Cisco WAN :: How To Upgrade Single RP ASR 1006
Aug 7, 2012We are trying to upgrade our ASR1006 with single RP. We got an Warning message as "superpackage install over superpackage not allowed on active RP"
how to do the upgrade properly?
ADVERTISEMENT
Cisco WAN :: ASR 1006 Router IOS XE Upgrade To 3.4.x?
Sep 19, 2011We are having Cisco ASR 1006 Router with the XE Code :asr1000rp1_advance entrprisek9.03.01.00.S.150_1.S.bin The basic information we are having is
cisco ASR1006 (RP1) processor with 1717513K/6147K bytes of memory.
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
937983K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Wanted to upgrade to the latest IOS XE 3.4.x but the memory requirement for this IOS is Dram 4GB. But the DRAM actually is 2GB as per show version command.Here the Physical memory is showing 4 GB so can we upgrade this IOS XE?
Cisco Switching/Routing :: Upgrade On 4507R+E Single SUP?
Mar 3, 2013how to upgrade firmware on 4507 6L-E Sup. There is only 1 Sup on the switch. is there any special requirement to update the firmware when switch not running on redundancy mode?
-core-1#show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit = Primary Unit ID = 3
Redundancy Mode (Operational) = Stateful Switchover Redundancy Mode (Configured) = Stateful SwitchoverRedundancy State = Non Redundant
[Code] ......
Cisco WAN :: ASR 1006 RP Failover?
Apr 14, 2012The active RP of ASR 1006 router automatically switched over to standby while the standby assumed the active role.Not sure the exact reason for this behaviour. The image version is 122-33.XNB1. We noticed an outage when the switchover happened but the device did not crash.
%CMANRP-6-CMHASTATUS: RP switchover, received fastpath becoming active event%CMANRP-6-CMHASTATUS: RP switchover, received chassis event to become active%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE)%PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after chassis confirmation%NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun%CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active%PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event became active. Switch to primary (count 3)
In the output of "show redundancy switchover history" the switchover reason given is active unit failed.But currently the RPs are working as active and standby hot.
Cisco WAN :: ASR 1006 IP Routing?
Oct 24, 2012after configuring around 20 static ip routes on my ASR, and doing a 'show ip route' it doesn't really show anything.Do I need to enter another command or something, or is it because, all interfaces on the ASR are down right now, since I'm just putting the configuration on it.It currently has no reachability to the next hop for all routes, since it has no live connections on the ASR yet.
View 1 Replies View RelatedCisco WAN :: IP DNS Server Configuration In ASR 1006
Apr 5, 2013I have a ASR 1006 router in my environment and I want to make it a DNS server for some reason. I tried to configure the command IP dns server on the ASR but it does not accept the command. I also have a Cisco 7206 VXR router in my environment which acepts this command.
The IOS version of my ASR is IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.1(3)S2.
Cisco WAN :: Creating Vlan On ASR 1006?
Nov 21, 2011New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
Cisco WAN :: 1006 Showing Interface Down
Jan 19, 2011I have router cisco 1006 ... when I no shutdown the interface this appear to me.
Router(config)#interface gigabitEthernet 2/1/0 Router(config-if)#no Router(config-if)#no sh Router(config-if)#no shutdown Router(config-if)# *Jan 20 08:50:01.239: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/0, changed state to down *Jan 20 08:50:01.140: %LINK-3-UPDOWN: SIP2/1: Interface GigabitEthernet2/1/0, changed state to down.
Cisco WAN :: ASR 1006 Not Being Able To Bring Interface Up
Jun 11, 2012I have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
Cisco WAN :: ASR 1006 - IRB Feature Is Not Supported
Sep 9, 2011My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
Cisco WAN :: ASR 1006 Management Port
Sep 13, 2012I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies View RelatedCisco WAN :: ASR1002 / 1006 SFP Compatibility With SPA Module?
Aug 15, 2011I am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
Cisco WAN :: To Enable 5X1GE V2 Modules On ASR 1006
Mar 18, 2013I am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies View RelatedCisco VPN :: IKEV2 IKEV1 Compatibility With ASR 1006
Jan 29, 2013If I implement IKE V2 on Cisco ASR 1006 Router or on firewall and sets up IPsec with IKEv1 device ( Cisco Router , Juniper etc )will it work or not ?
View 6 Replies View RelatedCisco WAN :: How To Available License On ASR 1006 / 9000 Series
Jan 27, 2011We have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies View RelatedNetworking :: HP 1006 Could Not Stop Printing When Cancelled
Dec 6, 2011Earlier this AM I got an email from one of our distributors... So I began to print it. Then I realized that it was over 100 pages long. I decided to stop the printing job at that point. The printer kept printing the job still... even though I told it to cancel like 50 times.
Only thing I could thing of from there was to reboot while the printer was still going. Upon reboot I found a weird issue. Now the printer will not work with the laptop on the network.
Its prints fine on my machine... but now the laptop can only see the printer but not use it. I go to set it as the default in that machine and it says it will DL the drivers for use on printer. When I do that it just returns an error.... can not connect to printer.
I have tried to use the manual method of using a manual port setting but it just returns an access denied. How I can get this printer working on that machine. I have tried searching online for this error.
Cisco WAN :: ASR 1006 RP2 - Change Upstream Provider Without Losing BGP Connection
May 22, 2012We are connected to 2 different providers (PROV01 and PROV02) with eBGP full internet tables. PROV01 routes have higher local preference over PROV02.
We are having problems with our provider and would like your expertise. PROV01, higher preference has been having trouble with their router. The BGP remains up but the router stops forwarding traffic. as a resulta we lose connection to the internet but our traffic never goes to PROV02 since PROV01 BGP remains up announcing the 400K routes to us.
Is there a way to test internet connection though PROV01 and as the "internet is DOWN" automatically change traffic to PROV02? Can BGP parameters changes be triggered by IP SLA? Our router is an ASR1006 RP2.
Port Forwarding - Router Belkin F5D7234-4 V5 And Modem Motorola 2210-02-1006
Apr 3, 2011I've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies View RelatedCisco WAN :: ASR 1006 Supported Span Port Or Port Mirroring?
Mar 2, 2011is ASR 1006 supported span port or port mirroring? Any config about that?
View 2 Replies View RelatedCisco Firewall :: Firewall / Can ASR 1006 Replace ASA 5580
Oct 30, 2011i check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies View RelatedCisco Wireless :: 1242 - Cannot Upgrade AP To LWAP Using Upgrade Tool On Windows 7
Sep 29, 2011I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies View RelatedCisco Wireless :: 5500 AP Upgrade Lic Upgrade On Controller
Jun 19, 2012I am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
AAA/Identity/Nac :: CSACS-1121-UP-K9 - Possible To Upgrade It Being Non Upgrade Part
Sep 10, 2012Is it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies View RelatedCisco :: STP With Switches Linked By Single Hub?
Sep 28, 2012Question: how would STP or RSTP behave in a star topology with a hub in the middle?i.e. you have four switches all linked to the same central hub. Single links, no loops.Each switch would then get BPDUs from everybody.Going by theory, it should be OK since it still sees the root's BPDU and will see the link to the hub as the root port, despite presence of other BPDUs from other switches? No different from receiving an inferior BPDU from an upstream switch and a superior BPDU from a further upstream root switch.I guess I could lab it by turning off spanning tree on a switch to simulate a hub? I've never previously had to deal with STP issues where there are hubs that aren't strictly point to point bridging so to speak (ok they're not bridging but you get the drift).I've got a scenario I'm examining at the moment where this is the topology, except all switches have bpdufilter running hence effectively no spanning tree. I'm curious to know what would happen should I remove the bpdufilter.I realise there is zero benefit in spanning tree in this instance as I don't have any redundant loops to fall back on, but I'm reluctant to turn off STP on those vlans (since obviously theres stuff behind those switches). The BPDUfilter method seems like an elegant solution but I wonder if its actually necessary.(the hub is actually a VPLS mesh, most sites terminate PE to CE router but I'm playing around with switches as the termination points – run our own Q in Q, split vlans off before it gets to layer 3 as separation, etc.)
View 1 Replies View RelatedCisco Wireless :: RV110W - What Single POE Is Available
May 7, 2012I have a client that requires a single router with POE for placement at an economical price. I was considering the Linksys WAPPOE12, but that is discontinued. What would work with that router?
View 2 Replies View RelatedCisco WAN :: 1841 - Many NAT In A Single Router
Nov 11, 2012I have got a cisco 1841 router. I need to do many nat. I have got a lots of virtual interface on this router. How many nat inside and outside does it supports ? Can I do more than one nat insdie and outside in different virual interfaces on the same single router.
View 2 Replies View RelatedCisco WAN :: 7609 - Redundancy To Single ISP
Dec 12, 2011First and foremost, what I have are 2 x 7204VXR (Gateways), 1 x 4507R-E (Coreswitch), and our ISP have 7609.Got some issues with redundancy with our ISP.
7609
I I
I I
7204-A 7204-B
| |
| vrrp |
| |
-4507R-E-
|
|
internal network
Both outside interfaces of 7204 gateways are connecting to 7609 with different public ip block. I used VRRP for my internal nework and failover have been tested working.
Even tried to remove link of 7204-A and 7609, the failover works perfect. If I shutdown/ remove the link between my 4507R-E and 7204-A (primary gw_higher vrrp priority), vrrp redundancy/failover still works, but pings from internal network to internet is only 50% success....alternate 4 ping reply and 4 time out.
Cisco VPN :: 881 W Limit VPN Traffic From Single IP
Jul 27, 2011I have just set up a 881W appliance for a satellite office. At this time, we don't need a site to site vpn. However, I have EZVpn configured on it and working great so that I can connect from our main office for admin purposes. How can I setup up a firewall rule/policy in order for only our main office IP to connect to Ezvpn? I don't want to allow access to the VPN from any other IP other than our IP at our main office.
View 2 Replies View RelatedCisco VPN :: Single ASA5510 - Two Public IPs For Web VPN
May 5, 2013We have an asa5510 running as an SSL VPN gateway using one public IP address (e.g. 1.1.1.1) as the target IP address for the users.
Now we need to run a 2nd public IP address on the same asa5510 as target IP address for a different set of users, e.g. 2.2.2.2.
NAT is not working, secondary IP address is not possible, sub-interface is not the right way. Is this really not possible?
Cisco WAN :: Can Use 1 Single IOS In All 3845 Router
Aug 16, 2011Can i Use 1 single IOS in all 3845 Router?
I have S384AESK9-124xx (T) version IOS in one of my 3845 router, can i copy the IOS and install it in my 4 x 3845 Router as i require (T) Version IOS to support HWIC-2FE module.
Like wise, i have Cisco 1800 IOS- S184AESK9-124xx (T) and Cisco 2800 IOS- S28NAESK9-124xx (T) installed in my routers, will there be any issues if i copy and use the same IOS in all my respective devices?
Cisco LAN :: SA 500 - DMZ Over Single Uplink And Switches
Feb 7, 2013I have an SA 500 with the optional port configured as the DMZ. The LAN ports are running the 192 range and the DMZ is the 172 range.
I have seperate offices (A few hundred feet apart) that have been connected with 2 un managed switches up linked with a single wire. The 192 range stuff runs over this. I need to get the DMZ out to the second room and was asking about how to do this over the single up link and switches. (Trying not to run a second wire)
My lack of understanding had me draw up this diagram attached as a picture, to ask about. What it shows is me trying to get the DMZ through the up linked switches to the other room. I thought of using 2 routers, one on each end. I've been told this is incorrect and wont work.
Maybe a purchase of a second hardware and eliminate the switches? (up link the SA 500 to another device?) What should that device be?
What All Can Cause A Single IP To Be Blocked
Aug 10, 2011I can get to anywhere I want on the web except one IP, and I can't ping it either. What can cause this? (Security off)...
View 6 Replies View RelatedMultiple IPs On A Single NIC?
Nov 9, 2011Am trying to understand how we can have multiple IP addresses on a single NIC and what are the restrictions on the same. If i can have two IPs from two different networks present on a single NIC, then why would i ever get a new NIC?
Also, i want to understand the concept of virtual IP and how it fits into this picture.