Cisco Switches :: Linksys SPS224 / Creating VLAN Through SNMP
May 30, 2011
I have Linksys SPS224Trying to create VLAN through SNMP. Issueing the string to create VLAN ID=100 with name "VLAN100"
snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.100 s VLAN100 .1.3.6.1.2.1.17.7.1.4.3.1.5.100 i 4
It reports
Error in packet.
Reason: (genError) A general failure occured
Failed object: iso.3.6.1.2.1.17.7.1.4.3.1.1.100
In same time changing the name of existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.23 s VLAN23 and even deleting the existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.510 i 6 are successful.
I have Linksys SPS224. I've learnt how to change some parameters through SNMP. But this changes are applying to running-config, and, when switch reboots, all loose.
How can I save this changed running-config to startup-config through SNMP?
we have two Catalyst Express 500 switches and a ESW 520 just purchased. the VLAN on the other two is 2. how do I change the Default to be 2 instead of 100 in the ESW Switch.
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
Any snmpset commands to modify port vlan membership on SG300-28 switches? I checked [URL] however this information is apparently only valid for catalysts.
The latest firmware is installed and the provided MIB files are used.
I am trying to track down the SNMP MIBs for the Linksys by Cisco SRW2048. Please note that this is the model before the complete CISCO rebrand of the product. I have SNMP walked, browsed etc etc and I just can't pull CPU and RAM usage. Any working view of those two stats? I'm using OpManager by ManageEngine as my NPM platform.
New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
I'm creating 3 vlans, one private ip addresses and the two for two blocks of public ips. After creating them devices on the same network are able to talk to each other on the private IP but not on the public ips.
I just procured Cisco 3560V2- 48PS-S i would like to know how to set it up from scratch:
1. configuring passwords: enable and privilege 2. Creat Vlan , such that systems connected to the Vlan can connect to internet. 3. enable routing protocols 4. How do i use the switch as a default gateway for the systems on the vlan 5. how do i make sure the desktops connected to the switch are browsing the internet.
I have a problem to create a VLAN with a Cisco 2801.,I need to have base ports FastEthernet 0 / 0 and FastEthernet 0 / 1, in the same VLAN. Basically I'm trying to switch access redundacion, now I have redundant switches in which I have the servers, but if one of these switches fails, and,coincidentally is where I have connected the router, the server runs out of internet connection.,I idea is to connect the FastEthernet 0 / 0 to a switch, and FastEthernet 0 / 1, to the other switch,but I managed to have these two ports in the same vlan, in order to have a unique IP for both FastEthernet ports,As I can do this?. do is a lot of documents using the switchport command, but this command is not available in my router, I tried different IOS, and nothing.,currently I have the following IOS: c2801-adventerprisek9-mz.124-24.T6.bin
We have observed WS-C4507R-E got rebooted while creating the L3 VLAN ( while No shut).Is there any known bug for below IOS ?cat4500-entservicesk9-mz.122-40.SG.bin,
My core switch is a 6509-e and my IDF closets have 3750's.I have a couple of vlans currently setup, that can communicate with each other.VTP is setup Client/Server where as my core is Server, all IDF's are Client.
What i'm trying to do is create an isolated VLAN. I want to setup a DHCP scope and use helper address. When i plug in a client to that VLAN, i want it to get an IP, but not have any other network access.
Is this possible to do without switching to Transparent mode? If not - what reprocussions will i see by switching to transparent mode?
I'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
I was given a task of creating a vlan and isolating one pc to access an internal website (192.168.90.15) on a specific port (port 8080)The pc is connected in the following manner:
PC--> HP Switch --> Cisco Small Business SG200 switch --> 3550 Catalyst 1, 3550 Catalyst 2 and 3550 Catalyst 3.
I have created a vlan 110 on the Main 3550 Catalyst switch and successfully added the pc to that vlan.However, that PC must be able to access the internet and an internal website on port 8080.I have placed an access-list on the main 3550 catalyst switch which is connected to our router as below:
Client ip address: 192.168.100.2 VLAN 110: 192.168.100.3
access-list 110 permit tcp host 192.168.100.2 host 192.168.90.15 eq 8080access-list 110 permit icmp host 192.168.100.2 anyaccess-list 110 deny ip 192.168.100.0 0.0.0.255 ? I was unable to access the webserver even after many attempts.
Cisco Catalyst 2960 series,i want do a SNMP request over OID. When the output should be like this: Portnumber and VlanID. Is there a OID for this output?
I just bought a SG200-18 in order to use LAG between a backup server and multiple computers and servers. Servers are supposed to all use 2 links and computers only 1.
As soon as I activate LAG on port 2 and 3, no matter what is connected on the switch I lose access to the switch interface (luckuly, it's still working on port 17 for a strange reason) and all computers / servers connected are randomly losing the network access. Everyrhing start to be slow but most servers and computers don't lose access to the internet. Browsing a web site will suddenly take ages but... it will work eventualy.
I already used LAG on other switch without a single issue.. The only uplink I have is to the router and I know that I don't have any issue with network cables....
So what am I doing wrong ??? I didn't even try to configure the TEAMING on the servers, just creating LAG on the switch will kill everything Oo.. I'm starting to think that my SG200 is dead out of the box.
I have a Linksys SGE2000 Switch and I've been trying to get Vlan's to work.How I'm trying to setup is like this
Port 1 - Vlan22 - Plugged into trusted port in firewall Port 3 - Vlan25 - Plugged into DMZ in firewall Port 15 - is plugged into a VMWare host. The network is setup as production is Vlan 22, DMZ is Vlan 25. Port 16 - Internal server so is Vlan 22
Both Vlans have a different IP subnet.I think I have port 3 configured ok as it's only one Vlan. I'm trying to get Port 15 configured properly and it won't work.Servers on VMWare hosts are Windows Server O/S.
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
I am trying to configerate static switchports on our nexus 5548 (nx-os 5.1(3)N1(1)) over snmp.The support-list url... states that the CISCO- VLAN- MEMBERSHIP- MIB is supported.I can read the information, but if i try to set vmVlan or vmVlanType i get the message: "SET failed. ("ip-address"). Information: Not Writable."I can use set_request in general (e.g. CISCO-CONFIG-COPY-MIB). how to set the vlan and vlan-type over snmp?
I have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
I have a number of class-'c's as a hand-off from my data center fiber to my 2960, which then sprawls the racks with about many 2950 switches, mostly 20 machines per switch. To allow machines on one 2950 to push data to another 2950 without routing back to my ISP's router(which costs money for bandwidth) isn't is possible to trunk one port on each 2950 to another 2950 and adding a addititional vlan8 to them. Then data jumps from 2950 to 2950 without going back to the 2960 or mainly not going back to my ISP's router. Is this the correct way to accoplish this with extra vlan and trunking the 2950's to each other or am I looking at this all wrong?
how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
we are trying to do an automatic backup of our switches config trough snmp.my script can easily backup cisco 2950-2960-3550-3560 using snmp.but I dont know the mib to use to backup the cisco small business serie 300 switches.
I have been trying, so far unsucessfully, to trigger backups to a TFTP server of our SGE201 switches. I have testesd TFTP backups via the web interface, and that does work. I need SNMP as I need a scriptable method to trgiger the backups on a regular schedule. I am running the SNMP query from a RedHat Linux server. So far I have the following query work out, but it is failing: [code] The error I am getting is generic, and the same query failed on multiple switches running Software Version 3.0.0.18. The switch is set with the community having full SNMP-admin access from the server's IP address.
I was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
Im sitting with a few cisco sf-300 24 switches and i'm trying to get the Mac-addresses the switch have learned from each computer connected to the switch.
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
