Cisco WAN :: ASR 1006 Router IOS XE Upgrade To 3.4.x?
Sep 19, 2011
We are having Cisco ASR 1006 Router with the XE Code :asr1000rp1_advance entrprisek9.03.01.00.S.150_1.S.bin The basic information we are having is
cisco ASR1006 (RP1) processor with 1717513K/6147K bytes of memory.
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
937983K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Wanted to upgrade to the latest IOS XE 3.4.x but the memory requirement for this IOS is Dram 4GB. But the DRAM actually is 2GB as per show version command.Here the Physical memory is showing 4 GB so can we upgrade this IOS XE?
View 3 Replies
ADVERTISEMENT
Aug 7, 2012
We are trying to upgrade our ASR1006 with single RP. We got an Warning message as "superpackage install over superpackage not allowed on active RP"
how to do the upgrade properly?
View 1 Replies
View Related
Apr 3, 2011
I've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies
View Related
Apr 14, 2012
The active RP of ASR 1006 router automatically switched over to standby while the standby assumed the active role.Not sure the exact reason for this behaviour. The image version is 122-33.XNB1. We noticed an outage when the switchover happened but the device did not crash.
%CMANRP-6-CMHASTATUS: RP switchover, received fastpath becoming active event%CMANRP-6-CMHASTATUS: RP switchover, received chassis event to become active%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE)%PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after chassis confirmation%NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun%CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active%PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event became active. Switch to primary (count 3)
In the output of "show redundancy switchover history" the switchover reason given is active unit failed.But currently the RPs are working as active and standby hot.
View 4 Replies
View Related
Oct 24, 2012
after configuring around 20 static ip routes on my ASR, and doing a 'show ip route' it doesn't really show anything.Do I need to enter another command or something, or is it because, all interfaces on the ASR are down right now, since I'm just putting the configuration on it.It currently has no reachability to the next hop for all routes, since it has no live connections on the ASR yet.
View 1 Replies
View Related
Apr 5, 2013
I have a ASR 1006 router in my environment and I want to make it a DNS server for some reason. I tried to configure the command IP dns server on the ASR but it does not accept the command. I also have a Cisco 7206 VXR router in my environment which acepts this command.
The IOS version of my ASR is IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.1(3)S2.
View 2 Replies
View Related
Nov 21, 2011
New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
View 7 Replies
View Related
Jan 19, 2011
I have router cisco 1006 ... when I no shutdown the interface this appear to me.
Router(config)#interface gigabitEthernet 2/1/0 Router(config-if)#no Router(config-if)#no sh Router(config-if)#no shutdown Router(config-if)# *Jan 20 08:50:01.239: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/0, changed state to down *Jan 20 08:50:01.140: %LINK-3-UPDOWN: SIP2/1: Interface GigabitEthernet2/1/0, changed state to down.
View 1 Replies
View Related
Jun 11, 2012
I have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
View 1 Replies
View Related
Sep 9, 2011
My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
View 1 Replies
View Related
Sep 13, 2012
I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies
View Related
Aug 15, 2011
I am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
View 3 Replies
View Related
Mar 18, 2013
I am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies
View Related
Jan 29, 2013
If I implement IKE V2 on Cisco ASR 1006 Router or on firewall and sets up IPsec with IKEv1 device ( Cisco Router , Juniper etc )will it work or not ?
View 6 Replies
View Related
Jan 27, 2011
We have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies
View Related
Dec 6, 2011
Earlier this AM I got an email from one of our distributors... So I began to print it. Then I realized that it was over 100 pages long. I decided to stop the printing job at that point. The printer kept printing the job still... even though I told it to cancel like 50 times.
Only thing I could thing of from there was to reboot while the printer was still going. Upon reboot I found a weird issue. Now the printer will not work with the laptop on the network.
Its prints fine on my machine... but now the laptop can only see the printer but not use it. I go to set it as the default in that machine and it says it will DL the drivers for use on printer. When I do that it just returns an error.... can not connect to printer.
I have tried to use the manual method of using a manual port setting but it just returns an access denied. How I can get this printer working on that machine. I have tried searching online for this error.
View 1 Replies
View Related
May 22, 2012
We are connected to 2 different providers (PROV01 and PROV02) with eBGP full internet tables. PROV01 routes have higher local preference over PROV02.
We are having problems with our provider and would like your expertise. PROV01, higher preference has been having trouble with their router. The BGP remains up but the router stops forwarding traffic. as a resulta we lose connection to the internet but our traffic never goes to PROV02 since PROV01 BGP remains up announcing the 400K routes to us.
Is there a way to test internet connection though PROV01 and as the "internet is DOWN" automatically change traffic to PROV02? Can BGP parameters changes be triggered by IP SLA? Our router is an ASR1006 RP2.
View 11 Replies
View Related
Mar 2, 2011
is ASR 1006 supported span port or port mirroring? Any config about that?
View 2 Replies
View Related
Oct 30, 2011
i check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies
View Related
Sep 29, 2011
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies
View Related
Jun 19, 2012
I am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
View 6 Replies
View Related
Sep 10, 2012
Is it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies
View Related
May 3, 2013
I am really stuck with router requirement for one of our client. I need 891 SEC router. I think this comes with advanced IP services. What I have is 1921, with IP Base. can I upgrade 1921, so it will become alternative to 891 SEC.
View 1 Replies
View Related
Dec 2, 2012
We have 1841 router (Cisco IOS Software, 1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(9)T1, RELEASE SOFTWARE (fc2)), currently the router up and running on "c1841-advsecurityk9-mz.124-9.T1.bin" and when we try to upgrade the IOS with "c1841-advsecurityk9-mz.124-24.T7.bin" its not taking the new IOS. [code]
View 9 Replies
View Related
Aug 16, 2011
I got a new 1811 series router. Its sh version output is " flash:c181x-advipservicesk9-mz.124-11.XW6.bin". I need to upgrade to the latest IOS. How can i find a latest one? How can i upgrade to the latest one?
View 1 Replies
View Related
Nov 6, 2012
We need to upgrade the RAM on our 3825 Cisco Router. Currently, it's 512MB and we want to upgrade it to 1GB. So do I just order another 512MB DRAM Memory? What is the part number that I need to order?
Here is the show ver:
Cisco IOS Software, 3800 Software (C3825-ADVENTERPRISEK9-M), Version 12.4(24)T2, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 19-Oct-09 21:05 by prod_rel_team(code)
View 3 Replies
View Related
May 5, 2013
My professor have asked us to do an IOS upgrade for a Cisco 827 ADSL Router. But I´am having problems to find the appropiate IOS image. The router original IOS is c827-y6-mz.121-1.XB and it supports routing protocols like rip bgp eigrp ospf is-is, etc.
Now, we have to find a newer IOS release that supports the same amount of routing protocols. This Router has only 24 MB DRAM and 8 MB Flash. We have tried with a IP PLUS/FW/IPSEC release 12.3(26) but when I write : route ? it only shows eigrp, odr and rip.
I am searching for a newer release that fits in those 24 MB and which has the other need routing protocols like ospf,bgp, etc.
an IOS image that meets what I am searching for?
View 1 Replies
View Related
Jan 9, 2012
I am looking to upgrade a 2811 router to 15.1.2T and see in the release notes that this image is only compatible with the "C Series" older ISR routers? What is a "C Series" ISR and how do I know if I have one?
View 4 Replies
View Related
Dec 1, 2011
I have router 1905 which running IOS is C1900-UNIVERSALK9-M , how can I upgrade this IOS ?
View 5 Replies
View Related
Jan 30, 2013
I wanted to know how many sodium memory slots the 1841 Routers have so i can upgrade to more then 128mb of DRAMI want ideally 256+on the Cisco website in the diagrams they dont say if it has 1 or 2 slots
View 8 Replies
View Related
Nov 10, 2011
I need to upgrade a router from a 2811 to a 3945.
2811 has the following modules:
View 1 Replies
View Related
Jul 14, 2012
I need to upgrade compact flash memory card for a 3800 router. Basically i want to upgrade code on this router and the current flash size (64Mb) cannot hold new image. I wanted to check if i swap the old flash (64 Mb) with a new one 256 mb, i will loose vlan.dat file since it's stored in flash. Is there a way i can copy vlan.dat to new flash which has new code before i change the boot statements and reload the router?
View 1 Replies
View Related
Oct 21, 2012
trying to upgrade an 1811 to the latest firmware. [code] just seems to always boot back to the original file and not the one i just tftp'd up. could it be that this router requires additional ram to support this ios?
View 5 Replies
View Related
