I just tried to configure my ASA but unable to ping. My setup is as follows:
Cable Modem (DHCP from IPS)---> ASA (192.168.1.1)--->Belking Router (192.168.5.1)--->Switch (192.168.5.14)--->
ASA Version 8.2(3)
!
hostname WoodHomeASA-1
[Code].....
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
I configured a new Asa 5505 with Ios 8.44-1-k8.bin and when I installed the Asa the client's after about 1 hour were unable to ping or map drives to the Asa. I got the following error,%ASA-2-106007: Deny inbound UDP from XXXX to XXXX due to DNS Query. I added the command same-security-traffic permit intra-interface they were then able to ping the server and connect to the Internet, but still unable to map drives i could see the connections from the Pc's to the server in a show conn with was tcp port 445 with Saa? I reverted back to Ios 8.25 and everything works.
View 2 Replies View RelatedI've been called upon to fix the SSL VPN issues in our ASA5505. The issue I am having is that I am able to log into the vpn, access the internet, but I'm unable to access anything on the LAN. I can't use ping or use DNS.
I'm using ASDM v. 6.2(1) and ASA verison 8.2(1). I'm not comfortable using the CLI and prefer the GUI.
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
Internet ISP -> Juniper SRX 210 Ge-0/0/0
Juniper fe0/0/2 -> Cisco ASA 5505
Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30)
2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA.
2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop.
3. Allowed all services in untrust zone in bound traffic in Juniper SRX.
4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
We are going to impliment Spectrum (CA) in my network,i have ASA-5580-20 firewall now my spectrum server want to communicate with firewall,then only it will discover the firewall logs.Now the problem is my spectrum server is in MZ zone(10.10.10.45) security leval is 70 and my inside interface(10.20.20.101) security leval is 100.
I am unable to ping from spectrum server to firewall because of high security leval.How can i solve this problem,can i change my inside security leval to 69 then i think it will ping.
i am trying to get my ASA 5505 with 2 internal VLANs (voice and data) and external internet VLAN to run in router as a stick, and route between VLANS.
I cant get it working though:
[code]...
We want to use an ASA as a pure routing device. Our network has several internal subnets (10.1.x.0/24), and we want to be able to reach them from outside and to allow access between them.
We have a defined a VLAN for each subnet range with the same security-level, added it to an Ethernet port and made the Ethernet that acts as outside as a trunk, and defined it as the global routing.
We cannot ping any of the subnet IPs defined in the ASA from outside nor we can ping it from the internal IP addresses.
Configuration:
: Saved
:
ASA Version 8.2(1)
[Code].....
I am trying to configure Nat on a clean ASA 5505, but can't get it to work. I ran the commands below. On the ASA I can ping the internet and inside vlan ip. On my laptop I can ping the ASA inside vlan ip, but I can't ping the outside vlan ip. From another network I can ping the ASA outside public ip. Is there an access-list that denies inside from accessing outside?
I am running version 8.4(3) and I erased the existing configuration.
ASA(config)# interface vlan 1
ASA(config-if)# ip address 10.0.0.1 255.255.255.0
ASA(config-if)# nameif inside
[Code].....
I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254
I have been tasked with replacing our company eSoft router with a Cisco ASA 5505 with the upgraded security license. I have been working on the configuration for a couple of weeks now, after reading hundreds of forum posts, watching youtube videos, and endless google searching, and despite my best efforts I am still having an issue I can’t figure out.
I have a couple of subnets, that when the ASA is connected, I cannot ping, nor can they get to the internet or our Exchange server. At this point I’m not sure if it’s an access rule issue, NAT issue, or DNS issue.
Here is the network layout:
ASA: 192.168.0.2 (Primary Gateway)
192.168.0.0 (Primary facility, ASA is the gateway)
192.168.2.0 (Second facility, connected via Verizon point-to-point)
192.168.3.0 (Third facility, connected via Verizon point-to-point)
[Code].....
I am trying to troubleshoot an ASA5505 connectivity issue. My initial tests are to ping the Internet router from the ASA This is failing and also a sh arp only shows internal addresses.
I have to go to site to check this out to confirm the following.
1: Should I be able to ping the Internet router from the ASA?
2: Do I need to permit any icmp to do this?
3: Should a sh arp show the address of the internet router?
I tried entering the command permit icmp any outside
However I got the error route already exists 0.0.0.0/0.0.0.0
I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies View RelatedI've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
ASA Version 8.2(5)
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
[Code] .....
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
I have a ASA 5505. I want to be able to ping from my workstation to some address, lets say [URL]. My workstation is connected to Ethernet 0/2. I have tried playing around with the ACL but am not able to accomplish this.
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasadomain-name home.7vnmotorsports.com
[Code]....
Before upgrading to 8.4(4)1 I was able to ping our inside interface accross the VPN. Now I cannot. Because ping is not working, my SNMP server thinks that the device is offline however I know the VPN tunnel is still up and the remote branch office is working fine. Here is the config of the branch office ASA 5505 in question. How to get icmp working again?
ASA Version 8.4(4)1
!
hostname BranchASA5505
domain-name houston.deh
[Code].....
Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies View RelatedI have, what I believe to be, a simple issue - I must be missing something. Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209). There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off. The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue. Basically, the VPN is up and running but PC 10.51.253.210 cannot get out
ASA Version 7.2(4)
!
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
[Code]...
I have the following setup.
host PC (192.168.9.3) -----> gateway (192.168.9.2) ----- Pix E1 (192.168.9.1)/Pix E0 (81.x.x.250) ------ Internet
The 192.168.9.2 gateway is a 3560 switch connected to the PIX. I can ping out to the Internet via IP from the PIX, but not via the host PC (192.168.9.3) on the LAN. PIX and gateway configs below. Am I missing something that's preventing me pinging out to the Internet from the internal LAN?
PIX config
test-cal-pix01# sh run
: Saved
:
PIX Version 8.0(3)
!
hostname test-cal-pix01
enable password btf1YD.Vq7mE6vEA encrypted
[code]....
I am having a problem configuring my ASA 5505 for NAT.
View 3 Replies View RelatedI' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0
Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.
We have two ASA5510s, each with outside interfaces to the same two ISPs (different IP addresses within the same subnet, of course). Both ASAs allow ICMP on all (inside and outside) interfaces. One ASA's default route is to ISP-1 and the other is to ISP-2. We can ping the default gateways for both ISPs from only one ASA. From the other ASA, we can only ping the default gateway for the default route but not the other. The pings originate from an inside client, first configured with the default gateway for ASA-1, then for ASA-2. Why does this happen, how do I troubleshoot something like this and how do I fix it?
View 1 Replies View RelatedOne of my client has BSNL leased line with LAN IP POOL we configured those on ASA 5510 nad Internet working fine but from cloud we are not getting any response for ping requiest please find running configuration below:
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(1)
[Code]....
one of my SNMP server 10.242.103.42 sits in MZ zone,and ACE 4710 is connected to core switch,coreswitch is connected to firewall asa.
Now iam trying to ping from MZ zone SNMP server to loadbalancer ip 10.242.105.1,iam unable to ping my LB interface to discover SLB on my SNMP server.
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
I have 2 modules of FWSM in 6500 switch (failover). I need 5 context. When I use in routed mode (like in the picture) , I cannot ping the servers behind the firewall. (I have ping to FW context) In transparent mode, it is not happening.
View 1 Replies View RelatedWhen I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedI have created a VPN connection for ASA 5512-X by using the wizards and nothing seems to be wrong on the wizards's config.I am able to connect to the network by using the VPN but unable to ping internal network.Below is my config for your reference:
Result of the command: "sh run"
: Saved
:
ASA Version 8.6(1)2
!
hostname FAA-ASA-1
enable password crzcsirI44h2BHoz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
First time attempting to set up a 5505. Trying to replace a snapgear firewall and replicate the settings to the 5505.
View 12 Replies View RelatedI have a command line from ASA 5505 like below :
nat (inside) 0 access-list NO_NAT
The problem is I cannot see any matching ID of 0 at the (outside) like :
nat (outside) 0 xxxxxxxxxxxxx
Another problem is there is also no any access list with the name of NO_NAT.