I have a new wireless router which I have hooked up successfully to 3 computers , a playstation, and a WII on a secure network. My fourth computer refuses to save the new key. Ii keeps defaulting to an 8 digit number. It shows the secure network on availiable networks but won't accept the WPA key.
View 1 Replies
How do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies View RelatedI'm just trying to port forward with this router, and after I'm done entering all my settings, I click save settings, it tells me settings are successful.
But the it goes back to the port forwarding page and all the stuff is at default again as if I didn't make any changes. What the hell is this?
I'm sure it's just a little something I don't know about that's making it not save any changes to port forwarding.
I have a problem when trying to configure my wrt320n , I put in the exact same config. as I had with my wrt54g, and I do mean the exact same, even the name and all, but when I try to save the config on Advance Routing I get the message "Invalid static route", I think it's a bug
View 9 Replies View Relatedi am trying to port forward my router so that i can run a minecraft server. When I put in th port number and save the changes, it brings me to a screen that says my changes have been saved yet when i go back to the page they haven't. I have tried deleting the cookies on my browser, using another browser, using another computer, and hard resetting the router for ten seconds. None of this works.
View 2 Replies View RelatedI am in the process of upgrading a Linksys WRT160Nv2 to a Cisco E4200. I run Cisco Connect and enter my ISP password (7 characters long) and click save but when it refreshes the screen, the password field has 16 characters in it.
View 4 Replies View RelatedI did read the thread entitled ''WRT160N Can't save settings'', but I believe this might be different. My router is actually communicating with my computer (physically plugged in), since I can save all other settings EXCEPT the port-fowarding ones.I am trying to save settings for a gaming application in the Single Port Forwarding section of my router settings. After clicking both ''save settings'' and ''continue'', it simply returns to the Single Port Forwarding section, except everything is blank, as though nothing was saved.
Here are my specs:
WRT160Nv1
Firmware Version: v3.0.03
Here are the steps I have already undertaken:
1- Erase browser cache and cookies
2- Updated to latest firmware (v3.0.03), 10-second reset button, 20-second power cycle.
I just installed my new E4200, and am setting the Access Restrictions. Is there anyway to block the popup window that displays every time I enter the form or save the settings?
I'm using IE9 and have tried adjusting the Popup Blocker, but to no avail.
I have Verizon service for all 3 TV., Fios, and phone. I was told I need to keep their router for my cable service. It is a weak G router. I bought a Cisco E1000 Nband router. Turns out the IP address for both is 192.168.1.1 When I try to access my router, it automatically goes to the Verizon router.How can I get to the Cisco router? Aside from ,resetting it and running the setup disk?
View 1 Replies View RelatedI am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 4 Replies View RelatedI own a E1000 router that I use with several wireless machines. Unfortunately, I cannot connect to the configuration of the router by typing url...in a browser, be it wireless or weirdly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router". I tried to switch my router off and on, but that doesn't work. Totally resetting the router solves the problem, but not definitely.Is there a solution that does not require resetting my router?
View 2 Replies View RelatedMy guest can't use my wireless network and I can not add more devices like a ipad2. Got a new ipad2 for my son for Christmas been trying to set it up for Christmas, so on Christmas day I am not trying to do the set up. My problem is I can not get it to log on to the network. I have been putting in the same pass word all my other computers in the house use but it will not work...
View 2 Replies View RelatedMy wireless router (E1000) was accidentally unplugged. Since then the wireless LED light doesnt come on and the router cannot be detected. All the other lights are on. I tried to reset it but I dont think it worked, since the power LED didnt blink as its supposed to do after holding reset for 10-15 seconds (or more!!).
View 5 Replies View RelatedI've been using the E1000 for months. I have 2 iphones, an ipod, a windows 7 netbook and a macbook connected wirelessly to it. It's been set at wpa2/wpa mixed mode all this time without a problem. Out of the blue: no wireless connection on any device. I restarted the modem, router, PC's, phones, etc. I've updated the firmware. The only way I can get a wireless connection is to use wep. How can I get the better security and speed of wpa2 back?
View 4 Replies View RelatedI am trying to access the internet with my ipod and it is picking up my wireless connection but it is asking for a password, how do I get my password. I don't remember seeing a password when I hooked up my router several months ago. I called Cisco for some technical support but they wanted money to get me and I am not paying them a dime.
View 1 Replies View RelatedI can setup my router with the cd
View 1 Replies View RelatedI have a PS3, and i play allot of video games such as all COD game especially MW2. It says i have a strict or moderate NAT. My router is in the same room as the PS3, so i should have a Open Nat.Also i have another question, i bought this Epson printer from Best Buy, i was wondering if I can connect to it Wireless, but i think i cant connect to it wireless cause i dont see the WiFi Certification on the printer or anything hints that it can connect wireless
View 9 Replies View RelatedWith the E1000 tthe wireless devices they seem to work just fine, I can access the internet just fine.
For my desktop PC in oder to use the router to get on the internet or to even use the Cisco Connect to check the router, the E1000 needs to be rebooted. I am unable to access the router otherwise. I have tried 3 different LAN cards all with the same results.
The latest firmware notes do not look like upgrading the firmware will work. My Router info from Cisco connect
Model name: Linksys E1000
Model number: E1000
Serial number: CVN21L422937
Firmware version: 2.1.01 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): unknown
Things seem to slow down significantly to the point of loosing connectiviety. When I check, my mips are 150 or so. Tried disconnecting and connecting again but didn't work. When I power down the router and power it up, I get 300 mps again but doesn't last too long
View 2 Replies View RelatedA lady gave me E1000 along with an IMB Thinkpad because her husband was the main user on the internet. I have an intel iMac 10.4.11, DSL. I have not yet connected to either device via the router. I am new to wireless routers. I have been to the configuration page
View 2 Replies View RelatedI have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies View RelatedI had an E1000 for a couple of years that worked OK. Then it went nuts--sporadically dropped the signal, wouldn't show its web page, etc.--maybe a power surge, who knows? So I tossed it and got a new one on the theory that it would be a plug in replacement .The new unit had a good signal, but also wouldn't show its web page, so I couldn't configure security. I removed Network Magic and everything else I could see pertaining to the old unit. However, the CD for the new unit still gives me: " Your router has already been set up. You need to use an Easy Setup Key that you can use to get other computers connected." Needless to say, I don't have such a thing. Cisco Connect is not installed at this point, so I can't go into it to create one.How can I purge the remains of the old unit so the new one will install properly?
View 6 Replies View RelatedI have E4200 connected to Internet. It is configured with NAT. My side of the router is set to 10.10.10.0 and DFG is set to 10.10.10.254. Server is connected at 10.10.10.1 and is DHCP host.I now have E1000 that I want to connect downstream side of the E4200 (located on the other side of the building). I want the E1000 to be an extension of the existing network so the whole building looks like one network. I'm not sure how to configure the E1000. I assume I need to disable NAT but I'm not sure how to configure the Internet IP addresses of the router and nro am I sure how to configure the local network side of the router.As I write this, I wonder if I connect one of the Ethernet ports of the E1000 to the E4200 and just leave the Internet side unplugged?
View 2 Replies View RelatedI'm trying to set up my E1000 router and when I run the Cisco Connect software that came with the router I get a message that says that it can't find the router, I've tried running it with my computer connected to the router and not connected. I've looked through the FAQ section and didn't really find anything. I'm trying to set it up on a laptop, it's a Vaio running Windows 7, I don't if that makes any difference.
View 7 Replies View RelatedI am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 2 Replies View RelatedI've been searching off and on for the past couple months trying to figure out what we could do to our router to open our NAT, after having both the PS3 and Xbox 360 tell me I've got moderate NAT. I tried a DMZ with my PS3 having a static IP, I tried UPnP. I messed with firewall settings, to no avail.
I recently found something that did work however, on Google. Basically what happened was, I needed to reset the router and change a few settings on top of enabling UPnP I didn't know about(CTS Protection, remote management) how they could have anything to do with translation of data.
But like I said, after doing a huge step by step walk through, I was able to get open NAT in the network tests of both PS3 and 360(even though the PS3 obviously still says Type 2. It used to say Type 2, but it also used to have an error code at the bottom of the page). I've checked in games on each console, and they tell me I've got open NAT.
Now I still have one tiny problem. Red Dead Redemption. I play Red Dead Redemption online with two friends(who, incidentally, have the same router as me), and we haven't been able to communicate if we were using routers. We still can't, but I'm thinking that it's not my router anymore. I'm thinking his router has incorrect settings. Am I correct?
I try to make changes or save changes from the web page on my BEFSR81 nothing changes and everything revert back to the original setting made a long time ago. cancel changes works fine as the page reloads, but save changes won't make it save or reload the page with saved settings. i updated java and used 3 different browser and always get that error.
View 1 Replies View Relatedmy new laptop is asking for pin number: i have a wrtter54g2 v1 router.... can't find pin number
View 9 Replies View RelatedMy new laptop is asking for pin number I have a wap4410n.
View 1 Replies View RelatedI have recorder my Security Key number incorrectly, how can I get the correct key number? This is for a Wireless-G router WRT54G2.
View 2 Replies View RelatedI was trying to set up my cisco e1000 it always says "Enter router password" what is the default password...
View 9 Replies View RelatedMy router has recently stopped broadcasting wifi, unfortunately it also no longer lets me use it as a router to get internet. if i plug directly into the modem i can get internet. but while using the router i get a computer symbol with an explanation mark on it
View 1 Replies View RelatedI upgraded my Mac OS to 10.7 (lion). I can no longer use Cisco Connect. I cannot recall the password I created when using Cisco Connect prior to upgrading to Lion. Is there any way to determine or reset my password without Cisco Connect. And why is it taking Cisco so long to provide firmware that works with Mac OS 10.7?
View 3 Replies View Related
