Cisco Switching/Routing :: 3750V2 Boot Up Failed With Error Hardware Not Supported By Firmware
May 10, 2012
A new Cisco 3750V2 (WS-C3750V2-48PS-S) running IOS 'c3750-ipbasek9-mz.122-50.SE5.bin' waspurchased to add to a stack of 3 Cisco 3750 (WS- C3750- 48PS-S) switches. The IOS on the stacked switches is 'c3750-ipbase-mz.122-25.SEB4.bin'.I loaded this IOS on to the new Cisco 3750V2 and deleted its original IOS. Boot up failed with error 'hardware not supported by firmware'. I am now trying to follow the recovery procedure but the I can only initialise the flash (flash_init) and there is no 'boot_helper' command to load the boot helper files. There is no option to rum 'copy xmodem' so I cannot upload the original IOS image via xmodem on hyperterminal.
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
I have a C3750E-24TD-S on which I just loaded new firmware. When I boot up I see this:Loading "c3750e-universalk9-mz.150-1.SE2.bin"...c3750e-universalk9-mz.150-1.SE2.bin: no such device
I am in the process of updating the software on a Catalyst 3500 series switch. I deleted the old bin file and copied over the new file via xmodem.the image I used is:
c3500xl-c3h2s-mz.120-5.WC17.bin
Once the xmodem copy is complete I performed the following sequence of steps:
File "xmodem:c3500xl-c3h2s-mz.120-5.WC17.bin" successfully copied to "flash:c350 0xl-c3h2s-mz.120-5.WC17.bin" switch: dir flash: Directory of flash:/
[code]....
The last output is where I am stuck. What am I missing?
Every time I delete the directory flash and reinstall it, I get an error:
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Interrupt within 5 seconds to abort boot process.
That is the message I get. It's set to NO manual boot, but it keeps making me manually boot it. I am at a loss, I've done 3 switches and they all keep doing the same thing.
We have purchased two new Nexus 3548 switches. According to documenation the Nexus 3K does support vPC. When trying to enable the feature I get this:
nexus(config)# feature vpc Error: vPC feature is not supported nexus(config)#
We are running software version version 5.0(3)A1(1) and it looks like the latest version is 5.0(3)A1(2) so that's not much of a difference.Am I missing something here?
first one had to get rid of because just wouldn't work with a 3CX server, anyway, I have a DIR-655 A4 factory shipped with 1.32NA I am trying to update the firmware to 1.34NA but it will not let me. It keeps saying Code:
We inserted GLC-T modules and on Nexus 5548 they are showing SFP validation Failed , as per Cisco doc GLC-T is support . Since we have 28 such modules and all after inserting showing same error. please see the below details. I also try configuring speed and inserting modules but no result ..let me know whether my GLC-T module is supported on Nexus 5548
INMUMFDS1SWCORE01# show module Mod Ports Module-Type Model Status --- ----- -------------------------------- ---------------------- ------------ 1 32 O2 32X10GE/Modular Supervisor N5K-C5548P-SUP active * 2 16 O2 16X10GE Ethernet Module N55-M16P ok 3 0 O2 Daughter Card with L3 ASIC N55-D160L3 ok
I have a Cisco catalyst 6513 with sup720-3bxl and WS-X6724-SFP modules , the switch was working fine until yesterday ,but after a maintenance the modue WS-X6724-SFP failed to bring online , the error code is (Module Failed SCP dnld) does it mean the module has hardware problem or i need to replace it ?
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ios version s72033-adventerprisek9_wan-vz.122-33.SXH7.bin ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- show module Mod Ports Card Type Model
In a lab environment, I have a stack of two 3750v2-48ts switches. I upgraded the stack from 15.0(1)SE2 to 15.0(1)SE3 using archive download-sw.
Switch 1 in the stack reloaded and came back with the new image.
Switch 2 appears to be dead. No console out put. When power is applied, the SYST LED blinks 22 times, then stops. I've held in the mode button for up to 60 seconds, held in mode while applying power, removed the stack cables and repeated...there's not a whole lot else I can think of to do at this point.
Yesterday I tried to install c2960-lanbasek9.mz.12.55.SE4.bin onto my router. When I changed the boot commands, I did not leave the 2nd option in there and the old firmware has an .ex3 extension. After trying to boot to this new image, we receive a looping error message that continues to reboot and go through the same process.Basically the error is "ERROR: firmware not supported by hardware"I have power cycled it a few times but durning bootup, I never see the ################## which would allow me to BREAK sequence and get into rommon. The device simply waits about 30-40 seconds after boot and goes right back to the looping reboot sequence and the error message. Is there any hyper term or putty settings to change on this?
I've been reading the documentation for the new 3750v2 switch, and I'm wondering is the IPBase license supports FULL OSPF. The product sheet notes that it supports OSPF in the IPBase license, but then further down the page it notes that for advanced routing functions (EIGRP,OSPF) you need the IPServices license. Are there any limitations to the OSPF process on a 3750v2 with the IPBase license?
According to documentation Cisco RPS 675 should have support for Cisco 3750v2 switch(WS-C3750V2-48PS).What kind of cable should be used to connect them?Cisco RPS has 16 pins and 3750v2 has 22 pins.I could not find that type of cable,
Does g0/1 port (dual purpose port but set to use sfp) support udld? If yes, what's the command to enable it? I have it connected with a 3750v2 switch. On the switch I have udld enabled.
My old switch software version is c3750-ipbase-mz.122-35.SE5 and model number is WS-C3750-48TS-S and my new switch Software version is c3750-ipservicesk9-mz.122-50.SE5.bin and model number is WS-C3750V2 . I want a compatible (prefer same) version of IOS which works on both the switches as both the switch will be in a stack..
I recently installed DHCP snooping on a 3750v2 switch (Version 12.2(55)SE4) and configured the uplink(Po2) as a trusted port. The problem is that clients cannot receive an IP address. When I disable DHCP snooping it is working properly. DHCP snooping is configured correctly but I don't have an idea how to resolve it. [code]I tested the solution on the same kind of hardware switch and firmware and it worked out fine. What is causing the clients not to receive an IP address from the DHCP server?
I have a 3560x switch with the flash formatted . I have tried to solve the problem by copying the IOS file to the flash. But the boot failed either .I have tried to copy the same IOS by the Xmodem, The boot failed again.My question is how to fixed the boot issues after the flash was formatted?
I am currently running WCS 7.0.230 I have controllers that are 2500 that are running 7.4.100.60?
My problem is that when I try to add my controller that is a Cisco 5500 running the same 7.4.100.60 I am getting the error SNMP operation to Device failed: Sparse table not supported. Verify that the WCS and WLC versions are compatible and try again.
I have double checked SNMP strings, IP Addressing and everything else I can think of. It just doesn't make sense that I can add a Controller with the same image but different hardware and no the other to the WCS server.
On cisco and am having some issues with intervlan routing. I have followed the vids and manuals but just can seem to get this working. I have the following network lab set up.
Vlan 10 = 10.70.1.9/24 Vlan 20 = 192.168.0.1/24 ME2400 firmware ROM: Bootstrap program is ME340x boot loader BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(35r)SE3, RELEASE SOFTWARE (fc1) [Code]...
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1 FastEthernet0/1 is up, line protocol is up Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
Is 'mls qos' supported on Cisco 877? I want to implement bandwidth limiting on a specific IP using access-lists on a class-map.If yes, what version and software do I need (ip base, adv security, etc)?
I purchased several 1921 routers and the last two I setup get the following error during bootup:
%SYS-6-READ_BOOTFILE_FAIL: tftp://255.255.255.255/1:aaa1386.bin No usable interfaces. %SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader. %MAINBOARD_GE-3-SHUTDOWN: FPA PKT pool holding 512 particles.boot of "1:aaa1386. bin" using boot helper "usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" failed error returned: No usable interfaces loadprog: error - on file open boot: cannot load "1:aaa1386.bin"
The router moves on and eventually comes up fine and is operational. What this error is an if I can get rid of it?
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr Missing or illegal ip address for variable IP_ADDRESS Missing or illegal ip address for variable IP_SUBNET_MASK
I unpacked a new 3560x and went to put our standard code version on it c3560e-ipbasek9-mz.122-53.SE2. Everything seemed to upgraded fine but it won't boot to a console prompt. It seems like it loads the IOS image fine but can't get passed the Front-end Microcode IMG MGR: Programming device 0. [code]
Why does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
We are trying to migrate from 1g to 10G, couldn't find any module on 6509-E which supports 10G on SFP+ ...I can see X2 and Xenpacks .. but not SFP + .what exactly this Xenpack means ?
On googling I came across documents that say OTV (Overlay Transport Virtualization) is supported on Cat 6500. Any authentic information whether OTV is supported on Cat 6500, especially with Sup-720B? FYI, Cisco Feature Navigator does not mention it.
I cannot boot IOS, when i reload this switch it go to ROMMON. I try to uploand IOS but it still has problem. i think i may wrong some point during i did uploand.
