New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
we have two Catalyst Express 500 switches and a ESW 520 just purchased. the VLAN on the other two is 2. how do I change the Default to be 2 instead of 100 in the ESW Switch.
View 3 Replies View RelatedI'm creating 3 vlans, one private ip addresses and the two for two blocks of public ips. After creating them devices on the same network are able to talk to each other on the private IP but not on the public ips.
View 1 Replies View RelatedI just procured Cisco 3560V2- 48PS-S i would like to know how to set it up from scratch:
1. configuring passwords: enable and privilege
2. Creat Vlan , such that systems connected to the Vlan can connect to internet.
3. enable routing protocols
4. How do i use the switch as a default gateway for the systems on the vlan
5. how do i make sure the desktops connected to the switch are browsing the internet.
I have a problem to create a VLAN with a Cisco 2801.,I need to have base ports FastEthernet 0 / 0 and FastEthernet 0 / 1, in the same VLAN.
Basically I'm trying to switch access redundacion, now I have redundant switches in which I have the servers, but if one of these switches fails, and,coincidentally is where I have connected the router, the server runs out of internet connection.,I idea is to connect the FastEthernet 0 / 0 to a switch, and FastEthernet 0 / 1, to the other switch,but I managed to have these two ports in the same vlan, in order to have a unique IP for both FastEthernet ports,As I can do this?. do is a lot of documents using the switchport command, but this command is not available in my router, I tried different IOS, and nothing.,currently I have the following IOS: c2801-adventerprisek9-mz.124-24.T6.bin
We have observed WS-C4507R-E got rebooted while creating the L3 VLAN ( while No shut).Is there any known bug for below IOS ?cat4500-entservicesk9-mz.122-40.SG.bin,
View 4 Replies View RelatedI have Linksys SPS224Trying to create VLAN through SNMP. Issueing the string to create VLAN ID=100 with name "VLAN100"
snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.100 s VLAN100 .1.3.6.1.2.1.17.7.1.4.3.1.5.100 i 4
It reports
Error in packet.
Reason: (genError) A general failure occured
Failed object: iso.3.6.1.2.1.17.7.1.4.3.1.1.100
In same time changing the name of existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.23 s VLAN23 and even deleting the existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.510 i 6 are successful.
How can I create new vlan through SNMP?
My core switch is a 6509-e and my IDF closets have 3750's.I have a couple of vlans currently setup, that can communicate with each other.VTP is setup Client/Server where as my core is Server, all IDF's are Client.
What i'm trying to do is create an isolated VLAN. I want to setup a DHCP scope and use helper address. When i plug in a client to that VLAN, i want it to get an IP, but not have any other network access.
Is this possible to do without switching to Transparent mode? If not - what reprocussions will i see by switching to transparent mode?
I was given a task of creating a vlan and isolating one pc to access an internal website (192.168.90.15) on a specific port (port 8080)The pc is connected in the following manner:
PC--> HP Switch --> Cisco Small Business SG200 switch --> 3550 Catalyst 1, 3550 Catalyst 2 and 3550 Catalyst 3.
I have created a vlan 110 on the Main 3550 Catalyst switch and successfully added the pc to that vlan.However, that PC must be able to access the internet and an internal website on port 8080.I have placed an access-list on the main 3550 catalyst switch which is connected to our router as below:
Client ip address: 192.168.100.2
VLAN 110: 192.168.100.3
access-list 110 permit tcp host 192.168.100.2 host 192.168.90.15 eq 8080access-list 110 permit icmp host 192.168.100.2 anyaccess-list 110 deny ip 192.168.100.0 0.0.0.255 ? I was unable to access the webserver even after many attempts.
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies View RelatedThe active RP of ASR 1006 router automatically switched over to standby while the standby assumed the active role.Not sure the exact reason for this behaviour. The image version is 122-33.XNB1. We noticed an outage when the switchover happened but the device did not crash.
%CMANRP-6-CMHASTATUS: RP switchover, received fastpath becoming active event%CMANRP-6-CMHASTATUS: RP switchover, received chassis event to become active%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE)%PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after chassis confirmation%NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun%CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active%PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event became active. Switch to primary (count 3)
In the output of "show redundancy switchover history" the switchover reason given is active unit failed.But currently the RPs are working as active and standby hot.
after configuring around 20 static ip routes on my ASR, and doing a 'show ip route' it doesn't really show anything.Do I need to enter another command or something, or is it because, all interfaces on the ASR are down right now, since I'm just putting the configuration on it.It currently has no reachability to the next hop for all routes, since it has no live connections on the ASR yet.
View 1 Replies View RelatedWe are trying to upgrade our ASR1006 with single RP. We got an Warning message as "superpackage install over superpackage not allowed on active RP"
how to do the upgrade properly?
I have a ASR 1006 router in my environment and I want to make it a DNS server for some reason. I tried to configure the command IP dns server on the ASR but it does not accept the command. I also have a Cisco 7206 VXR router in my environment which acepts this command.
The IOS version of my ASR is IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.1(3)S2.
I have router cisco 1006 ... when I no shutdown the interface this appear to me.
Router(config)#interface gigabitEthernet 2/1/0 Router(config-if)#no Router(config-if)#no sh Router(config-if)#no shutdown Router(config-if)# *Jan 20 08:50:01.239: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/0, changed state to down *Jan 20 08:50:01.140: %LINK-3-UPDOWN: SIP2/1: Interface GigabitEthernet2/1/0, changed state to down.
I have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
We are having Cisco ASR 1006 Router with the XE Code :asr1000rp1_advance entrprisek9.03.01.00.S.150_1.S.bin The basic information we are having is
cisco ASR1006 (RP1) processor with 1717513K/6147K bytes of memory.
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
937983K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Wanted to upgrade to the latest IOS XE 3.4.x but the memory requirement for this IOS is Dram 4GB. But the DRAM actually is 2GB as per show version command.Here the Physical memory is showing 4 GB so can we upgrade this IOS XE?
I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies View RelatedI am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
I am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies View RelatedIf I implement IKE V2 on Cisco ASR 1006 Router or on firewall and sets up IPsec with IKEv1 device ( Cisco Router , Juniper etc )will it work or not ?
View 6 Replies View RelatedWe have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies View RelatedEarlier this AM I got an email from one of our distributors... So I began to print it. Then I realized that it was over 100 pages long. I decided to stop the printing job at that point. The printer kept printing the job still... even though I told it to cancel like 50 times.
Only thing I could thing of from there was to reboot while the printer was still going. Upon reboot I found a weird issue. Now the printer will not work with the laptop on the network.
Its prints fine on my machine... but now the laptop can only see the printer but not use it. I go to set it as the default in that machine and it says it will DL the drivers for use on printer. When I do that it just returns an error.... can not connect to printer.
I have tried to use the manual method of using a manual port setting but it just returns an access denied. How I can get this printer working on that machine. I have tried searching online for this error.
We are connected to 2 different providers (PROV01 and PROV02) with eBGP full internet tables. PROV01 routes have higher local preference over PROV02.
We are having problems with our provider and would like your expertise. PROV01, higher preference has been having trouble with their router. The BGP remains up but the router stops forwarding traffic. as a resulta we lose connection to the internet but our traffic never goes to PROV02 since PROV01 BGP remains up announcing the 400K routes to us.
Is there a way to test internet connection though PROV01 and as the "internet is DOWN" automatically change traffic to PROV02? Can BGP parameters changes be triggered by IP SLA? Our router is an ASR1006 RP2.
I've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies View Relatedis ASR 1006 supported span port or port mirroring? Any config about that?
View 2 Replies View Relatedi check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies View RelatedI has got a 8 system(Say Node1, Node2,.....,Node7,Node8) in my LAN Network.i Want a Group a 8 System's in Such a way that Node 2 Should Ping with Node1,Node3 Node4, But not with Node 5,Node 6,Node 7,Node 8.
View 2 Replies View Relatedi am trying to make site to site VPN on cisco 1841 router using SDM , but I faced a strange problem . I successfully install sdm , internet browser , disabled block pop up , and java . i successfully can run SDM and configure the router using it .
BUT\ when I select VPN>>Site to site VPN >>Create Site to Site VPN tap >> and Press on Lanuch the selected task to start the creation process using the wizard Unfortunately it is not working ,, I don't know why ?
I tried with another PC , another SDM version , another browser .
I'm trying to create a VPN at our office. However I cant seem to ping our servers public IP. I have tried configuring our router to do this. However, it times out when you are outside of our network.
View 4 Replies View RelatedI have a VM (Alice).I want to route ALL its traffic through a server of my own in the UK.It needs to be 'fail-safe' in the sense that the traffic must either be routed through the server, or not at all (EG with windows VPN dialer, if the VPN connection is dropped it will immediately begin routing traffic normally again - that's not acceptable*). I need to run windows on the VM, the server can be anything.The VM is connected to the internet via a linux firewall/router box in my house (set as default gateway for the VM).How can I set this up?
View 5 Replies View RelatedI am a bit confused on how to create a Hot Spot & connect a Dell Desktop(no built in WIFI) a Dell Laptop(with built in WIFI) & a HP Printer with WIFI. From reading info on your Web Site, it appears that I need a Wireless Router, an adapter(not sure what this is) for my Desktop. I have AT&T Air Card internet access. Do I need anything else?
View 1 Replies View Related