How do you save the command output from the CLI to a file on flash?
With IOS, I would normally use a pipe command to redirect to tftp, but the ASA doesn't support this as far as I can tell. As a work around I was thinking I could save the output to flash and then tftp that file off the ASA.
I deleted the flash from an ASA5510. I was able to tftp a version back into the device, but cannot seem to correctly have the box boot from this flash. I get the following error:
!WARNING: BOOT variable added, but not a valid image disk0: /asa831-k8.bin
*** Output from config line 41,"boot system disk0:/asa83..."
I have tried every save syntax i can think of to save this flash, but have yet to have it boot with an image ( I keep booting into ROMMON and have to tftp the image back in)
We have an ASA 5540 failover bundle working in Active/Standby mode. On our active asa 5540 when the sh run command is issued it gets stuck and displays the output after more than 15-20 mins.. and it takes another 10-15 mins to get back to the prompt..
However on the standby asa 5540 if the sh run command is issued, it displays the ouput and comes back to the prompt (even though this also takes 2-3 seconds)
I have tried rebooting the active asa 5540.We are running asa version 8.2.2.
how to storage the DHCP IP table in a external flash of a router. This is because the router is switched off and switched on everyday but I want that it remembers which MAC is associated with which IP when it starts again and avoid IP duplicate problems. The command "lease" doesn't seem useful here.
View 4 Replies View RelatedHow do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies View RelatedI am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies View RelatedI have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies View RelatedI got trouble when tried to save configuration by 'write memory' command.
cisco WS-C2960-48PST-L (PowerPC405) processor (revision G0) with 65536K bytes of memory. Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(52)SE,RELEASE SOFTWARE (fc3)
Cat2960#wr
Building configuration...
% Warning: Saving this config to nvram may corrupt any network management or security files stored at the end of nvram.
Continue? [no]: no % Configuration buffer full, can't add command:
After this message continue typing "yes" sometime that switch reload all times. The service compress-config command is not available anymore.
What would cause debug output to not show on a remote session via telnet connection where you've enabled terminal monitor?
The reason I ask is I was working with a client and we were debugging WCCP. I ran the debug ip wccp packets and events commands, then entered terminal monitor. After this, we saw nothing. We should have at least seen particular WCCP-related packets because we saw the necessary cluster view was established which can't be done without the exchange of these packets.
Can having syslog (logging) configured cause the issue? Did I use the command incorrectly?
I am facing issue while configuring service-policy output command in Cisco 7609-S router with c7600s72033-adventerprisek9-mz.122-33.SRE2.bin IOS. However, in the same series router having IOS c7600s72033-adventerprisek9-mz.122-33.SRC6.bin is supported service-policy output.Both the switch have WS-SUP720-3BXL SUP.
View 2 Replies View Related=>Routing Protocol in Question EIGRP.
=>Two equal metric routes for destination A(through R1 and R2-SVIs on two upstream 6500s)
Traceroute Output, is the output that alternates between 1.1=>10.1=>1.1 normal granted the two routes are "equal metric routes for the same routing procotol in use" or is that "round robin behavior" indicative of a routing problem?
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies View RelatedI have an 8 port Gigabit EHWIC in my Cisco 1921 router. A darn nice little switch module.
However, through my research, I am unable to find if I am able to change the way the NIC lights (green LEDs) on each port function. They basically just stay lit 100% non flashing when connected regardless of the port speed and duplex and ignore flashing for any activity.
Is there a deep layer command on these EHWIC cards to make them flash with activity like full standalone switches? Trust me when you have enough switch ports filled up it does make monitoring your networks health and activity by having the port led's respond to traffic flow. At least in my opinion.
I am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
I have ASA 5505 and I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
View 8 Replies View RelatedTrying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
I have the ASA5520, everyday I have a lot of connections through my ASA5520. But buffer in ASA5520 to save connections is limited. Now, I want my ASA can auto save the conn detail and Xlate to my Syslog server, how can i do that?
View 3 Replies View RelatedI have an asa5510 on 8.2.2. I have my logging configuration as below [code] I am not getting any syslog output to the syslog server. I'm using kiwi syslog server latest version. Have tried disabling/reenabling logging and changing inside host destinations. Is there another command needed
View 4 Replies View RelatedI'm having a bit trouble to limit the bandwidth on outgoing traffic with a Cisco ASA 5505.
In my case I want to limit the bandwidth to 31mbit/s up and down on the outside interface. but with my current configuration, just the download rate gets limited to 31mbit/s when I do a tptest. and the upload is around 40/50mbit.
Here is the policy configuration,
access-list outside_bw extended permit ip any any
class-map outside_bw
match access-list outside_bw
[Code].....
Need this file to erase my flash memory?
View 2 Replies View RelatedWe have a customer that has a ASA 5525-x reporting only 4g flash memory rather than 8g has any 4g version of the 5525 or is the IOS reporting incorrectly the size, as it seems to be embedded on these units as a USB disk internal.
View 4 Replies View RelatedI am in the process of setting up the ASA5520 with the latest 8.4 firmware latest Anyconnect 3.0.
Unfortunately, the internal memory is sufficient enough for the ASA ASDM only. It says not enough memory when I tried to tftp the Anyconnect pkg.There is a external flash slot at the back of the ASA, I've inserted a 256mb CF card but when I do a show disk1: it shows
I just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin
Source file name []? asa804-k8.bin
Address or name of remote host [192.168.10.2]?
Destination file name [asa804-k8.bin]?
Writing file tftp://192.168.10.2/asa804-k8.bin...
!%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect)
Cisco asa#
I am needing to upgrade the Flash card on our current ASA from 64mb to a 1GB card to make way from upgrading from 8.0 to 8.4. When i copy all the contents from the 64MB card through a card reader i am not getting the startup-config file copied over. I checked to make sure that all hidden files are shown, but i am not seeing it. I backed up the startup-config from the old 64mb card to a tftp server before switching the cards out. Is their something that i am missing?
View 4 Replies View RelatedI've multiple FWSMs running. The funny thing: When I do a "show resource usage" I have one blade showing a "Conns [rate]" and "Syslogs [rate]" values and one blade isn't.
SSH 4 5 15 0 admin
Syslogs [rate] 1 437 unlimited 0 admin
Conns 149 23465 unlimited 0 admin
Xlates 154 2877 unlimited 0 admin
Hosts 154 2877 unlimited 0 admin
Mac-addresses 6 7 65535 0 admin
All modules are running the same software version 3.2(10).And the even more funny thing is: on one blade I have different output for all the contexts on it.What's the reason for that behaviour? A bug?
In order to do a flash upgrade on a 5510, is there any way to get the files from the existing flash onto the new flash before you replace existing flash? Is there an online procedure?
View 2 Replies View RelatedI need to upgrade the ASA 5520 from OS 8.2(5)26 to 8.2(5)33. the ASA only has 64M of flash. I have a 256M flash card. What are the steps to upgrade the flash? I am not sure how it will boot up because the new flash will be blank?
View 2 Replies View RelatedI was trying to erase some bad test configs on my 5505 with a write erase, but all VLAN and Ethernet configs remained. I hastily decided to do an erase flash. No I'm stuck at a ROMMON prompt with no image found to boot I'm hoping I don't have to TFTP a factory image. How do I find the images on disk0 and copy them?
View 16 Replies View RelatedMy client has had to replace their ASA 5510. Upon importing the image to the brand new ASA they are unable to write to the flash.
They have run fcsk disk0: to no avail. show file system show 0 and 0 for Flash size and Free space on disk0.
Is there anything that can be done, short of formating flash and trying to reinstall the image? I have asked them to reload the ASA but they are reluctant to do so as they don't want the site to lose connectivity.
I have two pix525 firewalls cann't boot up normaly and i find [[URL] no longer provides the falsh erase tool ,erasedisk.bin,download.
View 4 Replies View RelatedI need to upgrade the compact flash of my ASA 5510 from 256MB to 512MB. A friend's recommendation was to buy a card reader, copy all of the data from the existing card and paste it to the new compact flash. I have a hard time believing that it's that straight forward.
Any safer, more foolproof way of migrating between flash cards?