Linksys Wireless Router :: E1000 - Save / Copy Configuration Entries Onto Flash USB Drive?
Jul 7, 2011
How do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies
ADVERTISEMENT
Sep 4, 2011
I have a new wireless router which I have hooked up successfully to 3 computers , a playstation, and a WII on a secure network. My fourth computer refuses to save the new key. Ii keeps defaulting to an 8 digit number. It shows the secure network on availiable networks but won't accept the WPA key.
View 1 Replies
View Related
Apr 5, 2012
I've been experiencing a strange, repeatable behavior with my Linksys E1000. I have several wireless and wired devices connected to my E1000:
Wired: TivoHD, Sony BluRay Player, Sony TV, Windows XP Wireless: Lenovo Laptop (Windows 7), HP Laptop (Windows 7), 3 iPods, 2 iPhones
When I try to copy large files (~ 4GB) from my (wired) Windows XP box to either of my (wireless) laptops, the Linksys drops my WiFi network -- but the wired connections continue to work (including internet access). Copying the same/similar file from a WiFi device to a wired device appears to work correctly, as does copying from WiFi to WiFi.
To be clear, my WiFi network "disappears" -- it is no longer listed as an available network (as opposed to just dropping internet connectivity for WiFi). Unplugging the router and plugging it back in brings my WiFi network back up.
I have been able to repeat this issue with multiple files over the course of several weeks, and it happens about 75% of the time (i.e., I am occassionally able to complete a file copy from wired LAN to WiFi).
A little bit of background: I resurrected an old Windows XP box and am using it for shared network storage. I copied about 400 GB of files from my laptops to the XP box (WiFi to wired) with no issues at all. Pulling the same files back from XP to my laptops (wired to WiFi) has been causing the issue described above.
View 1 Replies
View Related
Jul 19, 2011
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies
View Related
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
Jun 19, 2012
I have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies
View Related
Jul 25, 2011
My router does not have a usb port. So what now?
View 1 Replies
View Related
Apr 18, 2011
I am having a problem with copying files onto my Storage device Connected to my WAG320N, the router is up to date with the latest updates and has been reset in an attempt to overcome this problem. I currently have attached a 2TB Seagate External Hard drive plugged directly into the router formatted in NTFS, and using Windows 7 Bit to access the Routers Webpage and the External Drive.
I am able to set up permissions and access control all okay, so some users can see some folders or have access in Read only or Read and Write Permissions, however I have been using the Admin account when accessing the drive which has Read and Write permissions to all Folders on the Drive. I can create a new document on the Drive (Right click > New > .Docx or .txt) and save file successfully and can view from other computers from the network, however I cannot Copy from any of the computers to the Network drive (e.g.. Copy .txt file from Computer to Network drive), I get the Windows Transfer Dialog and it Calculates Transfer Rate for a while before telling me it's unable to and that I can either select Try Again which comes up with the same error message, or Cancel the transfer.The reason why I want to be able to Copy files to the Network Drive is so I can centralise all the Photos, Videos and other files and documents to be shared to all computers on the network.
View 1 Replies
View Related
Feb 6, 2011
When I try to copy ios to one flash in router 2801, I receive the message of of insufficient memory, and have the follow out in the next command: [code] This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
View 6 Replies
View Related
Dec 3, 2012
how to storage the DHCP IP table in a external flash of a router. This is because the router is switched off and switched on everyday but I want that it remembers which MAC is associated with which IP when it starts again and avoid IP duplicate problems. The command "lease" doesn't seem useful here.
View 4 Replies
View Related
Jan 8, 2013
I just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin
Source file name []? asa804-k8.bin
Address or name of remote host [192.168.10.2]?
Destination file name [asa804-k8.bin]?
Writing file tftp://192.168.10.2/asa804-k8.bin...
!%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect)
Cisco asa#
View 3 Replies
View Related
Feb 24, 2012
I have a really stupid problem with my RV042. The main logon password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.Am I missing something glaringly obvious? I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.
View 2 Replies
View Related
Feb 20, 2012
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error. [code]
View 3 Replies
View Related
May 28, 2012
How do you save the command output from the CLI to a file on flash?
With IOS, I would normally use a pipe command to redirect to tftp, but the ASA doesn't support this as far as I can tell. As a work around I was thinking I could save the output to flash and then tftp that file off the ASA.
View 5 Replies
View Related
Feb 1, 2012
I deleted the flash from an ASA5510. I was able to tftp a version back into the device, but cannot seem to correctly have the box boot from this flash. I get the following error:
!WARNING: BOOT variable added, but not a valid image disk0: /asa831-k8.bin
*** Output from config line 41,"boot system disk0:/asa83..."
I have tried every save syntax i can think of to save this flash, but have yet to have it boot with an image ( I keep booting into ROMMON and have to tftp the image back in)
View 5 Replies
View Related
Oct 7, 2012
I have Cisco 2800 series router. When I am trying to write memory getting error message " Error opening flash:config-backup-1 (No more root directory entries available)" When there is simultaneous access to a router's NVRAM, we might encounter these errors. In order to clear the line the other user(s) is (are) connected on and free the NVRAM, issue the clear line command. But still getting the same error message.
View 1 Replies
View Related
Nov 9, 2011
Is it possible to use the USB ports on a ASA5510's to copy files onto the flash?
I have not been able to find any ionfo on this in the users guides ?
View 2 Replies
View Related
Jul 9, 2012
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies
View Related
Jul 27, 2011
I m unable to take backup of Switch c2960 using
#Copy flash: tftp
while i m taking it show some error
t#copy flash: tftp:
Source filename []? c2960-lanbasek9-mz.122-44.SE6
Address or name of remote host []? 10.23.120.15
Destination file name [c2960-lanbasek9-mz.122-44.SE6]?
%Error reading flash:c2960-lanbasek9-mz.122-44.SE6(Is a directory)
sh flash:
Directory of flash:/
2 -rwx 1919 Mar 1 1993 10:27:17 +05:30 private-config.text
3 -rwx 11056 Mar 1 1993 10:27:17 +05:30 config.text
4 -rwx 804 Mar 1 1993 05:30:42 +05:30 vlan.dat
6 -rwx 2072 Mar 1 1993 10:27:17 +05:30 multiple-fs
7 drwx 192 Mar 1 1993 05:37:02 +05:30 c2960-lanbasek9-mz.122-44.
SE6
View 1 Replies
View Related
Feb 20, 2012
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
View 14 Replies
View Related
Aug 24, 2011
A visitor wants to use his laptop but I don't know the security code to get his computer to operate on my network. How do find that code and put it on my flash drive??
View 2 Replies
View Related
Dec 7, 2011
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies
View Related
Oct 5, 2010
I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
View 25 Replies
View Related
Feb 22, 2012
I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
View 5 Replies
View Related
Sep 14, 2011
I cannot edit or save file on a network drive. When saving or editing it says it cannot save and gives a read only error. I have tried to create a new folder and place files within but I still get the same error over and over again. When I check out the read only tab it comes back again.
View 1 Replies
View Related
Jun 29, 2011
For some reasons, my internet connection keeps dropping more often recently. My laptop still says it is connected to my network but I can just not have internet connection. It was not like that before but it happened more frequently now. What I did was to power off then on the modem and the router and everything will work fine again. I want to upgrade my firmware but I just wonder if I need to save all the configuration before doing the upgrading? If so, then how can I set it back to the old configuration that was saved?
View 5 Replies
View Related
Dec 1, 2008
Having trouble with resolving DNS entries with their WRT160Nv2? By resolving I mean, every once in a while, it browsers will just hang and say "Looking up..." When using nslookup, it says DNS timeout. DNS request timed out timeout was x seconds. Can't find server name for address xxx.xxx.xxx.xxx: Timed out Default servers are not available Default Server: UnKnown Address: xxx.xxx.xxx.xxx
I have the firmware 2.0.02_11 installed. Hooking directly up to the modem, I can resolve entries consistently. When I plug in the router, it works for a little, but becomes very unstable after some time. I spoke with support about this and they suggested changing the IP of the router, as well as lowering the MTU to 1400. Both did not improve stability.
View 9 Replies
View Related
Dec 6, 2012
I set up one AP-1041 that runs standalone IOS. No controller. I have three more that I want to copy the setup configuration over to. I have the right document, but which commands will get my set configuration from AP one FTP'd to my computer and how to copy that configuration back to another AP of the same model. This way I will only need to tweak a couple settings on the additional AP's instead of starting from scratch.
View 3 Replies
View Related
Jan 4, 2012
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies
View Related
Dec 19, 2011
Basically, her Windows (not sure which version) is telling her that to set up a secured connection, she needs to use a flash drive for some reason. She thinks she is able to get online right now, but only through an unsecured connection.
I don't think a flash drive is needed for this process, but as I am not even sure what this process is, I'm rather confused. What exactly is Windows asking of her right now? Her main thing is just to be able to connect to the Internet securely and easily.
View 6 Replies
View Related
Dec 19, 2011
Basically, her Windows (not sure which version) is telling her that to set up a secured connection, she needs to use a flash drive for some reason. She thinks she is able to get online right now, but only through an unsecured connection.
I don't think a flash drive is needed for this process, but as I am not even sure what this process is, What exactly is Windows asking of her right now? Her main thing is just to be able to connect to the Internet securely and easily.
View 9 Replies
View Related
Dec 13, 2011
I want to upgrade my router but I need a router that supports more port forwarding entries for my applications. I have my eye on the WRT310N router but I need to know how big its port forwarding table is.
View 2 Replies
View Related
Dec 20, 2011
I'm just trying to port forward with this router, and after I'm done entering all my settings, I click save settings, it tells me settings are successful.
But the it goes back to the port forwarding page and all the stuff is at default again as if I didn't make any changes. What the hell is this?
I'm sure it's just a little something I don't know about that's making it not save any changes to port forwarding.
View 3 Replies
View Related
