I am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies
I have ASA 5505 and I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
View 8 Replies View RelatedI have Linksys SPS224. I've learnt how to change some parameters through SNMP. But this changes are applying to running-config, and, when switch reboots, all loose.
How can I save this changed running-config to startup-config through SNMP?
I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
[code]...
I have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.
I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in: "Building configuration... [OK] -> NVRAM Verification Failed".
my Cisco ASA 5510 doesn't save the configuration to the disk.
View 1 Replies View RelatedI have been working with the 871 router and configuring it for work at home users. Now we are purchasing and using the 881's instead. I noticed that after write erasing the router, I need to run the command in the global config "license boot module c880-data level advipservices" just have eigrp.However when I type show license, I get the following:
Index 1 Feature: advipservices
Period left: 8 weeks 3 days
Period Used: 2 hours 55 minutes
License Type: EvalRightToUse
[URL]
There is more but I left it out. However it shows that the advipservices license has only 8 weeks and 3 days left.What is this? I thought that when I buy a brand new router, I should get everything, including IOS licenses. So I would like to know is this a new licensing scheme and how does it get register and how do I get it so that the advipservices license is permanent?
How do you save the command output from the CLI to a file on flash?
With IOS, I would normally use a pipe command to redirect to tftp, but the ASA doesn't support this as far as I can tell. As a work around I was thinking I could save the output to flash and then tftp that file off the ASA.
Is there a good reference in how to interpret the "show AP stats" command?
I have a new (online for 15 days) 1142 listed below. It is the first 802.11n AP I've deployed. The stat counters look bad [code] But I don't know how to put it all together to say "here are the stats, this is the problem". I see TxFrameCount, but no corresponding RxFrameCount, so it is hard to calibrate some of the errors. [code]
I got trouble when tried to save configuration by 'write memory' command.
cisco WS-C2960-48PST-L (PowerPC405) processor (revision G0) with 65536K bytes of memory. Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(52)SE,RELEASE SOFTWARE (fc3)
Cat2960#wr
Building configuration...
% Warning: Saving this config to nvram may corrupt any network management or security files stored at the end of nvram.
Continue? [no]: no % Configuration buffer full, can't add command:
After this message continue typing "yes" sometime that switch reload all times. The service compress-config command is not available anymore.
I have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies View Relatedmy environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
I am looking to replace the active supervisor (S720-10G) on our 6509E running in SSO mode. The new module already has the same IOs version as the standby supervisor.Once I have swapped the module how do I know that the config has sync'd correctly other than checking the logs? Is it a case of looking at the "Redundancy Mode (Operational)" state and ensuring is says SSO?Also, is there a command that will force a config-sync if it is running in a mode other than SSO?
View 1 Replies View RelatedIf i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedI have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
I have a new wireless router which I have hooked up successfully to 3 computers , a playstation, and a WII on a secure network. My fourth computer refuses to save the new key. Ii keeps defaulting to an 8 digit number. It shows the secure network on availiable networks but won't accept the WPA key.
View 1 Replies View RelatedCurrently the guest wireless users are maintained by WCS 7.0.172.0. I'm having a project to set up another 5508WLC in one location to replace the WLC in use in different location. My concern is regarding the guest user accounts. Can I use the feature of "Save Guest Accounts on Device" in WCS to save all the guest accounts on another WLC? I tried this feature and I got the message of "Successfully saved Guest users to the following respective controller(s) where they were applied". I don't know if it is because there is currently only one WLC in the WCS or the account can only be saved on the original controller where it was created.
View 1 Replies View RelatedI'm just trying to port forward with this router, and after I'm done entering all my settings, I click save settings, it tells me settings are successful.
But the it goes back to the port forwarding page and all the stuff is at default again as if I didn't make any changes. What the hell is this?
I'm sure it's just a little something I don't know about that's making it not save any changes to port forwarding.
I have Cisco AP 1142 standalone and I want this one to operate with WLC.
I have searched in Google, they said I need to upgrade AP1142.
I don't know how to upgrade it.
i have a problem using my usb to serial cable connection, i can connect to one router on my work, but i can't connect to AP 1142, (i have tested also con AP 1231).i have a laptop running windows 7 64 bits, before i use a win xp 32 bits, and i didn't have problems.i am using putty, and have installed tera term 4.74 but the same.connection details, 9600, 8, 1, N, N.
View 5 Replies View RelatedI can't get connectivity from laptop to AP using cross over or straight through cable to do a tftp transfer from tftp server on laptop to ap.
I held the mode button on ap and powered on to get to rommon. The ap has no ios so it goes to rommon anyway. ap light is blinking red.
ap: set
DEFAULT_ROUTER=10.0.0.1
IP_ADDR=10.0.0.1
NETMASK=255.255.255.224
[Code].....
After AP is booted it shows the following message and cannot able to join in WLC:
*Mar 1 07:13:37.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.71.16 peer_port: 5246
*Mar 1 07:13:37.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
I have a problem when trying to configure my wrt320n , I put in the exact same config. as I had with my wrt54g, and I do mean the exact same, even the name and all, but when I try to save the config on Advance Routing I get the message "Invalid static route", I think it's a bug
View 9 Replies View RelatedI just converted AP 1142 to LAP using the image "c1140-rcvk9w8-tar.124-21a.JA2.tar".
The WLC is a 5500 with 2 NIC : one on 192.168.0/24, one on a specific vlan 10.20/16
The main management interface is on 192.168/24 but we defined as management the interface on the 10.20/16 network.
For the access points, we use ports on a native VLAN on 10.20/16 with other available VLANS which are used for the wlan networks
We have 1152 APs which work fine on this config but that needed to be registered on the 192.168/24 network, then we moved them in their VLAN 10/20/16 and they work fine.
We also have 1142 APs which have been upgraded to LAP. These AP do not work with our architecture. They register correctly on the 192.168/24 network, but do not give access to the wlan VLANs. If they are moved in the 10.20/16 network, they don't register to the WLC (message : Timed out while waiting for ECHO repsonse from the AP). The AP do not get an IP.
is there a restriction with VALNs on these AP ? or is something false ?
I have an 1142 AP that I am unable to set back to factory defaults.Here is what I have done so far:
- boot AP while holding down the mode button
- ap: delete flash:private-multiple-fs
- yes
- ap: boot
- when the AP boots fully I try and enter any lwap ap commands and get "ERROR!!! Command is disabled"
- the AP name and password were reset to defaults but I am unable to get the IP address cleared.
I've also tried "clear lwapp private-config" and get an error saying the command is disabled.
I need to convert some 1142 APs to lightweight mode. They will connect to controllers running 7.3.101.0. I noticed there's two options of Lightweight IOS code available c1140-k9w8-tar.152-2.JA.tar and c1140-rcvk9w8-tar.152-2.JA.tar. Whats the difference between the two versions of code?
View 4 Replies View RelatedWhen we take a look at the internal antennas on the 1142 AP, we notice the 5ghz pointed all the same way, but for the 2.4ghz we can see each offset by 45/120 degrees. It was my understanding that all antennas are omnidirectionals on the 1142, why are those 2.4ghz antennas not all pointed the same way? onfiguration advantage and that each antenna is indeed omnicadirectional? Example, if I shut just one antenna off, do I lose a sector (120degree)?
View 5 Replies View RelatedI recently purchased another 1142 AP to expand out our current wireless infrastructure, my question is, what exactly needs to be done for this to work so that users can roam freely and auto-connect to the closet AP with the best connection without getting disconnected?
I have set all the settings the exact same on the new AP to match the existing AP. (How to save the configs into a file would be great, I am not sure how to do that)... But anyhow, before I launch it, I would like to be sure I am correct so I do not bring down the existing network. Of course, the only difference between the 2 are the IP addresses. AP1 is 192.168.2.2 and AP2 is 192.168.2.3
All computers are using Linksys Wireless-N cards.
The last three new APs I have received from our supplier (official Cisco 1142 LAPs) have all successfully connected to our 4400 series WLCs but are all reporting as being in an Operational Status of 'Down' ie their A/B/G/N radios are not broadcasting even though the APs are all in an enabled state. Furthermore, there is no steady green light showing on the APs - there is no light showing whatsoever (although they were displaying the familiar red-orange-green lights while they were pulling down the IOS images from the WLCs).
The only strange thing I have noticed is that in the AP config screen, the ‘Mini IOS version’ is shown as being v7.3.x. The other – working APs – we have of the 1142 series show v3.x. I know that controller code v7.2 and above only work with the newer 5500 and 7500 series WLCs. Could this be the issue and have any of you seen this issue previously? I am running WLC code v7.0.230.0.
that cisco ap 1142 will support WLC2506 or not .
View 2 Replies View RelatedI have WLC 2540 and AP 1142..i have configure them both and got connected(WLC can detect the AP) yesterday then i turn off them both and now when i powered up , the WLC cant detect the AP but AP and WLC can still ping each other they communicated at layer 2, both WLC and AP in one IP segment.
here some debug from AP
*Jun 21 13:49:47.784: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.3.2
*Jun 21 13:50:05.913: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceed., 1)x(UNKNOWN_MESSAGE_TYPE (5)
*Jun 21 13:50:05.913: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jun 21 13:50:05.913: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10. 0.3.2:5246
*Jun 21 13:50:05.954: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jun 21 13:50:06.042: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[code]....
About every 20 minutes 12 of 300 APs keep rebooting. I have tried moving them to different controllers. I have tried downgrading the code and then upgrading the code. I have tried replacing the AP. I have tried swamping out cables. They are all connected to a 3750 stack but plugged into different switches in the stack. Here is the result that I could capture when I saw it disconnect from the controller. This is the output from the AP:
DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.100.40.212:5246
*Jul 28 14:33:19.595: %WIDS-5-DISABLED: IDS Signature is removed and disabled.
*Jul 28 14:33:19.597: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jul 28 14:33:19.597: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jul 28 14:33:19.655: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[ code].....
I have removed the ip addresses for security reasons.
I am a bit confused of the repeater functionality in the mentione AP, my concerns are:
1- Will each radio be dedicated to one function (for example 2.4 GHz for user access and 5.0 GHz for repeater functionality)?
2- Will the internet speed for users be affected when using the access point in repeater mode (no ethernet)?
3- Can an Autonomous AP function as a repeater?
4- Is there any license required?
5- What is the signal overlap requirements between the two Wired and non Wired AP?
6- Can the non wired AP be work as a repeater for another non wired AP (similar to cascading)?
