During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
I've configured WCCP2 on my ASR1002/ESP2 and works fine. But got error log since I changed redirect ACL entries. Check on Cisco seems it a known bug?[URL] And seems any change on WCCP not take affected anymore. Even I removed all WCCP configure on my router, but my cache engine still got the redirected packet!?
Aug 8 22:41:00 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image: Batch type 6 ID 0 download to CPP failed
Aug 8 22:41:30 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image: Batch type 6 ID 0 download to CPP failed
Aug 8 22:42:00 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image: Batch type 6 ID 0 download to CPP failed
Aug 8 22:42:30 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image: Batch type 6 ID 0 download to CPP failed
[code]....
I purchased several 1921 routers and the last two I setup get the following error during bootup:
%SYS-6-READ_BOOTFILE_FAIL: tftp://255.255.255.255/1:aaa1386.bin No usable interfaces.
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
%MAINBOARD_GE-3-SHUTDOWN: FPA PKT pool holding 512 particles.boot of "1:aaa1386.
bin" using boot helper "usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" failed
error returned: No usable interfaces
loadprog: error - on file open
boot: cannot load "1:aaa1386.bin"
The router moves on and eventually comes up fine and is operational. What this error is an if I can get rid of it?
Cisco VG224 (R527x) processor (revision 4.1) with 119808K/11264K bytes of memory. Processor board ID FGL150411MN, R527x CPU at 225MHz, Implementation 40, Rev 3.1, 1 On-Board Twenty-Four FXS Analog Voice Module V2.1, 2 FastEthernet interfaces, DRAM configuration is 64 bits wide with parity disabled. 63K bytes of non-volatile configuration memory. System fpga version is 250027, % Crashinfo may not be recovered at flash:crashinfo, % This file system device reports an error.
View 4 Replies View RelatedI have a WLSE Express 1030 which is not booting. The error is "GRUB loading, please wait... Error 17". The error is a mount error for the partition. I don't have a recovery disk and I am not authorised to download the disk.
View 1 Replies View RelatedI recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
monitor: command "
an Aironet 1252 which is failing on boot. When power on the access-point shows the error below.
WARNING: A memory error occurred during the system start-up self-test. The device must be serviced if the error persists.
The following commands can, optionally, be used to initialize the flash file system and the TFTP file transfer system:
But when this happen, I can start the IOS manually doing flash_init and boot in ROMMON. After do this commands, the access-point starts and works normally.
How can I check and correct the memory and solve this issue?
I have a C3750E-24TD-S on which I just loaded new firmware. When I boot up I see this:Loading "c3750e-universalk9-mz.150-1.SE2.bin"...c3750e-universalk9-mz.150-1.SE2.bin: no such device
Error loading "c3750e-universalk9-mz.150-1.SE2.bin"
Interrupt within 5 seconds to abort boot process. Loading "flash:/c3750e-universalk9-mz.150-1.SE2.bin".
I am in the process of updating the software on a Catalyst 3500 series switch. I deleted the old bin file and copied over the new file via xmodem.the image I used is:
c3500xl-c3h2s-mz.120-5.WC17.bin
Once the xmodem copy is complete I performed the following sequence of steps:
File "xmodem:c3500xl-c3h2s-mz.120-5.WC17.bin" successfully copied to "flash:c350
0xl-c3h2s-mz.120-5.WC17.bin"
switch: dir flash:
Directory of flash:/
[code]....
The last output is where I am stuck. What am I missing?
Every time I delete the directory flash and reinstall it, I get an error:
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Interrupt within 5 seconds to abort boot process.
That is the message I get. It's set to NO manual boot, but it keeps making me manually boot it. I am at a loss, I've done 3 switches and they all keep doing the same thing.
I have a Cisco 2800 series and it doesn't boot, only shows this message in the CLI>
Bad RAM at location 0xA0000304: wrote 0xA0000304, read 0xA0000004
What means this? I have to change the RAM?
A new Cisco 3750V2 (WS-C3750V2-48PS-S) running IOS 'c3750-ipbasek9-mz.122-50.SE5.bin' waspurchased to add to a stack of 3 Cisco 3750 (WS- C3750- 48PS-S) switches. The IOS on the stacked switches is 'c3750-ipbase-mz.122-25.SEB4.bin'.I loaded this IOS on to the new Cisco 3750V2 and deleted its original IOS. Boot up failed with error 'hardware not supported by firmware'. I am now trying to follow the recovery procedure but the I can only initialise the flash (flash_init) and there is no 'boot_helper' command to load the boot helper files. There is no option to rum 'copy xmodem' so I cannot upload the original IOS image via xmodem on hyperterminal.
View 7 Replies View RelatedI am going to configure the NATing on ASR1002 and expecing to have near about 1Million nat translation. Will ASR1002 support 1million nat translations ? how many NAT translations are supportable on the ASR1002 ?I am going to configure NAT on ASR1002-5G/K9 U& have FLASR1-FWNAT-RED.
View 1 Replies View RelatedRight now I have a ASR1002 running a very old IOS version.Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1) asr1000rp1-ipbasek9.02.05.00.122-33.XNE.bin – 25-NOV-2009?
I am looking to upgrade to a newer version.I was wondering if there are any tricks when upgradeing this IOS. Is it as easy as loading the IOS onto the ASR and then changing the bootpath or is there an upgrade path I must follow? Also would there any need for a licence between 2.x and 3.x.
The loopback of the ASR1002 is 2.2.2.2. When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password.
The username/password is test okay. But somehow, the web GUI just does not use it.
Is the GLC-LH-SM SFP compatible with the ASR1002 and how does it differ from the SFP-GE-L adapter?
View 4 Replies View RelatedWe have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
View 2 Replies View RelatedI'm aware ACL's are handled in hardware on the ASR platform but wondered if there was any way to inspect how many hits we get on each line of an ACL on the ASR, I can't seem to find a command to do this.
Using LOG is not possible due to the large number of hits.
One of our customer just purchased ASR1002 router, they have three internet links from different ISPs and they dont have any remote site, they have three different public IP pool as their respective ISPs. So, is it possible to load balance the internet traffic using all three link on Cisco ASR router ( IOS - Advance Enterprise Services)
View 3 Replies View RelatedWe have a cisco7206 router which is going to be replaced with an ASR1002 router. The 7206 has some interfaces in a BVI-group - the config of which i am trying to translate over into IOS XE (which runs on the ASR1002). How to translate this config from IOS to IOS XE.
View 3 Replies View RelatedWe are having an issue with BGP flapping peer. We have a ASR1002 as Route Reflector and it work fine with all peers except with 2 peers.
View 3 Replies View Relatedim trying to create a VPN between a Cisco ASA5510 and an ASR1002 when my Loopback interface is The Source IP . [code]
View 1 Replies View Relatedwhat command is required to configure ip accounting on an interface?
I would have thought to what is required is on the interface, turn on Ip accounting i.e.
int gi0/0/0
ip accounting
However, there is no ip accounting command within the interface. We are running version Version 15.1(1)S2.
I've inherited a project building an internet connectivity solution for a large corporate. It has its own AS and its own PI space. They are putting in 100Mbit connections from 5 different Tier1's , taking full internet routing from each. Cisco ASR1002's have already been specified and purchased for the job. I'm not familiar with the ASR platform at all - is it up to the job with full routing tables? multiple instances of full tables ? (not likely to put all 5 into one box!)
View 2 Replies View Relatedwe are using an ASR 1002 for dynamic NAT (with route maps). I do have a Problem with the usage of the NAT pool it self.The total NAT Translations for the pool are:
#sh ip nat stat
[Id: 1] route-map natted-host-01 pool nat-pool-01 refcount 136
pool nat-pool-01: netmask 255.255.254.0
start XX.XX.202.0 end XX.XX.203.255
type generic, total addresses 512, allocated 88 (17%), missee 0
If i now look into the NAT translation Table i do get less entries:
#sh ip nat translations filter map-id dynamic 1 total Total number of translations: 43
Only a deeper look into the QFP gives here the right values:
# sh platform hardware qfp active feature nat data The ouput count matches the values I get if i isue a sh ip nat stat
My question is how is it handled internally.
We do have a problem too, with raising usage of the pool over the time.Once allocated Pool entries are not released after a period of time. And no NAT translation occur for that used IP NAT pool Addresses.
The timer on the device are set:
ip nat translation timeout 300
ip nat translation tcp-timeout 900
ip nat translation pptp-timeout 900
ip nat translation udp-timeout 120
ip nat translation routemap-entry-timeout 900
ip nat translation max-entries 750000
I am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
we are testing an ASR1002-X which acts as LNS for L2TP tunnels.
- All tunnels are UP (sh vpdn all return list of tunnels)
- VirtualAccess interfaces are UP
- C routes are added in routing table
but ping remote IPs don't work !!! [code]
I am trying to configure the NetFlow Top Talkers function on an ASR1002 with ADVENTERPRISEK9-M, Version 15.2(4)S. With this new Hardware and Software I am surprised to see that the command:
ip flow-top-talkers
top 50
sort-by packets
cannot be found on the CLI - it's just not there.
I have recently purchased ASR1002-RP1-ESP5 with 2 x 4K Broadband licenses to be used as LNS. Cisco have sent me PAK files for the licenses however when I try to enter the licenses into the device I get an error message saying that Licensing is not supported on this platform.
Any experience with this platform and installation of the broadband licenses?
When I spoke to Cisco TAC they told me that for this particular model the licensing is on "trust" basis where you buy license and do not install it on the actual router - similar to what 7200 used to do.
We recently purchased a Cisco ASR1002 router with four on-board Gigabit SFP-style Ethernet ports. However, when I do a "show ip interface brief", I see that there's an extra Gigabit Ethernet port. See the last interface in the following output:
ASR_1002_router#sh ip int b
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES manual down down
[Code].....
On the router itself, in addition to the four Ethernet SFP ports, there are four additional RJ-45 ports. They're labeled "BITS", "MGMT", "CON", and "AUX". I know what the Con and Aux ports are, but what are the Bits and Mgmt ports? And is one of them the Gigabit Ethernet interface that I see listed at the bottom of the output? And if it is, is there anything special about it, or is it just another routed Ethernet port? Can I do something special with it, like out-of-line managment?
We have ASR1002 routers configured to run individual SubPackages, at this point everything is operating without problems.We just received a Cisco Security Advisory informing us SSHv2 is vulnerable in our version of router code.We have to upgrade to the recommended stable release, so we downloaded, installed and expanded the IOS to expose the SubPackages on the ASR routers bootflash.
Since we are running SubPackages, do we need to upgrade all SubPackages (I.E. complete IOS upgrade) of can we just upgrade the vulnerable SubPackage? How do you determine which SubPackage contains the SSHv2 application?
We are testing an ASR1002-X which acts as LNS for L2TP tunnels.
- All tunnels are UP (sh vpdn all return list of tunnels)
- VirtualAccess interfaces are UP
- C routes are added in routing table
but ping remote IPs don't work !
LNS1# sh ver
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSAL-M), Version 15.3(2)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
We are trying to implement the ZBF on our router to assist us in limiting the intial impact of DDOS attacks.We have configured the below and it appears that it's not working, as when un der attack the statistics don't increae.
[code]...