Running WLSE 1.3 and it shows No Data Available. Checked the task history for Inventory collection and it is not collecting. All the processes are running. Unable to gather data. SNMP community strings are configured and devices are accessible (AP350's).
View 3 RepliesI have a Cisco ACS 5.1 virtual appliance which has been working fine, I have however just discovered that it is now unable to provide me with any logs. TACACS authentication is still working without any issues, the only problem I have is viewing the logs.
View 6 Replies View Relatedwe have a 4510r-e running 12.2(50)SG1 w/ various rj45 line cards and a 24 port glc card.at any given time, i see 10's of ports in 10/full.i go to the station, and find the station in 100/full or 1000/full.
i go to the switch w/ my fluke, connect it directly to the switch w/o any intermediate infrastructure except a 50cm cat6 patch cable.the fluke reports 1000/full, but THE SWITCH PORT REPORTS STILL 10/FULL.all ports are config'd 'speed auto' and 'duplex auto'.
the switch seems to be erroneously reporting 10/full.there are no errors logged on any of the ports and there is successful communications even when the station and switch port report different speeds.even though there are no errors logged nor reported by 'show int [port]' nor 'sho int count error' certain killer applications crash on some stations. (the applications are GHOST (which dumps disk images from a server to multiple stations) and NETOP (which i sused in a classroom to transmit an instructors screen to a room full of stations) both of which broadcast and/or multicast.all nodes involved in the above 2 applics are on the same vlan and same phyiscal subnet.
the ports which report 10/full vary and occur even when the above applics are not in use.the only way i found to clear this 10/full report is by either a hardware reset of the entire module or by unplugging the cable, the execute on the port shutdown, speed auto, no shutdown, reconnect cable.then it's just a matter of time until it pops back to 10/full in a few minutes,hours or days.
how to address the killer applic problems besides restructuring the whole net by defining separate vlan for each lab of 20 or so stations?
I am monitoring my WRVS4400N with SNMP and create graphs by MRTG. Problem is that data about traffic are strange, very low. I have 50 MB line but max traffic shown on graphs is about 8000 bits per second. Also the "shape" of graph does not correspond with real traffic.
View 1 Replies View RelatedI am using 10Gig link to connect distribution and access switches. Since we are terminating the cables at multiple locations, we are also doing the link budgeting. The CISCO SFP 10G-LR module data sheet shows two values for the transmit power one of which is maximum power .5dBm and another is minimum power -8.2 dBm. Which value should I choose for the link budgeting.
View 1 Replies View RelatedI have two AIR-AP350 SERIES AP's. I am receiveing wifi from my friends house a mile away across a valley with clear line of sight. I think there is a problem with one of these units because when doing a link test one unit shows 14% signal strength on either antenna from the remote router and the second unit shows 6% on the left hand antenna and 1% on the right.
View 3 Replies View RelatedI have IOS content filtering using the Trend Micro subscription service working on a 2911 running 15.1.(3)T3 with the security license option and a 30 day demo Trend subscription. Once I figured out that the content filtering for Trend appears to be completely broken in 15.2 (even using docs for 15.2) I went back to 15.1 and it works great.
Everything seems great so far except I would like to have a more 'fancy' or custom blocked page where a user can have a couple links to either go to the trend micro reporting page [URL] or some other page, and maybe some branding so they know the page is coming from our network and is not some fake security thing or phishing attempt or whatever.
I know I can use the 'parameter-map type urlf policy trend ' section to do a tiny bit of customization of the text that appears on the default blocked page display and there is an option for it to go to a simple redirect instead ('block-page redirect -url') but how to do more with either the built in page or the redirect- url to keep the information of what page the user was trying to access and why it was blocked (category etc.) while adding more features.
Oh, one last thing, this doesn't support any kind of 'user override' or anything like that does it? So that a network can have a filter applied but an admin could override the filtering to allow temporary access to something?
I recently deployed this module on Cisco ASA 5520 (v8.2.5) at a client's place. I'm having problems. Even if there's 1 user, browsing Internet is super slow. If I were to bypass the CSC SSM (for 10 users) module by removing the "service-policy TEST interface inside" command, browsing Internet is very fast. Based on my troubleshooting, if I were to disable Web Filtering, Web Reputation and URL Blocking & Filtering, and leave all other services enabled, then the browsing is fast. how come I enable the 3 services stated above and browsing the Internet is slow, even for 1 LAN user. I don't have any thing configured under these 3 services. Just by enabling the services alone, it's already slow. It doesn't make sense for Cisco to sell such an expensive product and it can't even handle 1 user with no settings but services enabled.
View 5 Replies View Relatedwhat options are available to a customer with 800 APs that is finally migrating to a centralised model and therefore migrating from WLSE to WCS? Assuming that they move to v8 of WCS can they upgrade their WLSE licenses to WCS?
View 1 Replies View RelatedI Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies View RelatedBecause the /var is 99% full, I have problems with taking backup. I have also problems with login into the web-page. I’m authenticated, but then I get: User Role is empty.
View 5 Replies View RelatedI am having problem to configure WLSE1030 Second thing if I configured something via web browser it is not getting erased.
View 2 Replies View RelatedI cannot access WLSE, after migration from ACS 4.2 to ACS 5.2. WLSE was configured with tacacs+ management. In ACS 5.2 I've configured the optional custom attributes: groups = "System Admin"
View 2 Replies View RelatedI have a WLSE Express 1030 which is not booting. The error is "GRUB loading, please wait... Error 17". The error is a mount error for the partition. I don't have a recovery disk and I am not authorised to download the disk.
View 1 Replies View RelatedHow do I know which hardware I have? I can't find a HW version anywhere on the appliance or in WLSE itself. I am guessing 1105 beacuse I saw a 1105 as part of the path in the repository.
View 2 Replies View RelatedDoes the autonomous Cisco WAP4410N Wireless-N Access Point could be managed using Cisco Works WLSE Express.
View 1 Replies View RelatedI current have a network setup with five 1240AG access points. One is configured as a WDS. I also have a WLSE appliance. I have IAS configured on a domain controller running Cisco Secure ACS Agent. My setup works and my clients can authenticate with certificates to Active Directory. My problem is that I need to take my WLSE out of the mix - it is old and failing. I cannot afford a replacement. I know that in order to use WDS, I have to have a WLSE.
So my question is this. If I configure my APs so that do not participate in SWAN, and leave them setup to use EAP and point to my Windows IAS for RADIUS, running Cisco Secure Agent, will they be able to authenticate still.
To be honest, I set this up a long time ago and I cannot remember if the WLSE is required for domain authentication. I know if offered Domain Authentication and I have my Windows Server setup in there. So I am not sure if my APs can authenticate directly to the Windows Server without it.
We are running WCS 7.0.1 and ACS 4.2 using TACACS for our techs to login to WCS (to manage access points). However, when the tech trys to run reports, they get an error:
Permissions Denied
The user is setup in Active Directory and not in WCS. I saw something about adding the user to a group in WCS but again the user is setup in AD. Is there something we need to do in ACS? Not sure what do do.
My WLSE 1030 hard drive failed and I have replaced it with a new drive but when I boot from the 2.15 recovery CD the disc boots and runs, within the console connection I get the error "ERROR: version information not found in flash" the disc is the ejected and the system reboots.How can I reload the system software.
View 3 Replies View RelatedHave a problem with LMS 4.0.1 and DFM. In DFM no of the devices leaves the questioned state. Trying to rediscover them starts a process that ends after 20% completion every time. I've put on some debuging, but that does not enable more error messages.Only thing i find is in the log file [code] As I've encoded this to be the SNMP engine ID, which on the device is. [code]
View 4 Replies View RelatedWe have CPU reports set to run daily for some of our higher priority switches, and we've noticed that some of the data isn't meshing with what we see on the switch. We have one heavily utilized switch that reports near 100% CPU utilization sometimes. I can do a "show proc cpu history" on that switch and see that at least once an hour over 72 hours, we'll see a near 100% CPU utilization.
The problem is that these spikes never appeare on any of our reports. We'd like to see this info because even if the switch spikes for just a few seconds or a minute, it could still indicate that we may have issues. Without that in the report, we may never realize there could be a problem.
Is there a way for this info to show in the report? I'm under the impression that if LMS polls the switch and doesn't see a high utilization average, then maybe it doesnt' enter that in the report. I guess I'd just like to know how often it pulls this data, and how it decides wath the Min, Max, and Averages are.
I have modified my radius accounting reports using "interactive viewer" and saved successfully but the exported report doesn't reflect these changes. I'm just wondering what's the point of being able to modify the reports if you can't export your changes or there is something I'm missing?
View 3 Replies View RelatedWe use LMS 3.2 with the latest patches. In IPM we have a couple of collectors (availabilty latency etc) and reports for our customers.
The polling interval for all collectors are working hour 7:30 - 18:00 Mo - Fr.
Unfortunately the polling detail is not included in the PDF report. Is there a way to include this information in the report.
We're currently running on ACS 5.2.0.26.9 with 2 appliances (one primary and one secondary).Today, I wanted to get some reports from the Monitoring and Reports tool. At beginning, it seemed impossible to generate them. Later, I decided to reload first primary and then secondary. As soon as I've done it, I got an email alert telling me that it failed parsing NAD.
Cisco Secure ACS - Alarm Notification
Severity: Critical
Alarm Name
System Alarm [Collector]
Cause/Trigger
[code]....
I don't really find where I can find the Collector log...Anyway now when I generate a 30 days report, I only get data up to 23.03.2012. Nothing recent !
We had an existing installation of LMS 4.1 which seemed to have worked fine with the exception that it was giving problems with logging Syslog events. We tried everything to resolve it and then we found a link on this very site that explained that there was a bug in displaying Syslog events on LMS 4.1. It is important to state that we would get a few Syslog events but the rest were either filtered or discarded.As per the bug toolkit, we realized that we had to upgrade to LMS 4.2 to have the bug resolved. This was not a problem and we installed LMS 4.2 as a direct upgrade to LMS 4.1. We backed up our existing data and the installation process migrated everythin automatically.Now, LMS 4.2 is installed and our objective of having Syslog messages are being received regularly as we wanted.unfortunately, when we try to generate a report such as "Detailed Device" report and try to select All Devices from the Device Selector menu, we do not see any of our devices. However, we do find our devices listed under User-Defined Groups -> (Our DCR). Based on this, we can generate reports and everything is fine.Yet, we are doing this for a client of ours and they expect to see these devices listed in the "All Devices" section of the device selector. Apart from that, everything seems to be working fine.
View 2 Replies View RelatedIs there a way I can get the ACS (5.3) to email some of it's reports on a schedule?I'm hoping to send automated summaries of failed logins to the service desk each Monday morning.
View 3 Replies View Relatedi have a problem that i see the devices by ip not hostname in devices report and topology and i checked in device discovery to appear by hostname
View 2 Replies View RelatedThough other logs are being received through the email.
View 1 Replies View RelatedJust installed ACS 5.0.0.21. Monitoring and reports database was working, but now is not. When trying to open, I get "Monitoring and reports database currently unavailable. Trying reconnect in 5 minutes." From CLI "sho application status acs" gives me the following:
ACS role: PRIMARY
Process 'database' runningProcess 'management' runningProcess 'runtime' runningProcess 'adclient' runningProcess 'view-database' runningProcess 'view-collector' runningProcess 'view-jobmanager' runningProcess 'view-alertmanager' running
Also, logs show nothing unusual.
We have noticed that some devices has dissapeared from HUM pollers and some quick reports have dissapeared too. It happened again some months ago. I would like to know:
1. How I can fix it.
2. Which logs I can see to troubleshoot the problem.
3. If is possible I can restore only the hum module from LMS backup
Is there a way to configure a favorite report and share it to all all ACS administrators?
View 1 Replies View Relatedeverytime i try to sign into linksys, it reports no internet service or unidentified network
View 1 Replies View RelatedIs there a way to generate historic reports on how many clients have been using a WLAN on Cisco 2504?
View 1 Replies View Related