I have Linksys SPS224. I've learnt how to change some parameters through SNMP. But this changes are applying to running-config, and, when switch reboots, all loose.
How can I save this changed running-config to startup-config through SNMP?
I have Linksys SPS224Trying to create VLAN through SNMP. Issueing the string to create VLAN ID=100 with name "VLAN100"
snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.100 s VLAN100 .1.3.6.1.2.1.17.7.1.4.3.1.5.100 i 4
It reports
Error in packet.
Reason: (genError) A general failure occured
Failed object: iso.3.6.1.2.1.17.7.1.4.3.1.1.100
In same time changing the name of existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.23 s VLAN23 and even deleting the existing vlan snmpset -c private -v2c 10.254.2.144 .1.3.6.1.2.1.17.7.1.4.3.1.1.510 i 6 are successful.
How can I create new vlan through SNMP?
I have ASA 5505 and I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
View 8 Replies View RelatedI have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
[code]...
I am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies View RelatedI have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.
I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in: "Building configuration... [OK] -> NVRAM Verification Failed".
my Cisco ASA 5510 doesn't save the configuration to the disk.
View 1 Replies View RelatedI have a 2801 running c2801-spservicesk9-mz.124-3g.bin According to the Cisco IOS MIB locator the image supports OLD-CISCO-SYSTEM-MIB I have tried .1.3.6.1.4.1.9.2.1.55 etc to set server IP address and the filename string but without any luck.e.g.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.2.1.55.a.b.c.d (where a.b.c.d is the server IP)
I have also tried the method similar to that for Cat 3550 switches where you create a table of entries to define the transfer paramaters then activate the transfer (I think the CISCO-CONFIG-COPY-MIB)
e.g.
[URL]
C:>snmpset -v 1 -c private <device name> ccCopyProtocol.<random number> integer 1 ! 1 = tftpccCopySourceFileType.<Random number> integer 1 ! 1 = networkFileccCopyDestFileType.<Random number> integer 3 ! 3 = startup & 4 = runningccCopyServerAddress.<Random number> ipaddress "<server ip address>"ccCopyFileName. <Random number> octetstring "<file name>"ccCopyEntryRowStatus.<Random number> integer 4 ! 4 = createAndGo, or 1 = Active
To write net have the source as running (4) and the dest as network (1)
ccCopySourceFileType.<Random number> integer 4
ccCopyDestFileType.<Random number> integer 1
Clean up at the end - destroy .14 with the value of 6.
example output : -
-- earlier output omitted --
Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.4.111
Error in packet.
[code]...
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies View RelatedI'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
View 1 Replies View RelatedAny snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedDoes the power save feature of the SG 102-24 can be disabled somehow ? Our college just purchased 24 of these switches. We are having a problem with the switches affecting some of our monitoring software (Vision from Nettop).Basically, the client pc's become invisible to the master station. I believe this is due to the ports doing an automatic shutoff.I know these switches are unmanaged, but I'm hoping they at least have some form of configurability. Right now our only option is to have an instructor cycle the power of the switch to get the client pc's visible again.
View 3 Replies View RelatedI need to SNMP on Cisco Smart switch SF-200 24p. I cannot find any option on administration to turn snmp service on.
View 2 Replies View RelatedI am using a couple cisco sg300 28P switches along with a sonciwall firewall/router. The sonicwall was already in place and working so they didnt want to replace it. I understand how to configure the vlan on the sonicwall, but could use some info on the cisco. I would basically like to create 3 vlans, 1 default for management, 2 for pc's on lan, and 3 for the cisco spa504g phones/'voip. Would i just go into the vlan managment, configure the 2 new vlans and give them two id's? These offices have one network drop, so the phones and pc's will be sharing the switch ports, however the phones have a setting to configure the vlan id so they know which one theyre on. Is there anything i need to do after that? I want to make sure that vlan 3 has the highest priority becuase its voice, is there some qos configurations i need to make on that switch as well? Also, the port that links the two cisco swtiches together, does that need to be set as "trunk" port? I understand what vlans are, but its just the first time ive run into these cisco models. .
View 0 Replies View Relatedi need supports for how can config SLM224P with UC540.
View 1 Replies View RelatedI'm playing with an SF300-24P switch and want to connect an IP Phone. I'm more familar with IOS syntax than the SF300 GUI.
How would I replicate the following in the SF300:
Switch(config)#int fa0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 15
Switch(Config-if)# switchport voice vlan 5
Not sure if setting the port to an ACCESS port on VLAN 15 (i.e. 15UP) and having the Voice VLAN set to 5 is correct.
Or should the port be set to General or Trunk with 15 as the untagged VLAN and 5 as the tagged voice VLAN (i.e. 15UP, 5T)?
how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
we are trying to do an automatic backup of our switches config trough snmp.my script can easily backup cisco 2950-2960-3550-3560 using snmp.but I dont know the mib to use to backup the cisco small business serie 300 switches.
View 6 Replies View RelatedAm I correct in thinking that 200 series swiches now support SNMP using v1.3?
View 1 Replies View RelatedIs this known bug that you cannot backup (export) full running or startup config from this switch? Will this be fixed in next firmware? (btw, still no new firmware with CDP support for this script altough sales literature mentions that it should have already been available...)Switch does let you backup configuration as text file (which looks similar to normal IOS config syntax), but it doesn't contain all settings so the file is pretty much useless to restoring the config to another switch.At least following settings are missing from the file:
- management interface config (including DNS settings)
- passwords
- remote syslog server config
- SNTP server config
- IGMP config
- LLDP config
I have a small doubt with Nexus 7k,5K,2k & 1K.We want to backup the running config to my desktop through tftp.When i tried to backup from Nexus switches showing like below Nexus 7K. [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config Vdc-all". [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric"
It's showing three choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric" or "copy running-config startup-config vdc-all". [code]
I have been trying, so far unsucessfully, to trigger backups to a TFTP server of our SGE201 switches. I have testesd TFTP backups via the web interface, and that does work. I need SNMP as I need a scriptable method to trgiger the backups on a regular schedule. I am running the SNMP query from a RedHat Linux server. So far I have the following query work out, but it is failing: [code] The error I am getting is generic, and the same query failed on multiple switches running Software Version 3.0.0.18. The switch is set with the community having full SNMP-admin access from the server's IP address.
View 3 Replies View RelatedI was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
Im sitting with a few cisco sf-300 24 switches and i'm trying to get the Mac-addresses the switch have learned from each computer connected to the switch.
View 2 Replies View RelatedI have two 4506 switches in my organization. Recently the office was relocated and when both the switches were booted they ignored the startup config.The config-reg was set to 0x2101. No boot system command was configured.So I changed the config-reg of SW1 to 0x2102 and gave boot system command as stated below.When reloaded the switch booted to ROMMON and I had to manually boot the IOS.I want them to boot normally with IOS.Config of SW2 is not changed since relocation. I am specifying both configs bor your consideration. [code]
View 12 Replies View RelatedAny snmpset commands to modify port vlan membership on SG300-28 switches? I checked [URL] however this information is apparently only valid for catalysts.
The latest firmware is installed and the provided MIB files are used.
I am trying to track down the SNMP MIBs for the Linksys by Cisco SRW2048. Please note that this is the model before the complete CISCO rebrand of the product. I have SNMP walked, browsed etc etc and I just can't pull CPU and RAM usage. Any working view of those two stats? I'm using OpManager by ManageEngine as my NPM platform.
View 1 Replies View RelatedI want to enable SNMP and track the status/ of the interfaces in switches.
We have Two- cat 3750 (L3 switch) and Nine-cat 2960 (L2)
How to configure the SNMP. any Links provides the required info with an example of configuring snmp will be really useful.
we have OPEN NMS, SPLUNK, MYSQL monitoring tools.
I've got an SG300-10 connected back to back (trunked) with a Cisco 3560X switch, across a fibre link and am seeing some big inconsistencies in terms of unicast data transferred across the ports between them.
During a night time window of 4am - 6am I run backups which involves a large copy of files, that almost saturates a GigE link - we can see from the 3560X end that the link is running at a bit over 800MBit/sec of throughput, sustained. The duration of this transfer is consistent with the size of the files being transferred (ie just over an hour, and is what I'd expect for a data transfer of about that amount). Back-of-the-envelope calculations indicate that the 3560X is measuring this data throughput correctly.
However on the SG300 end of the link, which is also being polled by the same application (Cacti), I'm observing spikey counts of only around 20MBit/sec during that window. These counters are very obviously incorrect - there's a huge amount more data moving across the port than that. The incorrect calculations are showing on both the trunk port out of the SG300 (uplink) as well as the interface where the NAS is connected in (which is an access port).
Cacti is polling the OID: .1.3.6.1.2.1.2.2.1.16.57 which translates to IF-MIB::ifOutOctets.57 = Counter32.I'm running version 1.3.0.62 but this problem is not new to this release - previous releases and 1.2 based releases also had this problem.
It looks like multicast traffic may be being counted correctly (that's only a suspicion though), however what I am certain of is that there is a very large discrepancy with the unicast traffic counts.Is this OID the correct one to be using for this switch?
I have a scenario where 15 c500 switches and 5 2960 8 port switch connected to 4507R core switch. There are 10 dhcp pools created on the 4507.
Eg: ip dhcp pool XXXX
network xxxx.xxxxxxx
default-router x.x.x.x
Now the default router is directed to vlans created on the switch i.e vlan 101, 102, 103 and so on. Now the remaining switches connected are configured to be in the same vlan. So the systems connected to the edge switches will get the DHCP ip automatically, Now my problem is after sometime (may be 2 or 3 hrs) all the edge switches are losing configuration automatically even though it's not restarted, even after saving the config on to nvram, everytime I connect the console and check all the saved config is lost?
I cannot open the config page of beetel adsl2 router using 192.168.1.1I have connected my laptop to router via Lan cable. Now when I give the ipconfig, I get some random IP and does not get the default gateway: Autoconfiguration IPv4 Address. . : 169.254.129.188 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . :I cannot ping 192.168.1.1 nor 169.254.129.1 thus the web page of router cannot be opened.This all happened after I reset my router.
View 3 Replies View Relatedwhich models of HP ProCurve or Dell PowerConnect support 64-bit IF-MIB counters, or for that matter any other manufacturer (Zyxel?) (snmpv2 or v3, OID .1.3.6.1.2.1.31.1.1.1.6)I believe pretty much any Cisco Catalyst above a 2950 do, however don't believe any of the SG series do. I realize I could pick up a 2960G for $1500-2k and be good to go, but I forsee a larger switch purchase in the future, but still could use a switch in the meantime that was able to allow accurate monitoring of closet uplink bandwidth?
View 1 Replies View Related