I have ASA 5505 and I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
View 8 RepliesI have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
[code]...
I have Linksys SPS224. I've learnt how to change some parameters through SNMP. But this changes are applying to running-config, and, when switch reboots, all loose.
How can I save this changed running-config to startup-config through SNMP?
I am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies View RelatedI have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.
I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in: "Building configuration... [OK] -> NVRAM Verification Failed".
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedWhat is the factory default config on ASA5505 with 8.4.1?
View 3 Replies View Relatedmy Cisco ASA 5510 doesn't save the configuration to the disk.
View 1 Replies View Relatedworking config with least amount of code for:
IOS post 8.3
Subnet: 192.168.1.0 /24
Static NAT (from any source) to server 192.168.1.100 and allow the same incoming connections on outside interface
Ports:
TCP 20,21
TCP 80
UDP 50000-50020
I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.. then what i do is a copy start run to get the configuration active..
View 2 Replies View RelatedI have users that are unable to save their changes to topology maps - when devices are moved in a map and the map is exited, the next time the user goes into the map it is back at the default layout. The unusual part is that this does not affect all users - I have two users with the same CiscoWorks rights, but only one can save map changes. The admin user is one that can't save map changes. I'm running LMS 2.2 on Solaris 2.8. The problem existed before and after I upgraded to Campus Manager IDU 11, and stopping and starting services hasn't worked.
View 7 Replies View RelatedDue to problems with the D view cam, I have reset my IP camera DCS-930L but I can't register the password, it says "There was a problem saving your settings. Press next and try again." I can't get pass saving password, tried all the previous passwords but none works.
View 2 Replies View RelatedI have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
Here is the error that I am receiving:
switch#copy run startup-config
Destination filename [startup-config]?
Building configuration.
I just tried to configure my ASA but unable to ping. My setup is as follows:
Cable Modem (DHCP from IPS)---> ASA (192.168.1.1)--->Belking Router (192.168.5.1)--->Switch (192.168.5.14)--->
ASA Version 8.2(3)
!
hostname WoodHomeASA-1
[Code].....
First time attempting to set up a 5505. Trying to replace a snapgear firewall and replicate the settings to the 5505.
View 12 Replies View RelatedI have a command line from ASA 5505 like below :
nat (inside) 0 access-list NO_NAT
The problem is I cannot see any matching ID of 0 at the (outside) like :
nat (outside) 0 xxxxxxxxxxxxx
Another problem is there is also no any access list with the name of NO_NAT.
I am using ASA 5505.Below are my sh run.I am not able to ping my gatway i.e 182.73.131.89
interface Ethernet0/0
description Internet Interface
switchport access vlan 61
!
interface Ethernet0/1
description office Internet
switchport access vlan 50
[code]....
We are facing problem with cisco 6506 switch while configuring when we try to save it, we are not able to save the config, neither we are able to view running and startup config.
View 2 Replies View RelatedI have config ASA 5505 and it is conencted to layer 3 switch that connects to cable Modem.
ASA is config with DHCP option and PC is able to get the IP from ASA. But from PC i am unable to access the internet. From ASA itself i am able to ping the Websites fine.
ASA has config with DHCP for inside and also it is doing NAT.
When i connect the ASA directly to Cable modem then pc is able to access the internet.
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
We have a cisco asa 5505 on which we have setup a group VPN. The VPN connections from all cisco vpn clients works fine except one. The keep getting the below error
"Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding. Connection Terminated".
Not sure why only one client won't be able to connect. The version we are using is 5.0.02 for VPN client.
I am unable to Telnet/SSH/RDP from my inside network to my DMZ. I am not sure where the problem lies, I am able to use VNC from the inside to the DMZ (ports 5800, 5900), and also establish connection on Ports (26700-26899). I have a computer connected directly to the DMZ and those services work to all networks on the DMZ.I have attached Logs of successful VNC connections, unsuccessful RDP and Telnet sessions, and the running config.
View 23 Replies View RelatedI configured a new Asa 5505 with Ios 8.44-1-k8.bin and when I installed the Asa the client's after about 1 hour were unable to ping or map drives to the Asa. I got the following error,%ASA-2-106007: Deny inbound UDP from XXXX to XXXX due to DNS Query. I added the command same-security-traffic permit intra-interface they were then able to ping the server and connect to the Internet, but still unable to map drives i could see the connections from the Pc's to the server in a show conn with was tcp port 445 with Saa? I reverted back to Ios 8.25 and everything works.
View 2 Replies View RelatedWhen I have a computer directly connected to the Cable Modem I get 9.84MB Down and 1MB Up. When I put it behind the ASA 5505 with policing on the interface, I only get 4MB Down and 660Kb Down.What I'm wanting to do is setup this up to enable my VoIP to have a higher priority and shave 128kon both the Up/Down for the VoIP traffic. I also want to make sure I don't exceed the inbound and outbound thresholds.I''m using a 5505 Security Plus?
View 3 Replies View RelatedI have 2 subnets bought from my provider 194.102.98.128/27 and 194.102.98.160/27.
From my provider a have the following setup:
IP Address: 86.120.151.66
Netmask: 255.255.255.128
Gateway: 86.120.151.1
DNS (1): 213.154.124.1
DNS (2): 193.231.252.1
My IPs are static routed by my provider thought 86.120.151.66 .
On the firewall I have the following set-up:
Outside Interface: 86.120.151.66/25 security level 0
DMZ interface: 194.102.98.129/27 security level 50
Inside Interface: 194.102.98.161/27 security level 100
0.0.0.0 0.0.0.0 [1/0] via 86.120.151.1, outside
Everything works perfectly except when I try to sent an email. The email gets sent (eventually), but afert a long waiting time, 45-60 sec. The connection is opened instally to the server but then just hangs there for 40-50 sec. The problem is that a have an aplication on a server that has to send confirmation emails, and that aplication is limited to a 30 sec timeout for conecting to the mail server, much less then the 45-60 sec that I have now. The mail server is hosted by a data center, it is not in my networks (location).
I have tried deleting the ESMTP inspection, that doesn't work. Pinging my mail server rezults in a average time of 20 ms. And when a do a tracert the hight value in a hop doesn't usually pass 80 ms, the average is 20-25 ms.
The problem is ONLY when sending emails. Everything else works perfect, including receiving emails from the same server.
My running config is:
hostname ASA-Adisys
domain-name Intern.ro
enable password 0./39zRW9yhKK/bO encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
Remote LAN pool is configured as inside. Route is proper. I am able to open 443 port from the remote LAN pool on the ASA. That means, the port is open from the remote pool. No response if I try https on the browser.
View 11 Replies View RelatedI found a tricky task for our ASA 5505 firewall. I am not able to go internet when using DHCP but I can access by using fixed IP address in client PC.Same IP, Same Mask, Same DNS, Same Gateway. All the same but no hope. Any configuration i missed in firewall?
View 5 Replies View RelatedI'm unable to have any internet connection for my new setup.
here's the overview.
Current setup is
Internet -> Router -> PIX 501 -> Switch -> clients
Internet -> static ip given is 210.193.34.1 - 210.193.34.6
Router -> Static ip assigned for NAT/External is 210.193.34.1, Local ip is 192.168.1.246
PIX 501 setting ->
IP to Router, According to router screen is 210.193.34.2, but not sure what settings are done in the PIX itself as I'm unable to access it.
local ip is 192.168.1.1
Clients - > 192.168.1.0
Old setup is working fine and connected to internet. for the new setup, as i do not want any downtime for the old setup.
As you can see, there are two firewalls connected concurrently to the router. I've configured it this way.
Internet -> Router -> ASA 5505 -> Switch -> clients
ASA 5505 setting ->
IP to Router NAT/External/ Outside Interface, 210.193.34.6 (Or do i set as 192.168.1.0?),
local ip/ Inside Interface is 192.168.2.1
Clients - > 192.168.2.0
some setup details.
security policy, NAT, set to default. routing is route outside 0.0.0.0 0.0.0.0 210193.34.6
I'm unable to access after a week of troubleshooting.
I have a user that is trying to save an excel speadsheet that is located in a shared folder on a server, the user can open the file and edit ok but when they try to save the file the progress bar pops up but just hangs then a message pops up to saying "file not saved". They are using Windows 7.The user is new and I have just set up their account so thought it might be permission issues but I have logged the user in on two other different machines (1 win7 and 1 WinXP) and they have no problem at all.
View 7 Replies View RelatedI have ASA 5505 with base license. I created 3rd vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
Code...
i can't get it working to expose on internal server to an outside interface.I used the public server function in ASDM.Internet access works if i nat my private adress to one of the available ipadresses provided by our isp.
Internal Server : owncloud 172.10.0.4
External Server : ext181 46.245.171.181
I can't see the error in the configuration,
: Saved
:
ASA Version 9.1(1)
!
hostname rhedetest
domain-name xxxxx.de
enable password 59t92OvRofWL9yf3 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code]....
I have upgraded an ASA 5505 to 9.0(1) as I would like to use ipv6 version of dhcprelay. That said, I am unable to obtain a global unicast address but the link-local address is able to communication with the ISP's gateway/DHCP provider which I hope will allow v6 dhcprelay provide internal clients with IP's from the ISP. Trouble is, unsolicated inbound ICMPv6 messages from the ISP's gateway are being dropped on the way into outside interface.
%ASA-3-313008: Denied IPv6-ICMP type=129, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
[Code]...
I have assigned a task to configure a vpn between windows 2008 server and cisco asa 5505, what kind of vpn should i go with as the windows 2008 server r2 is on cloud and is it possible to configure site-to-site vpn for this network senario or not.. i have try ikev1/ipsec remote access vpn with l2tp with (CHAP, MS-CHAP v2) and couldn't find any document which will allow me to configure windows 2008 server to behave a client and connect it to asa, well what i did is that i configured a dail-up connnect with l2tp and found the following debug message
Sep 09 20:04:02 [IKEv1 DEBUG]IP = 172.16.32.5, Oakley proposal is acceptable
Sep 09 20:04:02 [IKEv1 DEBUG]IP = 172.16.32.5, IKE SA Proposal # 1, Transform # 1 acceptable Matches global IKE entry # 1
[Code].....