012

I have Cisco 1811 and Cisco 2960 interconnect with each other by TRUNK link. As time pass i recieving below log on cisco 1811 router.
 
DTP-5-NONTRUNKPORTON: Port Fa8 has become non-trunk
LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne t8, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan200, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan300, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan400, changed state to down

View 4 Replies View Related

Cisco Switching/Routing :: Total Output Drops On Switch Port On 6509E

May 22, 2012

What is the cause of having a huge number ( 875349) of total output drops on one of my gigabit utp port  gi 2/12 which is connected to Cisco 1841 fa0/0 router by mean of cat5e cable.I did change the cable from cat5e to cat 6 and tried to increase hold queue to 4096 and to tweak wrr queue bandwidth

View 4 Replies View Related

Cisco Switching/Routing :: 6509E / SUP720 (Standby Hot) - Console Port Indicate Software Crash

Oct 28, 2012

I have one Catalyst 6509E chassis and two SUP720. The bootup sequence  on SUP 720 (standby hot) failed . Messages that appear on SUP 720, on the console port indicate o software crash.  I don't have a flash card in SUP720. 
 
This is the bootup process:
 
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory

[code].....

View 1 Replies View Related

Cisco Switching/Routing :: Will All 4-ports Of N5K Will Be Same Port-channel

Sep 12, 2012

Have 2 N2K with dual-connections to both 2 N5K, will all 4-ports of N5K will be the same port-channel. N2K as well ?

View 1 Replies View Related

Cisco Switching/Routing :: Port-Channel Between 4507

Nov 29, 2011

I need to configure a port channel between two sw 4507R. with port Giga, but those port are in different modules.
  
Sw-1
interface GigabitEthernet5/48
description **** Conexion Switch-2*****

[Code].....

View 2 Replies View Related

Cisco Switching/Routing :: 3750 As A Port Channel Bridge?

Dec 7, 2011

I have 3750 core/distribution switches with routing enabled in two offices connected with copper link and L3 port channel interfaces. NewOffice#2 has moved about 5 miles farther away from office#1 and I have to deploy new core/distribution switch connect it to old core#2 via F.O and move all access switches with it. Old core will stay in old #2 offices as a bridge between office#1 and new office#2 Office#1core<->copper (Ethernet) <->oldoffice#2core<->f.o. <->new office#2core How I should configure port channels ports on oldoffice#2 core to act as bridge between office#1 core/dist and newoffice#2 core/dist without changing anything else (ip, etc) on whole network

View 1 Replies View Related

Cisco Switching/Routing :: 6509 Trunk To Port Channel

Apr 22, 2012

I have 2 Cisco 6509 switches linked together via single Fibre as a trunk.I want to change this to a port channel where I will add another 3 fibre ports to the port channel but what order do I do this to minimise any disruption.

1-Configure PortChannel and add the 3 new ports, this will bring up the Port Channel but what effect will this have on traffic currently going over the single Trunk link? Will spanning tree go mad, how will switches react?

2-Convert existing Trunk link to Portchannel then add in new ports to PortChannel, I guess in doing this there will be a small hit on traffic as it changes to a port channel.

View 2 Replies View Related

Cisco Switching/Routing :: Lost Port Channel Between 6513

Feb 24, 2012

We have 2 6513's that are linked via 2 10 gig interfaces, using an LACP channel.I received an alert this aft stating that the far 6513 was unreachable and the port channel int PO3 had gone down, the 2 10 gig interfaces had also gone down on either side. 5 mins later PO3 had resestablished itself and has been fine since. [code]

View 4 Replies View Related

Cisco Switching/Routing :: Nexus 5018 / Port Channel Down?

Feb 7, 2013

We are running nexus 5018 in our DC.What is the difference betwen "channel-group 214 mode active"  and " channel-group 216" Any difference?.. because i have problem with this config we are going build a server config? 
 
We have problem with porth channel down.
 
5K# sh int po71
port-channel71 is down (No operational members)
vPC Status: Down, vPC number: 71 [packets forwarded via vPC peer-link]

View 1 Replies View Related

Cisco Switching/Routing :: 3750 - How To Setup Port-channel

Jan 22, 2012

I set up a port-channel trunk between a acess switch 3750 ( int gi2/0/1 and gi2/0/2) and Core 6509( int gi7/11 and gi7/12).
 
On the both the 3750& 6509 I configured:
 
interface Port-channel15
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 100,103
switchport mode trunk
 
But the ports on the core g7/11 and g7/12 keep shutdown and when I do show interfaces port-channel 15, it show the interface is shutdown.

View 6 Replies View Related

Cisco Switching/Routing :: Min-Link Configuration On 3750-X Port-channel

Feb 27, 2013

I am building a new network and intended on using the min-link feature on my port-channels between a 3750-X series switch and Nexus 4k.

However reading further into this it seems this feature is only supported on higher end models. I cannot find any reference to the min-links feature in the 3750-X configuration guide. Is this an available feature?

The 3750-X model is WS-C3750X-24T-L running IOS 12.2(55)SE3 IP Services

My thoughts is that the is only an LACP supported feature so I may not see the command until I have entered an LACP specific command on the port-channel but unfortunately I do not have a 3750X to verify this on at present.

View 0 Replies View Related

Cisco Switching/Routing :: Can Port Channel In 3825 Connect To Two Different Switches

Jan 17, 2012

We have one 3825 router used as voice gateway. For redudancy, we want to connect it to two different switches which has STP and HSRP running. Can I create a port-channel with two Giga interfaces in 3825 and connect to two different switches? Should I configure port channel in switch with only one port in each port-channel? I know server can be connected to different switches with NIC teaming. I just want to mimic that kind of setup. I did one time for port-channel in 3825, but it was connected to a stacked 3750X. So it's different case now.

View 2 Replies View Related

Cisco Switching/Routing :: ME380x Port-channel From One Switch To Two Switches

May 8, 2013

I am trying to configure port-channel from one switch to two switchs, and only one interface of each switches make part of the port channel.Cisco IOS Software, ME380x Software (ME380x-UNIVERSALK9-M), Version 12.2(52)EY4, RELEASE SOFTWARE (fc1) [code]

View 5 Replies View Related

Cisco Switching/Routing :: 6500 Setup In VSS Configuration - Port Channel ID

Jan 22, 2012

I have a pair of 6500's setup with VSS and there is currently only one link between then. However one end of the link is on Po10 and the other end is on Po25.  If I move the Po25 over to Po10, will things break? It seems to be working fine now. I'm about to add a second link and I'm concerned about the current configuration.  It makes more sense to me to have both ends of the same link on the same port-channel ID.  I've seen documentation which states otherwise however.
 
interface Port-channel10
no switchport
no ip address

[Code]....

View 2 Replies View Related

Cisco Switching/Routing :: 3560 / Allowing Etherchannel Or Port Channel?

Mar 3, 2012

I am using 3560.IP rouitng is being turned off on this.Curious to know if I will create etherchannel or port channel.I think etherchannel.Correct me if I am wrong.On connecting switches I have vlan10,20,30 to be allowed.I am sure I need to allow these all vlan in 10,20,30 which are on the trunk port on each side switch.Post that will add channel-port lacp and make it in active mode.Is that correct.This way traffic will be load-balanced/aggregated on minimum 2 ports who are the part of this.

View 2 Replies View Related

Cisco Switching/Routing :: 3750s Port Channel Between Server And 2 Different Switches

Jan 27, 2013

Here's what I'm trying to do.  We are having new storage servers installed that will be using NFS.  I'm being told that they need to have their connections port channeled.  Right now, the servers have connections to 2 different 3750s for HA. Is it possible to configure a port channel between these 2 connections?

View 4 Replies View Related

Cisco Switching/Routing :: C2960 - Port Channel Load Balancing?

Apr 15, 2013

I have an inquiry about a configuration I deploy in a C2960 switch. I have configured a ether channel with 8 ports, the load balanced method is source mac address. The bundling protocol is LACP.
 
I have found the ether channel is not balanced as I expect. One of the eight interfaces is congested.
 
Code...

View 2 Replies View Related

Cisco Switching/Routing :: Auto Qos Dropping Port Channel In 3750?

May 13, 2012

We have a switch that, when configuring auto qos on and edge port facing video equipment, the upstream port channel drops. I was wondering if no auto qos would have to be configured on the member ports of the port channel prior to enabling auto qos on any other ports. 

View 2 Replies View Related

Cisco Switching/Routing :: 6500 Redundant Supervisor Port Channel?

Oct 30, 2011

I have a Cisco 6500 series switch with VS-C6509E-S720-10G ,I have two redundant supervisors between two chassis on the LAN with no add-on line cards ?

I need to know if I can use the redundant supervisor 10 Gb uplinks to form a layer-2 Port channel between the two 6500 switches as i do not want to use want to keep the port idle additionally I need more bandwidth between the two switches for my server farm?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 STP Config On Port-channel Best Practice

Apr 3, 2012

I have 2 cisco 6500 in a VSS configuration , All of my Lan access switches are Stack switches and every Stack is connected to the VSS in a Port-channel so basically this is a loop free environment with no blocked ports .As a best practice I left STP in the Background (mstp)which enhanced cisco features to STP should I configure on the Aggregator (6500-VSS) and on the Access switches ?
 
Because of my topology I dont see the need in configuring most features like Uplink Fast and Backbone Fast but I have configured Loop Guard in addition to UDLD on the 6500 Aggregation Switches (on the port-channels).On the access ports I have configured portfast , bpduguard and guard root (seems a little pointless to configure the two...)
 
1.should I Leave UDLD on and get rid of LoopGuard and configure Guard root instead ? since LoopGuard cannot be configured with Guard Root.
 
2.should I configure GuardRoot on access ports if I already have BpduGuard on them ?
 
3.Is there anything I need to configure on the physicall interface or is everything configured on the port-channel since STP reguards port- channel as a single interface ?

View 4 Replies View Related

Cisco Switching/Routing :: Create A Port Channel Between HP Servers (4 Nic) And Two Nexus 2k?

May 9, 2012

I am trying to create a port channel between HP servers (4 nic) and two nexus 2k.  The server side its a single team with 803.2ad fault taulerence and on the nexus side it have created two port channel (port channel 1 for nexus 2k1 and port channel 2 for nexus 2k2) and made them ACTIVE (channel group mode active)
  
But when i add a another server on different ports and port channel them the same way as the above server on nexus 2k1 and nexus 2k2, the first server stops pinging. so i have to sht down the first port channel and reopen them - then it works, however it says NO NETWORK ACCESS on the servers (running windows 2008). the only way is to reboot the server  i cant be doing this on a production network.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved