I have a WLSE Express 1030 which is not booting. The error is "GRUB loading, please wait... Error 17". The error is a mount error for the partition. I don't have a recovery disk and I am not authorised to download the disk.
View 1 RepliesI am having problem to configure WLSE1030 Second thing if I configured something via web browser it is not getting erased.
View 2 Replies View RelatedDoes the autonomous Cisco WAP4410N Wireless-N Access Point could be managed using Cisco Works WLSE Express.
View 1 Replies View RelatedMy WLSE 1030 hard drive failed and I have replaced it with a new drive but when I boot from the 2.15 recovery CD the disc boots and runs, within the console connection I get the error "ERROR: version information not found in flash" the disc is the ejected and the system reboots.How can I reload the system software.
View 3 Replies View RelatedI purchased several 1921 routers and the last two I setup get the following error during bootup:
%SYS-6-READ_BOOTFILE_FAIL: tftp://255.255.255.255/1:aaa1386.bin No usable interfaces.
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
%MAINBOARD_GE-3-SHUTDOWN: FPA PKT pool holding 512 particles.boot of "1:aaa1386.
bin" using boot helper "usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" failed
error returned: No usable interfaces
loadprog: error - on file open
boot: cannot load "1:aaa1386.bin"
The router moves on and eventually comes up fine and is operational. What this error is an if I can get rid of it?
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
Cisco VG224 (R527x) processor (revision 4.1) with 119808K/11264K bytes of memory. Processor board ID FGL150411MN, R527x CPU at 225MHz, Implementation 40, Rev 3.1, 1 On-Board Twenty-Four FXS Analog Voice Module V2.1, 2 FastEthernet interfaces, DRAM configuration is 64 bits wide with parity disabled. 63K bytes of non-volatile configuration memory. System fpga version is 250027, % Crashinfo may not be recovered at flash:crashinfo, % This file system device reports an error.
View 4 Replies View RelatedI recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
monitor: command "
an Aironet 1252 which is failing on boot. When power on the access-point shows the error below.
WARNING: A memory error occurred during the system start-up self-test. The device must be serviced if the error persists.
The following commands can, optionally, be used to initialize the flash file system and the TFTP file transfer system:
But when this happen, I can start the IOS manually doing flash_init and boot in ROMMON. After do this commands, the access-point starts and works normally.
How can I check and correct the memory and solve this issue?
I have a C3750E-24TD-S on which I just loaded new firmware. When I boot up I see this:Loading "c3750e-universalk9-mz.150-1.SE2.bin"...c3750e-universalk9-mz.150-1.SE2.bin: no such device
Error loading "c3750e-universalk9-mz.150-1.SE2.bin"
Interrupt within 5 seconds to abort boot process. Loading "flash:/c3750e-universalk9-mz.150-1.SE2.bin".
I am in the process of updating the software on a Catalyst 3500 series switch. I deleted the old bin file and copied over the new file via xmodem.the image I used is:
c3500xl-c3h2s-mz.120-5.WC17.bin
Once the xmodem copy is complete I performed the following sequence of steps:
File "xmodem:c3500xl-c3h2s-mz.120-5.WC17.bin" successfully copied to "flash:c350
0xl-c3h2s-mz.120-5.WC17.bin"
switch: dir flash:
Directory of flash:/
[code]....
The last output is where I am stuck. What am I missing?
Every time I delete the directory flash and reinstall it, I get an error:
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Interrupt within 5 seconds to abort boot process.
That is the message I get. It's set to NO manual boot, but it keeps making me manually boot it. I am at a loss, I've done 3 switches and they all keep doing the same thing.
I have a Cisco 2800 series and it doesn't boot, only shows this message in the CLI>
Bad RAM at location 0xA0000304: wrote 0xA0000304, read 0xA0000004
What means this? I have to change the RAM?
A new Cisco 3750V2 (WS-C3750V2-48PS-S) running IOS 'c3750-ipbasek9-mz.122-50.SE5.bin' waspurchased to add to a stack of 3 Cisco 3750 (WS- C3750- 48PS-S) switches. The IOS on the stacked switches is 'c3750-ipbase-mz.122-25.SEB4.bin'.I loaded this IOS on to the new Cisco 3750V2 and deleted its original IOS. Boot up failed with error 'hardware not supported by firmware'. I am now trying to follow the recovery procedure but the I can only initialise the flash (flash_init) and there is no 'boot_helper' command to load the boot helper files. There is no option to rum 'copy xmodem' so I cannot upload the original IOS image via xmodem on hyperterminal.
View 7 Replies View Relatedwhat options are available to a customer with 800 APs that is finally migrating to a centralised model and therefore migrating from WLSE to WCS? Assuming that they move to v8 of WCS can they upgrade their WLSE licenses to WCS?
View 1 Replies View RelatedBecause the /var is 99% full, I have problems with taking backup. I have also problems with login into the web-page. I’m authenticated, but then I get: User Role is empty.
View 5 Replies View RelatedI cannot access WLSE, after migration from ACS 4.2 to ACS 5.2. WLSE was configured with tacacs+ management. In ACS 5.2 I've configured the optional custom attributes: groups = "System Admin"
View 2 Replies View RelatedHow do I know which hardware I have? I can't find a HW version anywhere on the appliance or in WLSE itself. I am guessing 1105 beacuse I saw a 1105 as part of the path in the repository.
View 2 Replies View RelatedI current have a network setup with five 1240AG access points. One is configured as a WDS. I also have a WLSE appliance. I have IAS configured on a domain controller running Cisco Secure ACS Agent. My setup works and my clients can authenticate with certificates to Active Directory. My problem is that I need to take my WLSE out of the mix - it is old and failing. I cannot afford a replacement. I know that in order to use WDS, I have to have a WLSE.
So my question is this. If I configure my APs so that do not participate in SWAN, and leave them setup to use EAP and point to my Windows IAS for RADIUS, running Cisco Secure Agent, will they be able to authenticate still.
To be honest, I set this up a long time ago and I cannot remember if the WLSE is required for domain authentication. I know if offered Domain Authentication and I have my Windows Server setup in there. So I am not sure if my APs can authenticate directly to the Windows Server without it.
Running WLSE 1.3 and it shows No Data Available. Checked the task history for Inventory collection and it is not collecting. All the processes are running. Unable to gather data. SNMP community strings are configured and devices are accessible (AP350's).
View 3 Replies View RelatedThe Intel N-1030 just refuses to connect at N protocol. Its almost as if the N protocol has been disabled waiting for a real fix from Intel.
I have updated firmware, etc., for router. I have several N devices and ALL connect easily and quickly. I gave up for now on the Intel WLAN N-1030 and bought a Netgear N mini-usb dongle device. With coupons it was about 10 bucks at Staples. Popped it in and what do you know, connected at N in a blink of an eye.
If Netgear can get a mini-usb N device to work properly Intel and Dell? I have set everything as suggested, power to max, router channel to auto, etc. Why no selection for wireless mode b/g/n in driver but only the 802.11n mode option?
Something is not right with this driver and implementation of the N-1030. At some point Dell is going to have to step up and provide us with what THEY advertised as the hardware we purchased. Selling a device with N protocol wireless when in reality the N protocol does not work is going to be on Dell, not on Intel.
i cant activate the hard Wireless N 1030.The interface activate many seconds and desactivate im self .
View 1 Replies View RelatedI have an inspiron, with an Intel Centrioun Wireless-N 1030, that I purchased new just two months ago. I just recently starting having trouble with the wireless internet connection. I am able to connect 95% of the time, but then I cannot load one page. Occasionally, it will speed up and I have a good connection for a few minutes, but then I lose it again. It happens on battery or cord, with two different networks (one large school network and my home network). It doesn't happen if I am on a land/wired connection. The two other computers in my house, two and four years old, are having no trouble with the wireless connections. I have been using the current modem at my house since i bought the computer. Today, we reset the modem to factory settings, with no change. We also did several ping tests and had a 9% failure rate pinging th modem. I have also changed it to run at max power all the time and disabled the option to turn off when lower power, with no change. I have also attempted to update the driver through the device manager.
View 10 Replies View RelatedI have just taken delivery of a new Inspiron N5110 with an Intel Centrino N-1030 wifi card. I also have two dual band routers (LInksys WRT600N) in different locations in the house.
My problem is that the laptop is detecting my routers Wireless-G signals but NOT the Wireless-N signals. I have checked to ensure that the N-1030 card has 802.11n Mode set to Enabled and have also tried both setting under "802.11n Channel Width for band 2.4" (i.e. Auto and 20 MHz Only) with no success.
My routers are configured with the Wireless-G signal only on 2.4 GHz and Wireless-N only on 5 GHz. I found this to be the best setting to avoid interference from neighbors wifi and cordless phones and have been happily using Wireless-N with my other Dell laptop with no problems (XPS M1530 with Intel 4965agn wireless card).Does the N-1030 card not work with 5 GHz Wireless-N?
I saw some other mentions online of intermittent internet connectivity using the factory-installed Intel Centrino wireless-N 1030 card on various new Dell computers running Windows 7, but didn't see any resolution to the problem.
I can connect directly to my router via an ethernet cord, but trying to use the wireless card gives me intermittent connectivity. I will pretty quickly lose the ability to load a new page if I'm browsing with IE or Firefox, and can regain it (temporarily) by disconnecting/reconnecting or letting the wireless manager troubleshoot, during which it resets the wireless adaptor. Doing a continuous ping of my router gives me anywhere from 30-70% data loss and lengthy round trips (I am currently one foot away from the router). Other (ancient!) computers work fine on my router; I have updated the router's firmware/reset it many times, etc). I didn't specifically go download a new driver for the wireless card, but going into its properties and having it search for an updated driver results in it reporting it already has the most up-to-date driver.
I spent a lot of late nights talking to Dell support, and their eventual fix (after a complete reinstall from the factory setting partition) was to set up my home network as a WEP, which I'm not happy with due to it's poor security compared to WPA2/WPA. This appeared to resolve the connectivity issue (why??). But I feel like I should be able to use WPA2 security with a brand-new laptop. So I changed it back to WPA2/WPA and tried installing all the critical updates that Windows Update could find, including SP1, and then looked at some continuous pings of various webpages and of my router itself.
Then I noticed my ping round trip time was awesome and they were 100% successful while my computer was plugged in with the power cord, but this unfailingly changed to reporting unsuccessful pings and having 1000ms round trips as soon as I disconnect the power. Seems like the on-battery power settings are starving the wireless card?
Also, I'm sure my initial intermittent connectivity (before the complete OS reinstall) was still occurring while plugged in with the power cord, so I'm not sure if the reinstall fixed some aspect of the problem, or whether the appearance of success while plugged in now is just temporary. Perhaps my card is just bad and I need a new one? I'm using the factory default power settings and the factory-installed wireless card (and I couldn't choose a different wireless card when I built my laptop)
The wireless on my laptop keeps dropping out. When I first got it it was fine, but after a while I started experiencing problems on every wireless network I connected to. Most of the time it would connect, but after around 10 minutes or so, the connection would drop out and the wireless card has to be "reset" so I can connect again. Otherwise I have a little yellow triangle over my network signal strength bars. I've updated to the latest drivers (14.2.0.10) but it was no luck.
This happens with every wireless network and I know it's not the network because my old Vostro 1500 is running just dandy on all of them.
Well I'm typing from my tablet right now because for the 20th+ time, the Centrino 1030 card on my Vostro 3450 isn't connecting to hotel's wireless. Other places I have encountered it to have connection problems is colleges, universities, coffee shops, etc. It is also slow as molasses in my home too.
I have read other posts indicating similar problems without resolutions on the Vostro 3450. I am planning on replacing it with the BEST WLAN card there is. It seems a bit labor intensive from the service manual but doable. Has there been any "for sure" fix with the 1030 card?
The 1030 card is so incredibly bad that I am able to get 3/5 bars on my home network being outside while my Vostro can't even pick it up.
The problem is that it always stays around 121-150mbps and sometimes 270mbps(beside router). here is my wireless settings on my router
router setting 1: [URL]
router setting 2: [URL]
network card setting:
802.11n channel width:auto
802.11n mode:Enabled
Ad-hoc channel:11
Fat channel intolerant:Disabled
Roaming aggressiveness :Medium
Throughput enhancement:Disabled
Transmit power:Highest
Wireless mode:802.11a/b/g
I'm having problems connecting to the Internet using the wireless adaptor - it will connect initially but the connection is very very slow and then will eventually drop out and stop working.When I connect using an Ethernet cable, there are no problems whatsoever so I know it is not a service provider issue.I have updated the BIOS to A11 and all drivers are up to date. The wireless adaptor is Intel Centrino Wireless-N 1030. [code]
View 3 Replies View RelatedI own an Inspiron n5110 laptop(Dell) with an Intel(R) Centrino(R) Wireless-N 1030 wireless card. I use Windows 7 Ultimate 64-bit. I constantly drop internet connection, mainly when downloading and playing games. In the right bottom corner, where my wireless connection signal strenght is showed, I get an yellow triangle with '!' mark in it saying 'Limited access'. When troubleshooting, the only way to get an internet connection again, I get an message 'The default gateway is not available' and it says that it's fixed. after awhile I lose internet connection again and everything repeats. I figured out that it's not from my router or Internet Service Provider. I saw in the forums the option to exchange this card for the 6230 upgraded version but that is not a variant for me because in my country the technicians can at very damage the laptop.
View 7 Replies View RelatedMy laptop has Intel(R) Centrino(R) Wireless-N 1030 internet card but the computer can not connect to the modem properly, the speed is always not the speed that I purchased
View 1 Replies View RelatedDoes the ACS Express have the same GUI interface that the full ACS appliance? I mean if I know one I know the other?
View 4 Replies View RelatedI have acquired a Cisco 881 router and have installed CCP express onto it. The router is set to factory default and I am using IE9, Java is also installed.i try to log in using the default IP of 10.10.10.1 through the browser and the log in box pops up, I type the default "cisco - cisco" to log in, the box disappears but then nothing, just a blank browser page, CCP express refuses to boot up.PC's firewall and security programs are turned off.Pop up blockers are deactivated in browser.Flash is installed.I've tried downgrading my version of Java to various versions and doing a hard reset but still no luck.I've tried CCP Express versions 2.6 & 2.7.I have tried from 2 different PCs.I have also tried from Firefox with the same result.I am able to access the router from console and CCP full version.
View 10 Replies View Related