I am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
If I implement IKE V2 on Cisco ASR 1006 Router or on firewall and sets up IPsec with IKEv1 device ( Cisco Router , Juniper etc )will it work or not ?
View 6 Replies View RelatedI was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 Replies View RelatedI want to know which of these Bluetooth module is compatible with Dell Latitude D630: 360, 365, 370, 375, 380.
View 1 Replies View RelatedIs Enhanced FlexWAN module compatible with 7603-S with RSP720-10GE?We have a PA-POS-2OC3 on a 7200 router and we want to use it on 7603-S.
View 1 Replies View RelatedWe have a core switch with the following ios and supervisor engine. Can we add a16 port LR (x2)or LRM(X2) ON the core switch?if not what modifications has to be done?if an ios upgrade is necessary is it a costly affair?At present we have two 1gb up link modules in single and multimode fiber .
#sh moduleMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL0803T308 2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAD07500600 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1439UMZK
#sh versionCisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-M), Version 12.2(33)SXI4a, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 16-Jul-10 19:51 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1) uptime is 1 year, 27 weeks, 4 days, 23 hours, 30 minutesUptime for this control processor is 1 year, 27 weeks, 4 days, 22 hours, 58 minutes(code)
The active RP of ASR 1006 router automatically switched over to standby while the standby assumed the active role.Not sure the exact reason for this behaviour. The image version is 122-33.XNB1. We noticed an outage when the switchover happened but the device did not crash.
%CMANRP-6-CMHASTATUS: RP switchover, received fastpath becoming active event%CMANRP-6-CMHASTATUS: RP switchover, received chassis event to become active%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE)%PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after chassis confirmation%NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun%CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active%PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event became active. Switch to primary (count 3)
In the output of "show redundancy switchover history" the switchover reason given is active unit failed.But currently the RPs are working as active and standby hot.
after configuring around 20 static ip routes on my ASR, and doing a 'show ip route' it doesn't really show anything.Do I need to enter another command or something, or is it because, all interfaces on the ASR are down right now, since I'm just putting the configuration on it.It currently has no reachability to the next hop for all routes, since it has no live connections on the ASR yet.
View 1 Replies View RelatedWe are trying to upgrade our ASR1006 with single RP. We got an Warning message as "superpackage install over superpackage not allowed on active RP"
how to do the upgrade properly?
I have a ASR 1006 router in my environment and I want to make it a DNS server for some reason. I tried to configure the command IP dns server on the ASR but it does not accept the command. I also have a Cisco 7206 VXR router in my environment which acepts this command.
The IOS version of my ASR is IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.1(3)S2.
New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
I have router cisco 1006 ... when I no shutdown the interface this appear to me.
Router(config)#interface gigabitEthernet 2/1/0 Router(config-if)#no Router(config-if)#no sh Router(config-if)#no shutdown Router(config-if)# *Jan 20 08:50:01.239: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/0, changed state to down *Jan 20 08:50:01.140: %LINK-3-UPDOWN: SIP2/1: Interface GigabitEthernet2/1/0, changed state to down.
I have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
We are having Cisco ASR 1006 Router with the XE Code :asr1000rp1_advance entrprisek9.03.01.00.S.150_1.S.bin The basic information we are having is
cisco ASR1006 (RP1) processor with 1717513K/6147K bytes of memory.
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
937983K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Wanted to upgrade to the latest IOS XE 3.4.x but the memory requirement for this IOS is Dram 4GB. But the DRAM actually is 2GB as per show version command.Here the Physical memory is showing 4 GB so can we upgrade this IOS XE?
I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies View RelatedI am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies View RelatedWe have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies View RelatedEarlier this AM I got an email from one of our distributors... So I began to print it. Then I realized that it was over 100 pages long. I decided to stop the printing job at that point. The printer kept printing the job still... even though I told it to cancel like 50 times.
Only thing I could thing of from there was to reboot while the printer was still going. Upon reboot I found a weird issue. Now the printer will not work with the laptop on the network.
Its prints fine on my machine... but now the laptop can only see the printer but not use it. I go to set it as the default in that machine and it says it will DL the drivers for use on printer. When I do that it just returns an error.... can not connect to printer.
I have tried to use the manual method of using a manual port setting but it just returns an access denied. How I can get this printer working on that machine. I have tried searching online for this error.
We are connected to 2 different providers (PROV01 and PROV02) with eBGP full internet tables. PROV01 routes have higher local preference over PROV02.
We are having problems with our provider and would like your expertise. PROV01, higher preference has been having trouble with their router. The BGP remains up but the router stops forwarding traffic. as a resulta we lose connection to the internet but our traffic never goes to PROV02 since PROV01 BGP remains up announcing the 400K routes to us.
Is there a way to test internet connection though PROV01 and as the "internet is DOWN" automatically change traffic to PROV02? Can BGP parameters changes be triggered by IP SLA? Our router is an ASR1006 RP2.
I've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies View RelatedI am going to configure the NATing on ASR1002 and expecing to have near about 1Million nat translation. Will ASR1002 support 1million nat translations ? how many NAT translations are supportable on the ASR1002 ?I am going to configure NAT on ASR1002-5G/K9 U& have FLASR1-FWNAT-RED.
View 1 Replies View RelatedRight now I have a ASR1002 running a very old IOS version.Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1) asr1000rp1-ipbasek9.02.05.00.122-33.XNE.bin – 25-NOV-2009?
I am looking to upgrade to a newer version.I was wondering if there are any tricks when upgradeing this IOS. Is it as easy as loading the IOS onto the ASR and then changing the bootpath or is there an upgrade path I must follow? Also would there any need for a licence between 2.x and 3.x.
The loopback of the ASR1002 is 2.2.2.2. When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password.
The username/password is test okay. But somehow, the web GUI just does not use it.
Is the GLC-LH-SM SFP compatible with the ASR1002 and how does it differ from the SFP-GE-L adapter?
View 4 Replies View RelatedWe have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
View 2 Replies View RelatedI'm aware ACL's are handled in hardware on the ASR platform but wondered if there was any way to inspect how many hits we get on each line of an ACL on the ASR, I can't seem to find a command to do this.
Using LOG is not possible due to the large number of hits.
One of our customer just purchased ASR1002 router, they have three internet links from different ISPs and they dont have any remote site, they have three different public IP pool as their respective ISPs. So, is it possible to load balance the internet traffic using all three link on Cisco ASR router ( IOS - Advance Enterprise Services)
View 3 Replies View RelatedWe have a cisco7206 router which is going to be replaced with an ASR1002 router. The 7206 has some interfaces in a BVI-group - the config of which i am trying to translate over into IOS XE (which runs on the ASR1002). How to translate this config from IOS to IOS XE.
View 3 Replies View RelatedWe are having an issue with BGP flapping peer. We have a ASR1002 as Route Reflector and it work fine with all peers except with 2 peers.
View 3 Replies View Relatedim trying to create a VPN between a Cisco ASA5510 and an ASR1002 when my Loopback interface is The Source IP . [code]
View 1 Replies View Relatedwhat command is required to configure ip accounting on an interface?
I would have thought to what is required is on the interface, turn on Ip accounting i.e.
int gi0/0/0
ip accounting
However, there is no ip accounting command within the interface. We are running version Version 15.1(1)S2.
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK