Cisco WAN :: ASR 1006 RP Failover?
Apr 14, 2012
The active RP of ASR 1006 router automatically switched over to standby while the standby assumed the active role.Not sure the exact reason for this behaviour. The image version is 122-33.XNB1. We noticed an outage when the switchover happened but the device did not crash.
%CMANRP-6-CMHASTATUS: RP switchover, received fastpath becoming active event%CMANRP-6-CMHASTATUS: RP switchover, received chassis event to become active%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE)%PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after chassis confirmation%NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun%CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active%PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event became active. Switch to primary (count 3)
In the output of "show redundancy switchover history" the switchover reason given is active unit failed.But currently the RPs are working as active and standby hot.
View 4 Replies
ADVERTISEMENT
Oct 24, 2012
after configuring around 20 static ip routes on my ASR, and doing a 'show ip route' it doesn't really show anything.Do I need to enter another command or something, or is it because, all interfaces on the ASR are down right now, since I'm just putting the configuration on it.It currently has no reachability to the next hop for all routes, since it has no live connections on the ASR yet.
View 1 Replies
View Related
Aug 7, 2012
We are trying to upgrade our ASR1006 with single RP. We got an Warning message as "superpackage install over superpackage not allowed on active RP"
how to do the upgrade properly?
View 1 Replies
View Related
Apr 5, 2013
I have a ASR 1006 router in my environment and I want to make it a DNS server for some reason. I tried to configure the command IP dns server on the ASR but it does not accept the command. I also have a Cisco 7206 VXR router in my environment which acepts this command.
The IOS version of my ASR is IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.1(3)S2.
View 2 Replies
View Related
Nov 21, 2011
New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
View 7 Replies
View Related
Jan 19, 2011
I have router cisco 1006 ... when I no shutdown the interface this appear to me.
Router(config)#interface gigabitEthernet 2/1/0 Router(config-if)#no Router(config-if)#no sh Router(config-if)#no shutdown Router(config-if)# *Jan 20 08:50:01.239: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/0, changed state to down *Jan 20 08:50:01.140: %LINK-3-UPDOWN: SIP2/1: Interface GigabitEthernet2/1/0, changed state to down.
View 1 Replies
View Related
Jun 11, 2012
I have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
View 1 Replies
View Related
Sep 9, 2011
My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
View 1 Replies
View Related
Sep 19, 2011
We are having Cisco ASR 1006 Router with the XE Code :asr1000rp1_advance entrprisek9.03.01.00.S.150_1.S.bin The basic information we are having is
cisco ASR1006 (RP1) processor with 1717513K/6147K bytes of memory.
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
937983K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Wanted to upgrade to the latest IOS XE 3.4.x but the memory requirement for this IOS is Dram 4GB. But the DRAM actually is 2GB as per show version command.Here the Physical memory is showing 4 GB so can we upgrade this IOS XE?
View 3 Replies
View Related
Sep 13, 2012
I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies
View Related
Aug 15, 2011
I am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
View 3 Replies
View Related
Mar 18, 2013
I am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies
View Related
Jan 29, 2013
If I implement IKE V2 on Cisco ASR 1006 Router or on firewall and sets up IPsec with IKEv1 device ( Cisco Router , Juniper etc )will it work or not ?
View 6 Replies
View Related
Jan 27, 2011
We have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies
View Related
Dec 6, 2011
Earlier this AM I got an email from one of our distributors... So I began to print it. Then I realized that it was over 100 pages long. I decided to stop the printing job at that point. The printer kept printing the job still... even though I told it to cancel like 50 times.
Only thing I could thing of from there was to reboot while the printer was still going. Upon reboot I found a weird issue. Now the printer will not work with the laptop on the network.
Its prints fine on my machine... but now the laptop can only see the printer but not use it. I go to set it as the default in that machine and it says it will DL the drivers for use on printer. When I do that it just returns an error.... can not connect to printer.
I have tried to use the manual method of using a manual port setting but it just returns an access denied. How I can get this printer working on that machine. I have tried searching online for this error.
View 1 Replies
View Related
May 22, 2012
We are connected to 2 different providers (PROV01 and PROV02) with eBGP full internet tables. PROV01 routes have higher local preference over PROV02.
We are having problems with our provider and would like your expertise. PROV01, higher preference has been having trouble with their router. The BGP remains up but the router stops forwarding traffic. as a resulta we lose connection to the internet but our traffic never goes to PROV02 since PROV01 BGP remains up announcing the 400K routes to us.
Is there a way to test internet connection though PROV01 and as the "internet is DOWN" automatically change traffic to PROV02? Can BGP parameters changes be triggered by IP SLA? Our router is an ASR1006 RP2.
View 11 Replies
View Related
Apr 3, 2011
I've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies
View Related
Mar 2, 2011
is ASR 1006 supported span port or port mirroring? Any config about that?
View 2 Replies
View Related
Oct 30, 2011
i check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies
View Related
Sep 13, 2011
Does anyone know if it's possible to use a single interface on the ASA for both the failover interface and for stateful failover? Here's my situation.I'm looking to provision a pair of ASAs and I want to do stateful failover.The problem is that I need four interfaces (inside, outside, and two physical DMZ interfaces).I'm looking at either the 5520s or 5540s and these boxes need to run the IDS SSMs, so I can't use the 4-port expansion SSM.
I want to do stateful failover so I need two failover interfaces.What I'm wondering is if I can take one physical interface,run two subinterfaces on it, and then use those two subinterfaces for my failover and stateful failover interfaces.That would leave me with the four interfaces that I need for everything else
View 3 Replies
View Related
Dec 5, 2011
We have two sites connected by a gigaman line. Routing between the two sites is done with a couple of HP routers. We also have two separate Internet connections, one at each site, through different providers. The border firewall at one site is a Cisco 5505 and at the other site it is a Cisco 5510. If the gigaman line goes down, we would like to fail over to a site-to-site VPN. Any clue how to set this up? We can set up the site-to-site VPN. how to make it serve as a failover. Another question is whether the VPN will cause confusion when the gigaman is operational.
View 11 Replies
View Related
May 7, 2013
When I try to put my ASAs in active/standby config here is the error I get.Warning: Failover message decryption failure. Pleas make sure both units have the same failover shared key and crypto license or the system is out of memory.
View 1 Replies
View Related
Nov 10, 2011
I got PIX 525 with failover. Due to power issue one Unit was offline for a while. During this time couple of changes was done on the Firewall.
Which Unit becomes active when I plug the Firewall unit which was offline for a while now. Each Unit has 4 Ethernet Connection
E 0/0 - connects ISP Router
E 0/1 - connects to Lan switch
E 1/0 - connects to DMZ port
E 2/0 - connects to failover unit PIX
View 4 Replies
View Related
Mar 17, 2013
Ongoing problem I have been having regarding a l2l VPN connection between our ASA 5510 and a client's ASA 5505. The client's main ISP is Comcast and he uses a secondary AT&T internet connection as a failover. When Comcast goes down, AT&T comes up and everything works great...except for the VPN to our ASA5510. I have not been able to get the VPN connection to work on the failover network. I have set up a separate, "Backup_WAN", interface in the firewall for AT&T. All of the same rules are in place for AT&T as there are for the primary Comcast connection (the VPN for Comcast works just fine) but I still cannot get the VPN to work with the failover.
Why the VPN would not be working?
View 11 Replies
View Related
May 3, 2011
We have a customer requirement of providing secure connectivity from Remote Office to HQSame time to provide certain level of layer 3 redundancy via secondary link should the primary link fail We are looking at ASA5500 series firewall for both Remote office and HQ.Can this be done?
View 3 Replies
View Related
Aug 24, 2011
We are trying to make a VPN failover over two ASA's. However the 2 ASA's have different version and our smartnet have already expired. I was wondering if this VPN failover would work even if they are different? Or should I get a smartnet first to be able to download an updated ios?
ASA Version 8.0(3)6
ASA Version 7.0(6)
View 8 Replies
View Related
Apr 28, 2011
My Location CanadaI would like to connect to separate VPN’s located in England which connect to servers located outside of the UK.I would like to set the 2nd VPN as a failover.If 2nd VPN fails I would like the connection to break and not failover to my Canada connection.
View 4 Replies
View Related
May 16, 2011
I need to configure one interface in failover because the client has 2 ISP.[CODE]
View 2 Replies
View Related
Jun 20, 2011
Currently we have one ISP1 and all traffic goes to this way. Suppose our isp1 goes down, our outside user cant get the server. All servers are nated to this ISP1.We planned to purchase a another ISP2. Shall we Configure same inside server to map this ISP2? so that one primary ISP1 goes down it will take place the outside trafficISP2.
View 1 Replies
View Related
May 18, 2011
I thing that i find some bug in the newest IOS 15.1.4M.
The case is falow:
I start to configure failover for the costomer - make default route, make the default path but i cant find the comand IP SLA monitor. Is some meet this problem with this IOS or just Cisco make some chenge in the CLI commands?
Tomorrow i will try with IOS version 15.1.1T.
View 2 Replies
View Related
Sep 10, 2012
I have an ASA5515 and our remote sites which have a mesh topology of VPN. At some times of the day router to particular links are down do to the ISP core, but the tunnels from the same firewall can communicate to other sites. Is it possible to have a way where you could route traffic to another ASA which has a connection to both the ASA which want to communicate and have the traffic hairpinned, I know this is possible but is it possible to make this automated.
View 5 Replies
View Related
Nov 23, 2011
How to configure ASA failover for 8.4.
View 1 Replies
View Related
Aug 2, 2011
We have two offices in the US and one in Mexico. Our site in Mexico connects to our headquarters in the US over an AVPN/ MPLS circuit .Mexico has a separate Internet connection through TelMex. There is an ASA 5510 at headquarters and an ASA 5505 in Mexico. We have a fail over VPN set up in the ASAs for times when the MPLS circuit goes down. All Internet traffic in Mexico is supposed to be routed to the TelMex connection. All company traffic is supposed to be routed to the Cisco router. ASA is supposed to be last resort route. We have a fail over VPN set up in the ASAs for times when the MPLS circuit goes down. (Or at least we did until I had someone work on the configuration) Everything had been working fine for the last 4 years.
Yesterday when the MPLS went down, so did their Internet connection. I realized the Internet traffic is now coming through the MPLs circuit to head quarters and out our ASA. Obviously there is a problem with the configuration. I do not have enough experience to figure this out. I have attached the configs and the routes for both the ASA and the router.
View 11 Replies
View Related
