Cisco Firewall :: ASA 5505 / Cannot Access Internet Or Ping From Inside Interface?
Jul 26, 2011I am having a problem configuring my ASA 5505 for NAT.
View 3 RepliesI am having a problem configuring my ASA 5505 for NAT.
View 3 RepliesI have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies View RelatedI have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
administrator wants to manage ASA 5500 using inside interface.{telnet or ssh].Allowed telnet and ssh in ASA 5500 but unable to get access from administrator PC..Is there a way to do it without enabling NAT on the ASA? Will a specific rule on ASA allow adminstrator to access ASA 5500 inside interface via ssh or telnet?
View 2 Replies View RelatedI ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View RelatedThe ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedI am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedI have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View RelatedI am connecting the inside interface to an upstream switch and therefore will need to assign a static IP address to the inside address as I did below:
#sho int ip brief
Vlan1 123.123.123.123 YES manual up up
I will also use this to manage the ASA. I am having a problem with the network configuration of the inside interface as I can't ping the gateway and/or the in IP of the inside interface.Do I need to add any routes?
We have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
here is output from our sys log:
SyslogID Source IP Dest IP Description
305006 172.18.22.3 portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
To give some clarification:
172.18.22.3 is one of our DNS servers
172.18.22.156 is a device we're experimenting with.
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
: Saved
:
ASA Version 7.2(3)
!
hostname [redacted]
[code].....
Trying to add inside routes on an ASA 5505 to point traffic to another gateway for other connected networks is resulting in the following error 6Sep 16200 819:13:5810601510.184.236.1265003810.170.54.1823389Deny TCP (no connection) from 10.184.236.126/50038 to 10.170.54.182/3389 flags RST on interface insideI believe the problem is due to the Asymetric tcp connection and the ASA is dropping the connection because it only see one half of the traffic.Is there a way we can stop the firewall dropping the TCP connections on the inside interface? i've tried removing the threat managment which didnt work.Annoying thing is were putting the ASA 5505's in to replace old Watchguard soho firewalls only the watchguards forwarded the traffic no problem at all.
View 1 Replies View RelatedI have a pair of 5505's in transparent mode and connected them to C2960S. The inside interface (which is VLAN5 on the switchport) keeps dropping, going in to error state. There is no log reference in the switch and the interface shows as UP. The standby ASA has no problem, both interfaces on the switch is up. As soon as I failover the units over, the active node inside interfaces drops.
View 2 Replies View RelatedWe've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies View RelatedI have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
I did this on the PIX and it worked like a charm, but I am having some difficulty translating the configuration to an ASA.
In the PIX I performed NAT on outside traffic to a specific inside host (web server) to map to the inside interface so that return traffic would go to the same firewall the traffic came in through, The reason for this configuration was because the gateway of last resort was a different firewall and not the firewall the traffic came in through.
Now to further give you some history, the gateway of last resort is an ASA running 9.1 (Now), prior to that it was a PIX with v8.0(4), traffic to the aforementioned web server came in through the gateway of last resort), which at the time was the PIX.
However, for some reason after swapping the PIX for an ASA (same rules, updated NAT rules for 9.1) access to the same web server is slow. Not sure why, but it’s the case. To alleviate the slowness we experienced, and until I can figure out why this occurs on the ASA, I placed a PIX on the network that only listens for traffic for the web server in question. On this PIX I map to the inside interface so that traffic flow works and external clients can access the web server with no issues.
So two questions, one I would like to use the configuration I have for the web server on the PIX on the ASA to see if that setup on the ASA works better, but having difficulty translating the rules to the ASA.
Second question, (Slow access with ASA to a web server, but fast with PIX to the same web server)?
P.S. Addresses in attached picture config are not real, but I know what they translate to.
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
Configuring an asa 5505 with 8.42 software.I need to access an https server on the inside via the outside interface. have moved the http server enable to port 10443.Tried to make a "network object nat rule"
object network Vejrstation nat (any,outside) static interface service tcp https https object network Vejrstationnat (any,outside) static interface service tcp https https.
We have an ASA5505 UL bundel, updated with this license "L-ASA5505-SEC-PL=" to enable traffic from DMZ to Inside. No NAT or rules deployed for that yet.
On the Inside we have Exchange 2007 in a single server installation. The public url for smtp, ActiveSync, OWA and Outlook Anywhere is mail.company.se. There is a static NAT for outside traffic to access above mentioned services on inside. Now, on DMZ there is the WLAN for guests to access the Internet. How ever, our Smart Phones with WLAN turned on, cannot sync to the Exchange Server on the Inside! The DMZ gets IP-addressen from ASA on DMZ Interface with external DNS configured. How can I configure the ASA to achieve the function of ActiveSync from DMZ to Inside with the public URL from the phones?
My internal network consists of Catalyst 3750 switches segmented into different VLANs. There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510. However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510. I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN.
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface. I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet.
Here is my config that pertains to this setup:
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I've tried the following commands below but no dice.
same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable. [code]
View 1 Replies View Relatedso i have a ASA 5510. The ASA is Connect with the Internet through PPOE DSL MODEM
The outside Interface get an IP. The Inside Interface get through DHCP from the ASA the Internet DNS SERVER (T-Online) But the HOST do not connect to the Internet because the DNS Server is timed out
Code...
I'm having trouble setting up the correct rules on an ASA 5505 I'm using in my home office. I have a couple of IP Cams I need to access remotely.
I've tried setting up simple NAT(PAT) and/or Access Rules, but it hasn't worked. I have a single dynamic IP for the Outside interface. Call it 77.76.88.10 and I am using PAT. The CAM is setup to connect on port 80, but could be configured if necessary. I've tried setting up NAT Rules using ASDM as follows:
Match Criteria: Original Packet
Source Intf = outside
Dest Intf = inside
[Code]....
I'm afraid to use CLI only because I am not confident I'll know how to remove changes if I make a mistake.
I have recently installed an ASA5510 at a site in South Africa to connect via VPN to a site in the UK (ASA5520). The VPN comes up fine with the 5520 in the UK, however, I can not connect to the inside interface over the VPN, but can access it from the internal LAN. All other hosts on the LAN are accessible over the VPN.
The 5510 also has another VPN to another site in SA and the 2nd site cannot ping the interface either.
I am trying to configure Nat on a clean ASA 5505, but can't get it to work. I ran the commands below. On the ASA I can ping the internet and inside vlan ip. On my laptop I can ping the ASA inside vlan ip, but I can't ping the outside vlan ip. From another network I can ping the ASA outside public ip. Is there an access-list that denies inside from accessing outside?
I am running version 8.4(3) and I erased the existing configuration.
ASA(config)# interface vlan 1
ASA(config-if)# ip address 10.0.0.1 255.255.255.0
ASA(config-if)# nameif inside
[Code].....
I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
I have a ASA 5505. I want to be able to ping from my workstation to some address, lets say [URL]. My workstation is connected to Ethernet 0/2. I have tried playing around with the ACL but am not able to accomplish this.
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasadomain-name home.7vnmotorsports.com
[Code]....
I would like to allow users from network 10.132.23.0/24, 10.132.33.0/24, 10.132.24.0/24 access to our SQL server(192.168.1.7) located on the inside interface(192.168.1.0/24 network) Those networks (10.132.0.0/16) come from the DMZ interface.
View 12 Replies View Related