Cisco Switching/Routing :: 4500 Switch Reports Ports As 10 / Full While Other Side Reports 100
Oct 31, 2011
we have a 4510r-e running 12.2(50)SG1 w/ various rj45 line cards and a 24 port glc card.at any given time, i see 10's of ports in 10/full.i go to the station, and find the station in 100/full or 1000/full.
i go to the switch w/ my fluke, connect it directly to the switch w/o any intermediate infrastructure except a 50cm cat6 patch cable.the fluke reports 1000/full, but THE SWITCH PORT REPORTS STILL 10/FULL.all ports are config'd 'speed auto' and 'duplex auto'.
the switch seems to be erroneously reporting 10/full.there are no errors logged on any of the ports and there is successful communications even when the station and switch port report different speeds.even though there are no errors logged nor reported by 'show int [port]' nor 'sho int count error' certain killer applications crash on some stations. (the applications are GHOST (which dumps disk images from a server to multiple stations) and NETOP (which i sused in a classroom to transmit an instructors screen to a room full of stations) both of which broadcast and/or multicast.all nodes involved in the above 2 applics are on the same vlan and same phyiscal subnet.
the ports which report 10/full vary and occur even when the above applics are not in use.the only way i found to clear this 10/full report is by either a hardware reset of the entire module or by unplugging the cable, the execute on the port shutdown, speed auto, no shutdown, reconnect cable.then it's just a matter of time until it pops back to 10/full in a few minutes,hours or days.
how to address the killer applic problems besides restructuring the whole net by defining separate vlan for each lab of 20 or so stations?
View 7 Replies
ADVERTISEMENT
Dec 21, 2011
I have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T. I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials. If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg. I have 6 cat-e ethernet cords everywhere. I do have 2 switches but have tried to unplug those to see if any difference
View 1 Replies
View Related
Feb 24, 2013
I have a Cisco 4500. Recently some of the ports seem to have "died"/ will not supply Poe to phones. Some work for data only. Other do not work at all. The switch has been restarted, this made no difference.
View 2 Replies
View Related
Apr 24, 2012
I was checking some things on my Cisco 4500 and spot checking some of the ports. Using CNA it says it is at 10. The web browser to the switch says Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000-TX on port 6i/18 The CNA says, so what would cause the difference?
View 3 Replies
View Related
Oct 24, 2011
We are running WCS 7.0.1 and ACS 4.2 using TACACS for our techs to login to WCS (to manage access points). However, when the tech trys to run reports, they get an error:
Permissions Denied
The user is setup in Active Directory and not in WCS. I saw something about adding the user to a group in WCS but again the user is setup in AD. Is there something we need to do in ACS? Not sure what do do.
View 1 Replies
View Related
Aug 9, 2011
Have a problem with LMS 4.0.1 and DFM. In DFM no of the devices leaves the questioned state. Trying to rediscover them starts a process that ends after 20% completion every time. I've put on some debuging, but that does not enable more error messages.Only thing i find is in the log file [code] As I've encoded this to be the SNMP engine ID, which on the device is. [code]
View 4 Replies
View Related
Jun 7, 2012
We have CPU reports set to run daily for some of our higher priority switches, and we've noticed that some of the data isn't meshing with what we see on the switch. We have one heavily utilized switch that reports near 100% CPU utilization sometimes. I can do a "show proc cpu history" on that switch and see that at least once an hour over 72 hours, we'll see a near 100% CPU utilization.
The problem is that these spikes never appeare on any of our reports. We'd like to see this info because even if the switch spikes for just a few seconds or a minute, it could still indicate that we may have issues. Without that in the report, we may never realize there could be a problem.
Is there a way for this info to show in the report? I'm under the impression that if LMS polls the switch and doesn't see a high utilization average, then maybe it doesnt' enter that in the report. I guess I'd just like to know how often it pulls this data, and how it decides wath the Min, Max, and Averages are.
View 1 Replies
View Related
Jul 2, 2012
I have modified my radius accounting reports using "interactive viewer" and saved successfully but the exported report doesn't reflect these changes. I'm just wondering what's the point of being able to modify the reports if you can't export your changes or there is something I'm missing?
View 3 Replies
View Related
May 1, 2012
We use LMS 3.2 with the latest patches. In IPM we have a couple of collectors (availabilty latency etc) and reports for our customers.
The polling interval for all collectors are working hour 7:30 - 18:00 Mo - Fr.
Unfortunately the polling detail is not included in the PDF report. Is there a way to include this information in the report.
View 1 Replies
View Related
Apr 3, 2012
We're currently running on ACS 5.2.0.26.9 with 2 appliances (one primary and one secondary).Today, I wanted to get some reports from the Monitoring and Reports tool. At beginning, it seemed impossible to generate them. Later, I decided to reload first primary and then secondary. As soon as I've done it, I got an email alert telling me that it failed parsing NAD.
Cisco Secure ACS - Alarm Notification
Severity: Critical
Alarm Name
System Alarm [Collector]
Cause/Trigger
[code]....
I don't really find where I can find the Collector log...Anyway now when I generate a 30 days report, I only get data up to 23.03.2012. Nothing recent !
View 7 Replies
View Related
Oct 9, 2011
everytime i try to sign into linksys, it reports no internet service or unidentified network
View 1 Replies
View Related
Jun 9, 2013
We had an existing installation of LMS 4.1 which seemed to have worked fine with the exception that it was giving problems with logging Syslog events. We tried everything to resolve it and then we found a link on this very site that explained that there was a bug in displaying Syslog events on LMS 4.1. It is important to state that we would get a few Syslog events but the rest were either filtered or discarded.As per the bug toolkit, we realized that we had to upgrade to LMS 4.2 to have the bug resolved. This was not a problem and we installed LMS 4.2 as a direct upgrade to LMS 4.1. We backed up our existing data and the installation process migrated everythin automatically.Now, LMS 4.2 is installed and our objective of having Syslog messages are being received regularly as we wanted.unfortunately, when we try to generate a report such as "Detailed Device" report and try to select All Devices from the Device Selector menu, we do not see any of our devices. However, we do find our devices listed under User-Defined Groups -> (Our DCR). Based on this, we can generate reports and everything is fine.Yet, we are doing this for a client of ours and they expect to see these devices listed in the "All Devices" section of the device selector. Apart from that, everything seems to be working fine.
View 2 Replies
View Related
Jul 7, 2012
Is there a way I can get the ACS (5.3) to email some of it's reports on a schedule?I'm hoping to send automated summaries of failed logins to the service desk each Monday morning.
View 3 Replies
View Related
Jun 14, 2012
i have a problem that i see the devices by ip not hostname in devices report and topology and i checked in device discovery to appear by hostname
View 2 Replies
View Related
Sep 3, 2011
Though other logs are being received through the email.
View 1 Replies
View Related
Jun 16, 2010
Just installed ACS 5.0.0.21. Monitoring and reports database was working, but now is not. When trying to open, I get "Monitoring and reports database currently unavailable. Trying reconnect in 5 minutes." From CLI "sho application status acs" gives me the following:
ACS role: PRIMARY
Process 'database' runningProcess 'management' runningProcess 'runtime' runningProcess 'adclient' runningProcess 'view-database' runningProcess 'view-collector' runningProcess 'view-jobmanager' runningProcess 'view-alertmanager' running
Also, logs show nothing unusual.
View 6 Replies
View Related
Sep 5, 2011
We have noticed that some devices has dissapeared from HUM pollers and some quick reports have dissapeared too. It happened again some months ago. I would like to know:
1. How I can fix it.
2. Which logs I can see to troubleshoot the problem.
3. If is possible I can restore only the hum module from LMS backup
View 1 Replies
View Related
Feb 21, 2013
Is there a way to configure a favorite report and share it to all all ACS administrators?
View 1 Replies
View Related
Nov 4, 2011
sending emails from simply accounting- I don't have outlook installed on my computer- is there another way to send invoices,reports or emails from Simply Accounting to my customers if I or they don't have outlook installed
View 2 Replies
View Related
Oct 25, 2011
I'm connected to my router via an Ethernet cable, and on the connection icon I have the yellow triangle and a message indicating I have no internet access...but I do. My internet is fully connected and I have no problems remote connecting to my computer from work, downloading and seeding torrents or browsing websites. Problems is, it seems that Windows THINKING it's not connected is affecting other programs which need to connect to the internet.
View 2 Replies
View Related
Oct 1, 2012
Is there a way to generate historic reports on how many clients have been using a WLAN on Cisco 2504?
View 1 Replies
View Related
Apr 11, 2012
I could not find any report in ACS 5.3 which gives details on user creation and deletion in ACS. This feature was there in ACS 4.x but it seems not provided in 5.3 version.
View 3 Replies
View Related
May 23, 2012
dell computer claims it does not have internet availabilityWas getting internet but now Dell laptop claims it has no internet software
View 2 Replies
View Related
Apr 7, 2013
I have an issue that started showing up since I bought a new computer. The old computer ran XP, the new one runs Windows 7. Almost every time I start the computer I get an error message telling me Windows has detected an IP conflict. Sometimes when I click okay I get the message a second timeAbout half the time, I have no internet connection when I start up and have to restart my router, which fixes the problem (after restarting the modem, I do not need to do anything like renew with ipconfig; it just starts working). I do this so often I attached it to a power switch to make it easier than unplugging.My setup is this. My PC is connected to a router connected to my cable modem. The router is also connected to a wireless hub. This hub is used by only one device, my Wii U. I can get the error message even if my Wii U is turned off.
View 3 Replies
View Related
Jan 8, 2013
My customer is looking at using routers in DMVPN remote locations as DNS servers. He would like to be able to estimate how much memory the DNS cache will consume before going into production. I know you can get cache information when it's running, but he wants to plan ahead.I couldn't find any reports in Cisco or on the web of DNS caching causing memory issues, so I don't think he has much to worry about, but any rule of thumb as to how much memory each cache entry consumes would be useful. Or is there a protection mechanism to limit cache memory size in IOS ? The routers will be 877s and/or 1900-series.
View 0 Replies
View Related
Oct 5, 2012
We have a Cisco ACS 5.2 deployment (appliance). It has an existing integration with Active Directory. We utilize this with RADIUS to authenticate our wireless users and TACACS for managing our network equipment.The RADIUS reports are useful for other teams (outside my own) to be able to troubleshoot password and account lockouts (everyone forgets to change the password on their phone).I would like to allow this team and other access to view the RADIUS authentications report.
View 2 Replies
View Related
Jul 23, 2003
Running WLSE 1.3 and it shows No Data Available. Checked the task history for Inventory collection and it is not collecting. All the processes are running. Unable to gather data. SNMP community strings are configured and devices are accessible (AP350's).
View 3 Replies
View Related
May 26, 2011
I do not see any start records in Radius Accounting reports but do see only Stop records ?
btw I am running ACS 5.2
View 2 Replies
View Related
Oct 5, 2011
How to delete the accounting/authorization Reports or logs ?
View 2 Replies
View Related
Aug 30, 2011
I've just set-up one of the RV220W VPN solutions. This worked fine for a while, but now it reports the remote gateway is not responding. Other clients can connect, but not the computer I'm using at home.
Log file reports:
2011/08/31 21:10:31 [STATUS]Success to connect.
2011/08/31 21:10:31 [STATUS]Tunnel is configured. Ping test is about to start.
2011/08/31 21:10:31 [STATUS]Verifying Network...
[code]...
I've tried the most common stuff. Enabling ICMP, checked that remote administration runs on port 443, changed MTU to 1400 manually, It allows fragmented packages too. Checked that IKE and IP Sec services are running. I've also tried both with windows firewall ON and OFF. A colleague of mine had the same problem in the same time frame as me, but after a while - he suddenly was able to connect. I still can't!!
Firmware Version: 1.0.2.4
Edit: IP is not real.
View 7 Replies
View Related
May 23, 2012
How i can configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.
View 4 Replies
View Related
May 20, 2012
I have installed a WS-X4448-GB-RJ45 on a 4503 chasis. I could not get input or output rate, just shows 0 bit/seg wether or not is forwarding traffic. I would like to know if I have to make any configuration or workaround. The IOS version is 12.2(37)SG1.
View 1 Replies
View Related
Jun 27, 2012
We have been receiving these notifications on one of our core.
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host b407.f9c3.3c51 in vlan 56 is flapping between port Po5 and port Te7/2
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 145a.05c8.0ed3 in vlan 802 is flapping between port Te7/2 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 9463.d129.546a in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 3c43.8ef3.7448 in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 000e.35eb.25ae in vlan 66 is flapping between port Po5 and port Te7/2
PO5 goes to our primary wireless controller. Gi2/9 goes to a Cisco 4500 switch that also has a PO5 on it for a failover lan controller and TE7/2 is another core switch.
These mac-address all seem to point to PO 5 which is the port channel assigned to Wireless Controller interfaces.
How do I determine if this is a spanning-tree loop? No ports are err-disabled.
View 8 Replies
View Related