I have a Cisco 2800 series and it doesn't boot, only shows this message in the CLI>
Bad RAM at location 0xA0000304: wrote 0xA0000304, read 0xA0000004
What means this? I have to change the RAM?
I have Nexus 7K installations in 2 locations. Both of them have multiple VDCs. In default VDC there are continous tacacs error message though tacacs is not configured. The requests are from various public IPs where thsi VDC is not exposed to Internet at all. What would be t he cause of it?
%AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user root from 195.2.219.2
2012 Dec 11 16:25:28 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25797]
2012 Dec 11 16:25:34 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25799]
[code]....
I am having a problem with my cisco 3660 router. I have installed a wic 2T interface card and every time i set it to "no shutdown" the interface always went down and keep getting the following message " %FECPM-2-SCCFAIL: Init of SCC2 for int 0/0 failed to do fecpm_dma_init" .
View 2 Replies View RelatedI have this system: IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1
An error appear in console (many times in one minute):
Jan 3 16:25:37: %LINK-3-BADMACREG: Interface StackPort1, non-existent MACADDR registry for link 0
-Process= "<interrupt level>", ipl= 4
-Traceback= 20A364 187F04 58D6FC 58B950 2D7CE0 2E00C8 2E2BEC 2E2F24 2B0BF8
What is the problem? What is the solution?
I've taken 2 4507's fresh out of the box running CAT4500E-ENTSERVICESK9-MZ.122-53.SG2.BIN which was upgraded from CAT4500E-IPBASEK9-MZ.122-53.SG2.BIN
I'm getting constant %C4K_S2W-4-WRITECALENDARERR: Calendar write operation Failed errors on the console. I was also getting them on the original IOS version.
Anything I've seen say's to ignore them but their very frequent filling up the logs.
There's very little return on google and no bugs to report on Cisco?
I have a C3750E-24TD-S on which I just loaded new firmware. When I boot up I see this:Loading "c3750e-universalk9-mz.150-1.SE2.bin"...c3750e-universalk9-mz.150-1.SE2.bin: no such device
Error loading "c3750e-universalk9-mz.150-1.SE2.bin"
Interrupt within 5 seconds to abort boot process. Loading "flash:/c3750e-universalk9-mz.150-1.SE2.bin".
I am in the process of updating the software on a Catalyst 3500 series switch. I deleted the old bin file and copied over the new file via xmodem.the image I used is:
c3500xl-c3h2s-mz.120-5.WC17.bin
Once the xmodem copy is complete I performed the following sequence of steps:
File "xmodem:c3500xl-c3h2s-mz.120-5.WC17.bin" successfully copied to "flash:c350
0xl-c3h2s-mz.120-5.WC17.bin"
switch: dir flash:
Directory of flash:/
[code]....
The last output is where I am stuck. What am I missing?
Every time I delete the directory flash and reinstall it, I get an error:
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Interrupt within 5 seconds to abort boot process.
That is the message I get. It's set to NO manual boot, but it keeps making me manually boot it. I am at a loss, I've done 3 switches and they all keep doing the same thing.
I upgraded IOS-XE on 4500E (SUP7L-E) to cat4500e-universalk9.SPA.03.03.00.SG.151-1. I encounter the log when i try to issue write mem commad
% VRF table-id 0 not activeCompressed configuration from 8947 bytes to 2140 bytes[OK].
I have in logs following error message:
%DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module 1
Has failed test SpineControlBus 20 times on device Power Mgmt Bus on slot 10 due to error Spine control test failed error number 0x00000002.
I get a unclear log entry in a VSS system.
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
[code]....
Have a small stack of two 3750 routers. Get the following error message every few secounds:
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state UP
Now I replaced the stacking cables but no joy. It was ok for an hr or so but then the error messages popped up again. Also random links on this stack back to access layer user switches have been going up and down randomly. So I have decided to take the next step and upgrade the IOS.
Although when I try and copy a new IOS I get the following error:
%Error writing flash:/c3750-ipservicesk9-mz.122-55.SE6.bin (No space left on device)
Seems this image is 130MB while the image that is currently on it is 74MB and free space is 54MB. How do I get the image onto the router? If I delete the current image from flash will that cause the router to stop functioning?
Also I noticed there seems to be more than one flash directory. See below:
copy tftp: ?
flash1: Copy to flash1: file system
flash2: Copy to flash2: file system
flash: Copy to flash: file system
null: Copy to null: file system
nvram: Copy to nvram: file system
running-config Update (merge with) current system configuration
startup-config Copy to startup configuration
system: Copy to system: file system
vb: Copy to vb: file system
The current router image seems to be in flash1 and flash 2 also. Could I delete the image from flash1. Upload it there and then boot the router from flash1?
my MSFC2 sent this strange log message. %DATACORRUPTION-SP-1-DATAINCONSISTENCY: copy error, The error message decoder tool says: "NOT FOUND". The level is "alert".
View 8 Replies View RelatedWe are running a small network business and as funs of ciscos we own a some of the 4948s.We are facing an issue with couple of them as we get the below error message
C4K_CHASSIS-3-INSUFFICIENTPOWERSUPPLIESDETECTED:Insufficient power
supplies present for specified configuration
First thought to replace the power supply didn't actually work as we did that with no result.Power consumption is not an issue as well because all other 4948s work fine with 1 power supply (forgot to mention is 1 power supply in all of them).
I recently upgraded my network to have two 3750x core, one interface on the Cisco is connecting to a Net gear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
003396: Sep 17 01:46:16.328: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003397: Sep 17 01:46:19.843: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003400: Sep 17 01:49:58.769: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/17, changed state to down
[Code] .....
After my research i think this is a looping issue but I'm unsure how to address it.
I am receiving the following error message on a Cisco 3750 switch stack. Need troubleshooting this error message.
00:03:13: %SW_MATM-4-MACFLAP_NOTIF: Host 00d0.7400.2730 in vlan 600 is flapping between port Gi2/0/3 and port Gi2/0/2
I am receiving this error after connecting a copper adapter on a GBIC blade in a 6509. Here are the results from the show Interface. I am waiting to confirm the device on the other side settings but as far as I see I get UP and Up for protocol and line respectively.
GigabitEthernet2/11 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0009.11e4.f3ce (bia 0009.11e4.f3ce)
Description: RCPBSDEV
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]....
A new Cisco 3750V2 (WS-C3750V2-48PS-S) running IOS 'c3750-ipbasek9-mz.122-50.SE5.bin' waspurchased to add to a stack of 3 Cisco 3750 (WS- C3750- 48PS-S) switches. The IOS on the stacked switches is 'c3750-ipbase-mz.122-25.SEB4.bin'.I loaded this IOS on to the new Cisco 3750V2 and deleted its original IOS. Boot up failed with error 'hardware not supported by firmware'. I am now trying to follow the recovery procedure but the I can only initialise the flash (flash_init) and there is no 'boot_helper' command to load the boot helper files. There is no option to rum 'copy xmodem' so I cannot upload the original IOS image via xmodem on hyperterminal.
View 7 Replies View RelatedNEXUS 7000 Octopus internal error in device 78 message. I got this on NEXUS 7000 logs:
Nov 12 22:05:14 smale-outside : 2012 Nov 12 21:05:14 BRST: %MODULE-2-MOD_DIAG_FAIL: Module 2 (serial: JAF1548AMKB) reported failure on ports 2/1-2/32 (Ethernet) due to Octopus internal error in device 78 (device error 0xc4e0025b)
Nov 12 22:05:17 smale-outside : 2012 Nov 12 21:05:17 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
Nov 12 22:05:18 smale-outside : 2012 Nov 12 21:05:18 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
[code]....
I only have found:
[URL]
which does not match reality : No one was configuring Vlans.
When i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies View RelatedI need Cisco router 2800 series boot ios image from network(tftp), when flash is corrupted or router doesn't see it, so it is impossible ? Command, i used boot system tftp: ios.bin but this does not work.
View 9 Replies View Relatedmy ps3 shows a message saying 8003121 what time round about is it gunner be fixed
View 1 Replies View RelatedI have a router Cisco 2800, but always is in Rommon, the message show is:
device does not contain a valid file system
dir: cannot open device "bootflash:"
rommon 8 > dir usbflash0:
Checksum failed on c1840-usbfslib-m
Expected checksum: 91d6, calculated checksum: 4527
open: file "c1840-usbfslib-m" not found
open(): Open Error = -1
loadprog: error - on file open
cannot load the monitor library "bootflash:%c1840-usbfslib-m"
from device: usbflash0dir: cannot open device "usbflash0:"
I have faced some problem with Cisco 1520 Series APs. Since few days, We got the log in wlc 5508 like this
"AP 'MAPNSY#WMI3', MAC: ac:a0:16:5c:45:00 disassociated previously due to AP Reset. Uptime: 0 days, 00 h 22 m 52 s . Last reset reason: operator changed 11g mode."
& then AP is rebooted. Here, I attached the screenshot of WLC 5508 Log.
Laptop connects to wifi network. But it shows "No Internet Access" message.My Macbook connects to the internet just fine and the wifi on my iphone works as well.The ethernet on the laptop works and I am able to access the internet this way. The laptop does connect to some of the other access points but I've had issues with my router.I tried the usual debugging mechanisms - disable/enable adapter, reset the router, reset the tcp/ip stack. [code]
View 1 Replies View RelatedThe layer 2 switches are connected to layer 3 Switch via trunks, and routing between layer 2 switch ports with configured SVI's on 3550. All working fine. Now I'm trying to configure routing between 2800 and 3550, I tried connecting both Straight Throught and Crossover cables to the 2800 Fa0/0 and Fa0/1 ports as well as the switchports on 3550
No switchport commands are configured however, the lights do not go on for both straight through or crossover cables. I tried connecting 1750 routers but same result. My goal is to have all the VLANS routed to the internet with configuring NAT translation the router.
I've problem with IP SLA probes between two different routers.2900 (c2900-universalk9_npe-mz.SPA.151-4.M4.bin) here is set "ip sla responder" only and 2800 (c2800nm-advipservicesk9-mz.124-24.T2.bin) here is set two type of tests "udp-jitter" and "icmp-jitter" - temporary, used to check for availability of 2900 router.As a result, I've what udp-jitter doesn't work at the same time icmp-jitter test is OK.Here are the settings of IP SLA tests
ip sla 281
icmp-jitter 172.25.28.1 source-ip 192.168.28.6 num-packets 100
tos 128
frequency 120
ip sla schedule 281 life forever start-time after 00:05:45
[code]...
On cisco and am having some issues with intervlan routing. I have followed the vids and manuals but just can seem to get this working. I have the following network lab set up.
Vlan 10 = 10.70.1.9/24
Vlan 20 = 192.168.0.1/24
ME2400 firmware
ROM: Bootstrap program is ME340x boot loader
BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(35r)SE3, RELEASE SOFTWARE (fc1)
[Code]...
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
Is there any official Cisco reference to describe what is considered to be the highest acceptable production CPU load on 2800 routers? I found the document "Integrated Services Routers G2 - Performance Overview" that states at page 5,Most service providers set their CPU alarms to 60 or 65 percent. Many enterprise customers are comfortable running production networks with CPU around 70 or 75 percent.
View 3 Replies View RelatedI have a router with two interfaces what i need to filter the HTTP traffic from one interface and the rest of the traffic through the other on my cisco router 2800.
View 3 Replies View RelatedI have a problem to create a VLAN with a Cisco 2801.,I need to have base ports FastEthernet 0 / 0 and FastEthernet 0 / 1, in the same VLAN.
Basically I'm trying to switch access redundacion, now I have redundant switches in which I have the servers, but if one of these switches fails, and,coincidentally is where I have connected the router, the server runs out of internet connection.,I idea is to connect the FastEthernet 0 / 0 to a switch, and FastEthernet 0 / 1, to the other switch,but I managed to have these two ports in the same vlan, in order to have a unique IP for both FastEthernet ports,As I can do this?. do is a lot of documents using the switchport command, but this command is not available in my router, I tried different IOS, and nothing.,currently I have the following IOS: c2801-adventerprisek9-mz.124-24.T6.bin
I have a 2800 router and tried so many ways to block the unwanted sites on my office network.Like access list ip based, null0 routing and policy map. Faced issues with below config
1. Creating Access-list. very difficulty to block the sites with https those sites will be opend, and we cant block all the IPs
2. Creating null0 routing. it also a bit deficult the block maximum sites because we can't fiend all IPs for those sites
3. Policy map.. with policy map we can only 1site we can block, but not more than one..
I heard that port based routing or port based access-list are the best ways to stop the websites in my local network..for this one i need to map the site to unsued ports then i need to null rouging or need to create the access-list.